OHAUS Valor V11PW3 Manual de usuario

Valor™1000W Series

Instruction Manual

Serie Valor™1000W

Manual de Instrucciones

Série Valor™1000W

Guide de I’utilisateur

Serie Valor™1000W

Bedienungsanleitung

Serie Valor™1000W

Manuale d’instruzioni

OHAUS ValorTM 1000W Series EN-1

1. INTRODUCTION

This manual contains installation, operation and maintenance instructions for the

Ohaus ValorTM 1000W Series Scales. Please read the manual completely before

using the scale.

1.1 Safety Precautions

Please follow these safety precautions:

• Verify AC Adapter input voltage matches the local AC power supply.

• Do not immerse the scale in water or other liquids.

• Do not operate the scale in hostile environments.

• Do not drop loads on the platform.

• Do not place the scale upside down on the pan.

• Service should only be performed by authorized personnel

• Disconnect the scale from the power supply when cleaning

1.2 Controls

Figure 1-1. Controls.

4 5 6 7

Front displa

Rear displa

EN-2 OHAUS ValorTM 1000W Series

Figure 1-1. Controls (con’t).

TABLE 1-1. CONTROLS

Item Description

1 Battery charge indicator

2 Low battery indicator

3 Level Bubble

4 7-segment, 6-digit LED display

5 Center of Zero, Net, Stable, Sum, lb, kg indicators

6 Over, Accept, Under Checkweigh indicators

7 Control Buttons

8 Adjustable feet

9 Power input jack

TABLE 1-2. CONTROL FUNCTIONS.

Button Action Function

Short Press Turns scale on

Lon

Press Turns scale off

Menu function Shift to next digit when setting parameters, or step through

menu settings

Primary function Sets display to zero

Menu function Confirm settin

Long Press Enters menu mode

Menu function Save settin

s and exit the menu

Primary function Stores displayed weight in accumulation memory

Display accumulation data when display is at zero

Menu function Increment displa

ed value, or to

le throu

h menu settin

Primary function Tares weight of item on pan

Menu function Decrement displa

ed value, or to

le throu

h menu settin

OHAUS ValorTM 1000W Series EN-3

2. INSTALLATION

2.1 Package Contents

• ValorTM 1000W Scale

• Stainless steel Pan

• AC Power Adapter

• Instruction Manual

• Warranty Card

2.2 Location

Use the scale on a firm, steady surface. Avoid locations with excessive air current,

vibrations, heat sources, or rapid temperature changes. Adjust the leveling feet so

the bubble is centered in the circle.

Figure 2-1. Leveling the Scale.

2.3 Power

Connect the AC Adaptor to the AC mains supply. Connect the plug to the DC jack on

the bottom of the scale (see Figure 1-1, item 9). The scale may be operated on the

AC mains supply or the built-in rechargeable battery.

2.3.1 Battery Power

The scale will automatically switch to battery operation if there is a power failure or

the power cord is removed. With AC power, the scale is constantly charging, so the

battery charge indicator (see Figure 1-1, item 1) will remain lit. The scale can be

operated during charging, and the battery is protected against over charging.

Before using the scale for the first time, the battery should be fully

charged for up to 12 hours.

CAUTION: Battery is to be replaced only by an authorized Ohaus service

dealer. Risk of explosion can occur if replaced with the wrong type or

connected improperly. Dispose of the lead acid battery according to

local laws and regulations.

4 x Level Feet

Level Bubble

EN-4 OHAUS ValorTM 1000W Series

Note:

•Charging the scale must be performed in a dry environment.

•After charging, re-install the rubber seal to the power input jack (Figure 1-1, item

9) to ensure the scale is protected when operating in a wet environment.

3. OPERATION

3.1 Turning Scale On/Off

To turn the scale on, short press the On/Off button. The scale momentarily displays

software version, performs a display test then enters the active weighing mode.

To turn the scale off, long press the On/Off button.

3.2 Zero Operation

Zero is set under the following conditions (see Section 4.2 to select Initial Zero and

Key Zero ranges):

• Automatically at Power On (initial zero)

• Manually by pressing the ZERO button

Press ZERO to zero the stable weight display.

3.3 Manual Tare

Place a container on the weighing pan, then press TARE. The display will show a

net value of “0”. To clear the Tare value, press TARE with the pan empty.

3.4 Weighing Mode

Use this mode to measure the weight of a sample in the selected unit of measure

(see Section 4.2 to select unit). Press ZERO to set the display to zero. Put an empty

container on the pan as needed, then press TARE to tare the container weight. Add

material to the container. The display shows the weight of the material in the

selected unit of measure.

3.5 Sleep Mode

Whether on AC power or batteries, with the pan empty and the scale stable and

inactive for 1 minute, the display digits will turn off and show only a blinking

decimal.

OHAUS ValorTM 1000W Series EN-5

3.6 Accumulate Mode

Use this mode to store the weight and HI, LO, SUM statistics from a series of

samples.

• Press ZERO to set the display to zero.

• Place the item on the pan or tared container.

• Press M+ to store the weight of the item. Storage is confirmed by the display

[n----x], where x is the number of samples. The SUM LED will illuminate to

indicate there are readings in memory.

• Remove the item, wait for stable zero reading, then place the next item on the

pan. Press M+ to store the weight of the next item. Repeat this process until all

items have been weighed.

Review the accumulation data by pressing M+ when the display is at zero.

• The display shows the number of samples [n----x]

• Press M+ to view the maximum sample weight [Hxxxxx].

• Press M+ to view the minimum sample weight [Lxxxxx].

• Press M+ to view the sum of weights [xxxxx].

• Press M+ to return to weighing.

Clear the accumulated data by pressing ZERO when the number of samples [n----x]

is displayed.

Note:

• Only a total of 999 accumulated records [n 999] can be stored, and the sum

of the weights cannot exceed [999999]. [n OVEr] or [A OVEr] will be displayed

if these values are exceeded. Clear the Accumulate data to continue.

• Accumulated data is cleared when the unit of measure is changed.

3.7 Checkweigh Mode

Use this mode to compare samples to a target weight range (see section 4.1 to

activate and set limits).

Press ZERO to set the display to zero. Place a sample on the pan or tared container,

and read the displayed weight and under/accept/over status, where:

Under = weight is below preset minimum value

Accept = weight is equal to or within preset target range

Over = weight exceeds preset maximum value

Note: When the unit of measure is changed (see Section 4.2), checkweigh limits

and setting (see Section 4.1) will be reset to “0”.

EN-6 OHAUS ValorTM 1000W Series

4. MENU SETTINGS

Press and hold SET until [SEt-Fx] is displayed, where x:

0 = Set checkweigh limits and mode

1 = Set user settings

2 = Restore user settings to factory defaults

3 = Set tare capacity range

4.1 Checkweigh Over and Under Limits

•Press and hold SET until [SEt-F0] is displayed.

•Press YES to view the upper limit [000000] (or last value saved). The Over LED

will illuminate.

•Press h, j, ito edit the upper limit value (must be less than scale capacity).

•Press YES to confirm, then view the lower limit [000000] (or last value saved).

The Under LED will illuminate.

•Press h, j, ito edit the lower limit value (must be minimum of 20d scale

divisions, and less than upper limit).

•Press YES to confirm, then view the alarm setting [rUn x], where x:

0 = Checkweigh mode is disabled

1 = Checkweigh LEDs are active, beeper will sound when result is outside the

Accept range

2 = Checkweigh LEDs are active, beeper will sound when result is within the

Accept range

3 = Checkweigh LEDs are active, beeper is disabled

•Press hto step through available settings, then press YES to select.

•Press SET to save and exit.

Note: The measuring unit of the limit values will follow the active unit (see Section

4.2).

OHAUS ValorTM 1000W Series EN-7

4.2 User Settings

Press and hold SET, then huntil [SEt-F1] is displayed. Press YES to enter and view

user settings [F1-0 x]:

Parameters Description Settings of “x”

[F1-0 x] Key Zero Range 0 = 2% of scale capacity (default)

1 = 5% of scale capacity

2 = 10% of scale capacity

3 = 20% of scale capacity

[F1-1 x] Auto-zero Tracking Range 0 = 0ff

1 = 0.5d (d = scale division) (default)

2 = 1d

3 = 2d

4 = 3d

5 = 4d

6 = 5d

[F1-2 x] Initial Zero Range 0 = 10% of scale capacity (default)

1 = 20% of scale capacity

2 = 50% of scale capacity

3 = 100% of scale capacity

[F1-3 x] Unit of Measure 0 = kg (default)

1 = lb

[F1-4 x] Filter Level 0 = Low

1 = Medium (default)

2 = High

3 = maximum

[F1-5 x] Stability Indication 0 = Fast

1 = High (default)

2 = Medium

3 = Slow

[F1-6 x] Display Brightness 0 = Low

1 = Medium (default)

2 = High

3 = maximum

[F1-7 x] Accumulation Zero Band

(M+ is effective when stable

weight returns to within “x”)

0 = 0d (d = scale division) (default)

1 = within 1d

2 = within 2d

3 = within 5d

4 = within 10d

Press hto step through available settings.

Press YES to confirm displayed setting and proceed to next menu item.

Press SET at any time to save and exit.

EN-8 OHAUS ValorTM 1000W Series

4.3 Restore Settings to Default

Press and hold SET, then huntil [SEt-F2] is displayed. Press YES to enter and view

default user settings [F1-0 x].

Press YES to confirm displayed setting and proceed to next menu item.

Press SET to save and exit.

4.4 Set Tare Capacity

Press and hold SET, then huntil [SEt-F3] is displayed. Press YES to enter and view

tare capacity settings [tArE x], where x:

0 = 2/3 of scale capacity

1 = 100% of scale capacity

Press ji to toggle through available settings, then press SET to save and exit.

5. SCALE SETUP AND SPAN CALIBRATION

For best results, calibrate the scale at regular intervals. Temperature changes,

gravity variations and abuse are some reasons why a scale may need recalibration.

Enter calibration as follows:

•Turn the scale on.

•During the start-up display [000000…999999], press and hold SET until

[FS--SP] is displayed.

•Press YES to display [P x], where x = position of decimal point

•Press ji to toggle through settings: 0, 1, 2, 3, 4

•Press YES to select, then display [d x], where x = scale divisions

•Press ji to toggle through settings: 1, 2, 5, 10, 20, 50

•Press YES to select, then display scale capacity [xxxxxx] (kg)

•Press YES to select, then display [noLoAd]

•Make sure pan is empty, then press YES to display [LoAd]

•Press YES to select, then display default or last used span weight [xxxxxx] (kg)

•Press h, j, ito edit the displayed value (as needed)

•Place indicated weight on the scale, then press YES

•[CALEnd] is momentarily displayed to indicate calibration was successful, then

exit to weighing mode

•To abort calibration at any point, turn the scale off.

Examples:

Parameters: 3 x 0.0005 kg 6 x 0.001 kg 15 x 0.002 kg 30 x 0.005 kg 30 x 0.01 kg

P 4 3 3 3 3

d 5 1 2 5 10

Capacity 3.000 6.000 15.000 30.000 30.000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Escala de OHAUS

OHAUS

OHAUS FD Series Manual de usuario

OHAUS

OHAUS 1610 Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS Valor 2000W Series Manual de usuario

OHAUS

OHAUS Defender 3000 Manual de usuario

OHAUS

OHAUS PJX Series Manual de usuario

OHAUS

OHAUS Explorer EX125D Manual de usuario

OHAUS

OHAUS PR Series Manual de usuario

OHAUS

OHAUS Ranger 3000 Series Manual de usuario

OHAUS

OHAUS Valor 1000 Manual de usuario

OHAUS

OHAUS EXPLORER PRO Manual de usuario

OHAUS

OHAUS TA152 Manual de usuario

OHAUS

OHAUS Courier 7000 Manual de usuario

OHAUS

OHAUS Scout Pro Series Manual de usuario

OHAUS

OHAUS CHAMP II BASE Manual de usuario

OHAUS

OHAUS Adventurer AX224 Manual de usuario

OHAUS

OHAUS CS 200 Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS Catapult 1000 Manual de usuario

OHAUS

OHAUS DIAL-O-GRA 310 Manual de usuario

OHAUS

OHAUS JE 120 Manual de usuario

OHAUS

OHAUS Voyager Balances Manual de usuario

OHAUS

OHAUS Defender 6000 Indicators Manual de usuario

OHAUS

OHAUS ES series Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario