One Stop Systems OSS-PCIe-HIB38-x8-DUAL Manual de usuario

User Manual,

PCIe x8 Gen3 Dual and Quad Cable Adapters

OSS-PCIe-HIB38-x8-DUAL

OSS-PCIe-HIB38-x8-QUAD

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 2

Table of Contents

1. Overview

1.a. Host cable adapter................................................................................................................................3

1.b. Target cable adapter.............................................................................................................................3

1.c. Specifications ........................................................................................................................................4

1.d. block diagram........................................................................................................................................4

2. Switch Settings

2.a. Switch Settings......................................................................................................................................5

3. Initial set-up

3.a. Unpacking instructions..........................................................................................................................5

3.b. Installation and Removal.......................................................................................................................5

3.c. Installing the host cable adapter............................................................................................................6

3.d. Removing the host cable adapter..........................................................................................................6

3.e. When using with any third party I/O device ...........................................................................................7

4. Ordering information

4.a. Ordering Information .............................................................................................................................7

5. Appendix

5.a. Appendix... ............................................................................................................................................7-12

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 3

1. Overview

This manual describes two boards, the base board which provides the dual port adapter and the mezzanine when added to

the base board provides the quad port adapter. There are no software drivers required to operate these boards.

1.a. Host cable adapter

The host adapters (Part # OSS-PCIe-HIB38x8-DUAL and OSS-PCIe-HIB38X8-QUAD) install in the host computer’s PCIe x16

I/O slot, allowing communication between the processor and multiple I/O points.

1.b. Target cable adapters

The target cable adapters (Part# OSS-PCIe-HIB38-x8-DUAL and OSS-PCIe-HIB38X8-QUAD) install into the target slot of

any OSS target backplane and extend the PCIe bus to a single or multiple add-in boards installed in the I/O slots of the target

backplane.

Slot Cover

PCIe

x8Connector

Mezzanine connector

Switch

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 4

1.c. Specifications

Dimensions (H x L): 4.0 x 5.85 inches (10.16 x 14.85Cm)

Front Panel Connectors: Dual PCIe x8 cable connector

Front Panel Indicators: Power On / Cable Present LEDs

Power Consumption (designed to meet the following conditions) 3.75W typical, [email protected]

Operating Environment (designed to meet the following conditions)

Temperature Range: 0° to 50°C (32° to 122°F)

Relative Humidity: 10 to 90% non-condensing

Agency Compliance: UL60950.FCC Class B, CE safety and emissions

1.d. Block Diagram

Quad Mezzanine

Dual Board

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 5

2. Switch Settings

3. Initial Set-Up

3.a. Unpacking Instructions

1) If the carton is damaged when you receive it, request that the carrier’s agent be present when you unpack and inspect the

equipment.

2) After unpacking, verify that all items listed in the packing list are present.

3) Inspect the equipment for shipping damage.

4) Save all packing material for storage or return shipment of the equipment.

3.b. Installation and Removal

1) Power down the host system.

2) Open the chassis according to your system documentation.

3) Remove the host cable adapter from the protective bag, observing proper ESD safety procedures.

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 6

3.c. Installing the Host Cable Adapter:

1) Insert the host cable adapter into a PCIe Gen3 x16 in the host system slot. Make sure that the card is well seated and

tighten the screw on the face plate.

2) Attach the cable by first pulling back on the retractor ring. With the keyed slot aligned with the connector key ridge on the

slot cover, insert the cable connector into the connector shell on the board until the connector teeth snap securely

into the holes in the cable shell.

3) The connectors on either end of the PCIe x8 cable are identical. Each connector is equipped with a retractor to allow the

connector to be locked into place.

3.d. Removing the host cable adapter

1) To remove cable pull back on green thumb tab to release metal pins and gently separate.

2) Loosen and remove the screw before removing the Host Cable Adapter from the card slot.

Connector Teeth

Holes in the

Cable Shell

Output swing control

dip switch (Table 2)

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 7

3.e. When using with any third party I/O device:

1) Install the downstream board into the appropriate PCIe slot.

2) Connect the external power source (separate from the host system power supply) to the downstream device if necessary.

3) Connect the PCIe cable to both the upstream host adapter and the downstream device.

4. Ordering Information

OSS-PCIe-HIB38-x8-DUAL –PCIe x8 Gen3 host cable adapter installs in a x4, x8 or x16 expansion slot of a host system to extend

the host bus to an expansion system or PCIe device.

OSS-PCIe-HIB38-x8-QUAD - PCIe x8 mezzanine board is attached to the dual board adding 2 additional slots

Order online at www.maxexpansion.com or call toll free 877-438-2724

Appendix

Pin Assignments

Connectors PCIe x8 Card Edge Connector

The pins are numbered as shown with side A on the top of the centerline on the solder side of the board and side B on the

bottom of the centerline on the component side of the board.

The PCIe interface pins PETpx, PETnx, PERpx, and PERnx are named with the following convention: “PE” stands for PCIe

high speed, “T” for Transmitter, “R” for Receiver, “p” for positive (+), and “n” for negative (-).

Note that adjacent differential pairs are separated by two ground pins to manage the connector crosstalk.

Customer target mode signals for use with OSS products

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 8

Pin #

Side B

Side A

Name

Description

Name

Description

+12V

12V Power

PRSNT1#

Hot-Plug presence detect

+12V

12V Power

+12V

12V Power

+12V

12V Power

+12V

12V Power

GND

Ground

GND

Ground

SMCLK

SMBus clock

JTAG2

TCK

SMDAT

SMBus data

JTAG3

TSTCLK+

GND

Ground

JTAG4

TSTCLK-

+3.3V

3.3 V power

JTAG5

TMS

JTAG1

PWR_ON#

+3.3V

3.3 V power

3.3Vaux

3.3 V auxiliary power

+3.3V

3.3 V power

WAKE#

Signal for link reactivation

PERST#

Fundamental reset

Mechanical key

RSVD

Reserved

GND

Ground

GND

Ground

REFCLK+

Reference clock (differential pair)

PETp0

Transmitter differential pair, Lane 0

REFCLK

PETn0

GND

Ground

GND

Ground

PERp0

Receiver differential pair, Lane 0

PRSNT2#

Hot-Plug presence detect

PERn0

GND

Ground

GND

Ground

PETp1

Transmitter differential pair, Lane 1

RSVD

Reserved

PETn1

GND

Ground

GND

Ground

PERp1

Receiver differential pair, Lane 1

GND

Ground

PERn1

PETp2

Transmitter differential pair, Lane 2

GND

Ground

PETn2

GND

Ground

GND

Ground

PERp2

Receiver differential pair, Lane 2

GND

Ground

PERn2

PETp3

Transmitter differential pair, Lane 3

GND

Ground

PETn3

GND

Ground

GND

Ground

PERp3

Receiver differential pair, Lane 3

RSVD

Reserved

PERn3

PRSNT2#

Hot-Plug presence detect

GND

Ground

GND

Ground

RSVD

Reserved

PETp4

Transmitter differential pair, Lane 4

RSVD

Reserved

PETn4

GND

Ground

GND

Ground

PERp4

Receiver differential pair, Lane 4

GND

Ground

PERn4

PETp5

Transmitter differential pair, Lane 5

GND

Ground

PETn5

GND

Ground

GND

Ground

PERp5

Receiver differential pair, Lane 5

GND

Ground

PERn5

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 9

PETp6

Transmitter differential pair, Lane 6

GND

Ground

PETn6

GND

Ground

GND

Ground

PERp6

Receiver differential pair, Lane 6

GND

Ground

PERn6

PETp7

Transmitter differential pair, Lane 7

GND

Ground

PETn7

GND

Ground

GND

Ground

PERp7

Receiver differential pair, Lane 7

PRSNT2#

Hot-Plug presence detect

PERn7

GND

Ground

GND

Ground

Notes:

1 Optional signals that are not implemented are to be left as no connects on the board side connector.

2 Reserved signals must be left as no connects on the board side connector.

3 Although support of CWAKE# is optional from the board side connector perspective, an allocated wire is mandated for the cable

assembly.

4 Board side pin-out on both sides of the Link is identical. The cable assembly incorporates a null modem for the PCIe transmit and

receive pairs.

PCI Express x8 Connector Pin Assignment

Row A

Row B

Row A

Row B

Row A

Row B

Pin #

Signal Name

Pin #

Signal Name

Pin #

Signal Name

GND

PETn4

PERp4

PETp0

PERp0

CREFCLK+

PWR (3.3V)

GND

PETn0

PERn0

CREFCLK-

PWR (3.3V)

PETp5

PERp5

GND

PWR (3.3V)

PETn5

PERn5

PETp1

PERp1

RSVD

PWR RTN

GND

PETn1

PERn1

RSVD

PWR RTN

PETp6

PERp6

GND

SB_RTN

PWR RTN

PETn6

PERn6

PETp2

PERp2

CPSRNT$#

CWAKE#

GND

PETn2

PERn2

CPWRON

CPERST#

PETp7

PERp7

GND

PETn7

PERn7

PETp3

PERp3

PETp4

GND

PETn3

PERn3

PETn4

PERp4

Row A, Pin 1

Row B, Pin 19

Table 1: Pin-out for the PCIe Gen3 x8 Card Edge Connector on the Host Cable Adapter

PIN- out for the PCIe x8 Cable

One Stop Systems OSS-PCIe-HIB38-x8-DUAL/QUAD

Specifications subject to change without notice Page 10

Signal Descriptions

PETp(x)

PCI Express Transmit Positive signal of (x) pair.

PETn(x)

PCI Express Transmit Negative signal of (x) pair.

PERp(x)

PCI Express Receive Positive signal of (x) pair.

PERn(x)

PCI Express Receive Negative signal of (x) pair.

CREFCLK+/-

Cable REFerence CLocK: Provides a reference clock from the host system to the

remote system.

SB_RTN

Side Band ReTurN: return path for single ended signals from remote systems.

CPRSNT#

Cable PReSeNT: Indicates the presence of a device beyond the cable.

PWR

PoWeR: Provides local power for in-cable redriver circuits. Only needed on long

cables. Power does not go across the cable.)

PWR_RTN

PoWeR ReTurN: Provides local power return path for PWR pins.

CWAKE#

Cable WAKE

CPERST#

Cable PCI Express Reset

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de One Stop Systems

One Stop Systems

One Stop Systems PE3RR Manual de usuario

One Stop Systems

One Stop Systems OSS-PCIe-HIB2-EC-x1 Manual de usuario

One Stop Systems

One Stop Systems OSS-PCIe-HIB28-x16-H Manual de usuario

One Stop Systems

One Stop Systems OSS-412-BP Manual de usuario

One Stop Systems

One Stop Systems OSS-PCIe-HIB2-EC-x1 Manual de usuario

One Stop Systems

One Stop Systems ExpressBox 3T-V3 Manual de usuario

One Stop Systems

One Stop Systems OSS-PCIe-2U-ENCL-EXP-4-1 Manual de usuario

One Stop Systems

One Stop Systems Gen2 ExpressBox 16 - Smart Manual de usuario

One Stop Systems

One Stop Systems ExpressBox 3200 Manual de usuario

One Stop Systems

One Stop Systems OSS-PCIe-4U-EXP-2022-400 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario