Omron GI-S series Manual de usuario

CONFIDENTIAL © OMRON Corporation 0

GI-S series

How to configure a software IP address with a DHCP server

application

SPD-1809139 Rev.B

Introduction

When you add a GI-S to a network there are three ways to set the default IP address so you can

program the I/O Block.

1) Rotary switches

•Will set the IP address to 192.168.250.x. To do this set the rotary switches to 0xx where xx is the last octet in the

IP address.

2) DHCP

•Set the rotary switches to 000 or 400 (400 if you suspect the unit has an existing programmed IP address)

•Cycle power to the GI-S and it will pick up an address from the switch DHCP (if enabled on the switch)

•Use the switch software to determine what IP address the DHCP software on the switch gave to your device.

3) BOOTP-DHCP

•This is a Rockwell Automation tool that lets you assign a specific IP address to a specific MAC address.

•Set the rotary switches to 000 or 400 (400 if you suspect the unit has an exiting programmed IP address)

Note:

When you program the I/O block using Sysmac Studio you will set the device to a fixed IP address

as part of the setup and the DHCP or BOOTP-DHCP servers will no longer be needed. There is no

way to use Sysmac Studio to set the GI-S IP address without a Safety Controller being connected.

Hence the need for DHCP to get the GI-S on the same network as the Safety Controller.

Preparation

Necessary tools to use BOOTP-DHCP:

BOOTP-DHCP server ver 3.01.00 (Rockwell Automation):

BootP-DHCP allows you to assign a specific IP address to a specific MAC

address.

You can download here (Need to complete Account Registration):

https://rockwellautomation.custhelp.com/app/answers/detail/a_id/19793

Sysmac Studio:

Necessary to store software IP address into non-volatile memory.

Wireshark:

Only for troubleshooting (ex. In case you don’t know MAC address, you can’t

remember stored IP address).

https://www.wireshark.org/download.html

Preparation

Network configuration:

•PLC, target GI-S unit and Sysmac Studio PC must be in a network (accessible

directly) and have same network ID. See two examples below.

Using Port1: Using Port2:

192.168.1.1

DHCP client

(to be 192.168.1.2)

DHCP server

192.168.1.100

192.168.250.1

DHCP client

(to be

192.168.250.2)

DHCP server

192.168.250.100

NOTE:

Refer user’s manual Z400-E1 6-4-1 Setting the IP Address - IP

Addresses for detailed information network ID mechanism.

Step 1: Confirm MAC address of target unit

Confirm the MAC address on the label attached to the back of GI-S unit.

In this case, MAC

address is:

00:00:0A:BE:84:AC

Step 2: Find target unit

Run BOOTP-DHCP server tool and first configure the Network settings. No need to

fill numbers into all boxes. Typical requirement is set Subnet mask to

“255.255.255.0”.

Configure rotary DIP switches to “000” and power on. Wait for the MAC address of

target unit to appear in the list.

NOTE:

If you don’t see the target MAC address in the list, possible causes

are:

•Wrong rotary DIP switches setting.

•Firewall is blocking the BOOTP DHCP server.

•The target unit is already configured to work with software IP

address.

•Wiring issue (No power, Ethernet cable disconnected, etc.)

•Network configuration issue (GI-S is not directly accessible)

Step 3: Assign IP address

Click the line with target MAC address and select “Add relation”. Set the IP address to

assign the target unit. In this example it configured to “192.168.1.2” but any valid

number is available.

When it’s assigned, the IP addresses are shown in table above. At this point, the unit

uses the IP address but it’s not stored in non-volatile memory. If you reboot the unit

it sends DHCP request again.

NOTE:

This table shows the configured list of relationships between MAC

address and IP address.

Step 4: Store IP address

Use Sysmac Studio to store the software IP address to the target unit. In this example,

the safety connection configuration is already complete in the project. Log onto the

PLC and select target unit in Connection Settings, right-click and select “TCP/IP

Settings”. Fill the IP address into above box and click “Transfer”.

If you see the success message, the IP address is stored into non-volatile memory.

The unit works with stored IP address after power cycle.

NOTE:

Refer user’s manual Z400-E1, section 6-4-1 Setting the IP Address -

Built-in EtherNet/IP Port IP Address Settings –IP address setting

procedure - Fixing on the IP address obtained from the DHCP

server when the power is turned ON for detailed procedure.

Procedure for Multiple Targets

When IP addresses need to be assigned to multiple

target units.

Step 1: Assign IP addresses with csv file

BOOTP-DHCP server supports .csv file to import relationship

settings. Creating a table for multiple targets in a .csv file saves

time instead of manually assigning IP address one by one.

Click File > Open and import prepared .csv file.

Configure rotary DIP switches to “000” and power on all targets.

Wait for the MAC addresses of targets unit appears on the list

and IP addresses are assigned.

Otros manuales para GI-S series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de E/S de Omron

Omron

Omron DST1-ID12SL-1 Manual de usuario

Omron

Omron 3G3AX-MX2-EIO15-E Manual de usuario

Omron

Omron CJ1W-AD041-V1 Manual de usuario

Omron

Omron GRT1-ECT SmartSlice Manual de usuario

Omron

Omron C500-LDP01-V1 Manual de usuario

Omron

Omron CS1W-AD041-V1 Manual de usuario

Omron

Omron Sysmac CJ Series Manual de usuario

Omron

Omron NX-ID Manual de usuario

Omron

Omron NX-AD series Manual de usuario

Omron

Omron CS1W-CT021 Manual de usuario

Omron

Omron C120 Guía del usuario

Omron

Omron CJ1M-CPU21 Manual de usuario

Omron

Omron GX Series Manual de usuario

Omron

Omron W4S1-0 Series Guía de seguridad

Omron

Omron SYSMAC CS Series Manual de usuario

Omron

Omron SYSMAC C series Manual de usuario

Omron

Omron CP1W-TS102 Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

Omron

Omron CK3W-MD71 0 Series Manual de usuario

Omron

Omron C200H-DA002 Manual de usuario

Omron

Omron GI-S series Manual de usuario

Omron

Omron SmartSlice GRT1-Series Manual de usuario

Omron

Omron 3G3AX-EIO21-RE Manual de usuario

Omron

Omron NX Series Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario

Contec

Contec PIO-16L(PCI)H Manual de usuario