Oki MC770 series Manual de usuario

MC770 / MC770+ / MC780 / MC780+

MB760dn / MB770dnf / B721dn / B731dn

MPS3537mc / MPS3537mc+

MPS4242mc / MPS4242mc+

LCF Unit

Maintenance Manual

102213A

Disclaimer

Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-

date. The manufacturer assumes no responsibility for the results of errors beyond its control. The

manufacturer also cannot guarantee that changes in software and equipment made by other manufacturers and

referred to in this guide will not affect the applicability of the information in it. Mention of software products

manufactured by other companies does not necessarily constitute endorsement by the manufacturer.

While all reasonable efforts have been made to make this document as accurate and helpful as possible, we

make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information

contained herein.

The most up-to-date drivers and manuals are available from the web site:

http://www.okiprintingsolutions.com

45393301TH Rev.1 3 /

Oki Data CONFIDENTIAL

This manual explains the maintenance methods of LCF unit optionally installed in the MC760/

MC770/MC780/MB760dn/MB770dnf/B721dn/B731dn.

This manual is prepared for the maintenance person. In regard to the handling methods of

MC760/MC770/MC780/MB760dn/MB770dnf/B721dn/B731dn, please refer to the User’s

Manual.

Note! • Contentsofthismanualissubjecttochangewithoutnotice.

 • While all reasonable efforts have been made to make this document

as accurate and helpful as possible, we make no warranty of any kind,

expressed or implied, as to the accuracy of the information contained

herein. Oki Data assumes no responsibility to the damages caused or

claimedtohavebeencausedbytheuserasaresultofrepair,adjustment

and/or change using this manual.

 • Parts of this product are delicate and can be damaged unless properly

handled. We strongly recommend the user to maintain the product at the

hand of the registered maintenance person of our company

 • Beforestartingthemaintenancework,pleaseneutralizethestaticelectricity.

PREFACE

Oki Data CONFIDENTIAL

REPLACEMENT OF PARTS

This chapter describes the procedures of the ﬁeld replacement of parts, assemblies and units. The procedures are to detach them. Reverse

the procedures to attach them.

The reference part numbers used in this manual (such as and ) do not identical to the part numbers in the maintenance disassembly

conﬁguration diagram (45393301TL) and RSPL (45393301TR) for the manual.

1.1 Notes on replacement of parts ........................................................5

1.2 Part replacement procedure............................................................7

45393301TH Rev.1 5 /

Oki Data CONFIDENTIAL 1.REPLACEMENT OF PARTS

1.1 Notes on replacement of parts

(1) Prior to replacing a part, unplug the AC cord and the interface cable.

(a) Be sure to use the following procedure to unplug the AC cord:

Turn off the printer [the power switch to the off (O) position].

Pull out the AC plug of the AC cord from the AC power source.

Unplug the AC cord and the interface cable.

(2) Do not disassemble the printer so long as it operates properly.

(3) Minimize disassembly. Do not detach parts not shown in the part replacement

procedure.

(4) Use the replacement tools speciﬁed.

(5) Conduct disassembly in the order instructed, or part damage may occur.

(6) Removed small parts, such as screws or collars, should be tentatively installed in

their original positions.

(7) Do not use static-prone gloves when handling integrated circuits (ICs), including

microprocessors, and ROM and RAM chips, or circuit boards.

(8) Do not place printed-circuit boards (PCBs) directly on the printer or a ﬂoor.

Remo

Install

(b) Always use the following procedure to reconnect the printer:

Connect the AC cord and the interface cable to the printer.

Insert the AC plug into the AC power source.

Turn on the printer [the power switch to the on (I) position].

Warning

Electric shock hazard

When replacing the low-voltage power supply, electric shock may occur. Wear insulated

gloves, or be careful not to touch the conductors or terminals of the power supply directly.

After the AC cord is unplugged, the capacitor may take about one minute to discharge

completely or, due to PCB breakdown, could not discharge. Use caution about electric shock.

45393301TH Rev.1 6 /

Oki Data CONFIDENTIAL 1.REPLACEMENT OF PARTS

Maintenance Tools:

Table 1-1-1 shows the tools necessary to replace printed-circuit boards and units:

Table 1-1-1: Maintenance Tools

No. Maintenance Tool Quantity Use Remarks

Phillips

screwdriver with

magnetic tip, No.

2-200

13- to 5-mm

screws

2Screwdriver No.

3-100 1

3Digital multimeter 1

4Pliers 1

5E-ring pliers 1 E-shaped ring

removal

45393301TH Rev.1 7 /

Oki Data CONFIDENTIAL 1.REPLACEMENT OF PARTS

1.2 Part replacement procedure

This section describes the procedure for replacing the parts and assemblies shown in the

disassembly diagrams below.

1.2.1　Board-GOI,Frame.Assy-Hop etc

(1) Remove the Screw (silver,No:41723901) ①and remove the Joint ②(2 places),and

remove the LCF Unit ③from the MFP.

(This procedure unnecessary for B721/B731)

(2) Draw out the Cassette ④from LCF Unit.

④

⑦

⑧×2

⑨⑩

⑬

⑪

⑭

⑤×5

⑧

×2

⑫

⑮⑯×2

⑲×4

⑳㉑×2

㉒

⑥

⑤×5

㉓

㉖×2

㉗

㉔×4

㉕

⑰×2

⑱

①

②

③

(3) Remove the ten screws (silver,No:42920408) ⑤and remove the Cover-

Side(L) ⑥,Cover-Side(R) ⑦.

(If the LCF for B721/B731, remove the four screws)

(4) Remove the four screws (silver,No:42920408) ⑧and remove the Plate-

Joint(L) ⑨,Plate-Joint(R) ⑩.

(This procedure unnecessary for B721/B731)

(5) Remove the three screws (silver,No:42920406) ⑪and two screws

(black,No:44883906) ⑫and remove the Plate-Top ⑬.

(If the LCF for B721/B731, remove the seven screws (silver,No:42920406) and two

screws (black,No:44883906))

(6) Remove all cables ⑮and connectors from the Board ⑭.

(7) Remove the two screws (black,No:44883906) ⑯and remove the Board-GOI ⑭.

(8) Remove the two screws (silver,No:42920406) ⑰and remove the Plate-Front ⑱.

(9) Remove the four screws (black,No:44883906) ⑲and remove the Frame.Assy-

Hop ⑳.

(10) Remove the two screws (silver,No:43497603) 󰼼and remove the Connector 󰽇.

(11) Remove the Claw and remove the Switch 󰽈.

(12) Remove the four screws (black,No:44883906) 󰽉and remove the Liftup-Motor-

Assy 󰽊. Remove the two screws(silver,PSW2W2.6-5C)󰽋and remove the motor 󰽌.

45393301TH Rev.1 8 /

Oki Data CONFIDENTIAL 1.REPLACEMENT OF PARTS

1.2.2 Photo sensor　

(1) Remove the Frame.Assy-Hop（See 1.2.1）

(2) Remove the E-ring ①and remove the Hopping Clutch ②.

(3) Remove the three screws (silver,No:42920406) ③and remove the Plate-Assy-

Motor ④.

(4) Remove the two screws (silver,No:42920406) ⑤and remove the Motor ⑥.

(5) Remove the Gear-Z21-56 ⑦and Gear-Hopping ⑧and Bearing-Metal ⑨.

(6) Remove the Hopping roller ⑩and Pickup roller ⑪.

(7) Remove the two E-ring ⑫and pin ⑬and Gear-Feed ⑭.

(8) Remove the Bearing-Metal ⑮and Bush ⑯and remove the shaft ⑰.

(9) Remove the Frame-Assy-Pickup ⑱.(Pay attention to spring to lose)

(10) Remove the screw (Black,No:42932708) ⑲and remove the Plate-Hopping ⑳.

(11) Remove the claw and remove the photo sensor 󰼼.(Four places)

(12) Remove the E-ring 󰽇and remove the Regist Clutch 󰽈.

【Attention for assembling】

・

Wiring the white cable of the photo sensor to the mark ”W”of Guide-Hop.

　・When assembling the regist Clutch, same position the notch of the clutch and

bulge of the Plate-Motor.

　・

Wiring the cable of the Hopping clutch(Black cable) to the mark ”BK”of Plate-Motor.

When assembling the Hopping Clutch, same position the notch of the clutch and

bulge of the Plate-Motor.

　・When assembling the Motor, four emboss put into hole of Plate-Motor.The direction

of the Motor Cable should ” ↑”mark of Plate-Motor.

・To check the three claws and two claws of 󰽉is hold by ⑳.

㉑

③×3

②

①

⑲

⑳

④⑧

⑦⑰

⑨

⑪

⑩⑫

⑫

⑬

⑱

⑮

⑭

⑯

⑤×2 ⑥

㉒

㉓

㉔

spring

45393301TH Rev.1 9 /

Oki Data CONFIDENTIAL 1.REPLACEMENT OF PARTS

①

②×3

④

⑦×4 ⑧

⑨×1 2

⑪

⑩

⑪

⑩

⑫×2

⑬

⑫

×2 ⑬

⑭×2

⑮

⑭×2

⑮

⑯×3

⑰

⑤×3

⑥

③×6

1.2.3 Caster etc

(1) Draw out the Casstte ①,remove the six screws

（silver, D4-6HH）② and remove

the Cassette ①from LCF Unit.

(2) Remove the six screws

（silver, D4-6HH）③ and remove the Slide-Rail ④.

(2 places）

(3) Remove the three screws

（silver, No:42920406）⑤ and remove the Cover-

Front(LCF) ⑥.

(4) Remove the four screws

（silver, No:42920406）⑦ and Caster-Assy-Tray ⑧.

(5) Remove the twelve screws

（silver, No:42937208）⑨ and remove the two

Casters(with lock) ⑩ and remove the two Casters(without lock) ⑪. (Pay attention

to the position of caster, when assembling.)

(6) Remove the four screws

（silver, No:42937210）⑫ and remove the Cover-Leg-

Side ⑬.(2 places)

(7) Remove the four screws

（silver, No:42937210）⑭ and remove the Plate-Leg-

Assy ⑮.(2 places)

(8) Remove the six screws

（silver, No:42937210）⑯ and remove the Leg-Rear ⑰.

(2 places)

45393301TH Rev.1 10 /

Oki Data CONFIDENTIAL 1.REPLACEMENT OF PARTS

1.2.4 Pickup roller

If the hopping jam occurs frequently, to change the pickup roller and separation roller.

Model name： RS-C4B

separation roller spring

feed roler

(with gear)

pickup roler

(without gear)

Notes! •Ifchangetheroller,tochangeallrollers.

(1) Draw out the paper tray after the power off the printer.

aper Cassette

(2) Remove the latch and remove the roller ①,②

②

①

(3) Put the new roller

（with gear）① to the shaft.

①

Otros manuales para MC770 series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual