OHAUS Valor 1000 Manual de usuario

Valor 1000 Series

Instruction Manual

(Spanish)

(French)

(German)

(Italian)

EN-1OHAUS Valor 1000 Series

1. INTRODUCTION

This manual contains installation, operation and maintenance instructions for the

Ohaus Valor 1000 Series Scales. Please read the manual completely before using

the scale.

1.1 Safety Precautions

Please follow these safety precautions:

• Verify AC Adapter input voltage matches the local AC power supply.

• Do not immerse the scale in water or other liquids.

• Do not operate the scale in hostile environments.

• Do not drop loads on the platform.

• Do not place the scale upside down on the pan.

• Service should only be performed by authorized personnel

• Disconnect the scale from the power supply when cleaning

1.2. Controls

‘

Figure 1-1. Controls.

Item Description

1Low battery indicator

2Battery charge indicator

3Level Bubble

4Accumulate, NET, Stability Sum icons

5Over, Under , Accept Check weigh indicators

67-segment, 6 digit backlit LCD w/ units of measure enunciators

7Adjustable feet

8Power input jack

9On/ Off Power Switch

EN-2 OHAUS Valor 1000 Series

TABLE 1-2. CONTROL FUNCTIONS.

Button Action Function

ZERO

Enter

Short Press

Menu Press

Sets display to zero

Confirms settings

Short Press Tares weight of item on panTARE

ªMenu Press Decrement over and under settings

M+

Units

Short press:

Menu Press

Long Press

Stores displayed weight in accumulation memory

Display accumulation data when display is at zero

Increment over and under settings

Change unit of measure while long pressing SELECT

button

Short press: Shift to next digit when setting over and under valuesSELECT

Units

Long Press: Change unit of measure with short press of M+ button

2. INSTALLATION

2.1 Package Contents

• Valor 1000 Scale

• Stainless steel Pan

• AC Power Adapter

• Instruction Manual

• Warranty Card

2.2 Location

Use the scale on a firm, steady surface. Avoid locations with excessive air current,

vibrations, heat sources, or rapid temperature changes. Adjust the leveling feet so the

bubble is centered in the circle.

Level Bubble Level Feet

Figure 2-1. Leveling the Scale.

EN-3OHAUS Valor 1000 Series

2.3 Power

Connect the AC Adaptor to the AC mains supply. Connect the plug to the DC jack on

the bottom of the scale. The scale may be operated on the AC mains supply or the built

in rechargeable battery. The scale must be turned on to charge the battery.

DC Mains

Figure 2-2. Power Connection

2.3.1 Battery Power

The scale can be operated on the internal rechargeable battery when AC power is not

available. The scale will automatically switch to battery operation if there is a power

failure or the power cord is removed.

Before using the scale for the first time, the battery should be fully charged

for up to 12 hours. During charging, the battery Indicator displays the

charge level (see table 1-1), and the scale can be operated during

charging. The battery is protected against over charging and the scale can

remain connected to the AC power line.

NOTE:

• Charging the scale must only be performed in a dry environment

CAUTION: Battery is to be replaced only by an authorized Ohaus service

dealer

Risk of explosion can occur if replaced with the wrong type or connected

improperly

Dispose of the lead acid battery according to local laws and regulations

EN-4 OHAUS Valor 1000 Series

2.4 Initial Calibration

When the scale is operated for the first time, a Span calibration is recommended to

ensure accurate weighing results. Before performing the calibration, be sure to have the

appropriate calibration weight.

Refer to section 4.3 for Span calibration procedures.

3. OPERATION

3.1 Turning Scale On/Off

To turn the scale on, flip toggle switch below right front keyboard. The scale performs a

display test, momentarily displays software version, and then enters the active

weighing mode. To turn the scale off, toggle same switch to off position.

3.2 Zero Operation

Zero is set under the following conditions:

• Automatically at Power On (initial zero).

• Manually by pressing the ZERO button.

Press the ZERO button to zero the weight display. The scale must be stable and weight

+/- 2% of capacity to accept zero operation.

3.3 Manual Tare

Place a container on the weighing pan, then press TARE. The display will show a net

value of “0”. To clear the Tare value, press TARE with the pan empty.

3.4 Weighing Mode

Use this mode to measure the weight of a sample in the selected unit of measure.

Press and hold SELECT and press M+ Unit until the desired unit icon is displayed.

Press ZERO to set the display to zero. Put an empty container on the pan, and then

press TARE to tare the container weight. Add material to the container. The display

shows the weight of the material in selected unit of measure.

3.5 Accumulate Mode

Use this mode to store the weight and HI, LO, SUM statistics from a series of samples.

Press ZERO to set the display to zero.

Place the sample on the pan.

Press M+ to store the weight of the sample. Storage is confirmed by the display [n----

x], where x is the sample number. The enunciator above SUM text will illuminate to let

user know there are readings in memory. Remove the sample, wait for stable zero

reading, then place the next sample on the pan. Press M+ to store the weight of the

EN-5OHAUS Valor 1000 Series

next sample. Repeat this process until all samples have been weighed.

Review the accumulation data by pressing M+ when the display is at zero.

The display shows the number of samples [n----x]

Press M+ to view the maximum sample weight [Hxxxxx].

Press M+ to view the minimum sample weight [Lxxxxx].

Press M+ to view the sum of weights [xxxxx].

Press M+ to return to weighing.

Clear the accumulated data by pressing ZERO when the number of samples is

displayed.

3.6 Check Weigh Mode

Use this mode to compare samples to a target weight range.

Press ZERO to set the display to zero. Place a sample on the pan and read the weight

and under / accept / over status on display.

(Refer to section 4.1 to set limits)

3.7 Changing Units of Measure

Press and hold the M+ and SELECT buttons to display the next available measuring

unit.

4. SETTINGS

The scale allows the user to customize several settings including check weigh limits,

backlight operation and calibration.

4.1 Over and Under Limits

Press and hold ZERO and press SELECT until [SET---] is displayed.

Press SELECT to display [SET-F0]

Press ZERO to view the upper limit [000000].

Press §, ©, ªto edit the upper limit.

Press ENTER to confirm the setting and display the lower limit [000000].

Press §, ©, ªto edit the lower limit.

Press ENTER to confirm the lower setting and display will show Run---X where x is the

alarm setting. In this case x=

0 = Turns off check weigh mode

1 = under / accept / over indicators are displayed, alarm beeps when

weight is outside accept range.

2 = under / accept / over indicators are displayed, alarm beeps when

weight is within accept range.

3 = under / accept / over indicators are displayed, alarm is off.

EN-6 OHAUS Valor 1000 Series

Press SELECT to change the alarm setting.

Press ENTER to confirm setting and display [End]

Press and hold ZERO key then press SELECT to return to weighing.

4.2 Backlight

Press and hold ZERO button until [b9---x] is displayed, where x=

0 = backlight is turned off

1 = backlight is on during weighing

2 = backlight is always on

Press TARE to change the setting. Press ZERO to confirm the setting and return to

weighing.

4.3 CALIBRATION

Span Calibration:

Turn on the scale. When display flashes all segments ("888888") press and hold

ZERO and SELECT at the same time. "SET--- " will be displayed at the end of power on

sequence. Press the SELECT key until "SET-F1" is shown on the display.

Press ZERO key to display "A____x"(x=divisions in grams:1,2,5,10.20.50).

Press ZERO key to accept the default division setting which is shown on the display.

Press ZERO key to display "b____x"(x=decimal point:0,1,2,3). Press ZERO key to

accept the default decimal point setting which is shown on the display.

Press ZERO key to display "Cxxxxx"(xxxxx=Span weight or capacity of scale). Press

ZERO key to accept the default span calibration weight setting which is shown on the

display, or press M+ or TARE to increment or decrement the span calibration weight

setting.

Press ZERO to display "dx"(x=Zero tracking setting:0-9 from 0.125d to 2d). Press

ZERO key to accept the default setting which is shown on the display, or press M+ or

TARE to increment or decrement setting. Default setting is 3 which = 0.5d.

Press ZERO and display will show "Load 0". Make sure pan is empty then press ZERO

key to accept. Display will show "CAL 0" briefly, then "Load F” will be displayed.

Press ZERO to display "Fxxxxx"(xxxxx=Span weight ). Put displayed weight on the

scale, and press ZERO to accept. After completion, scale will be in weighing mode.

EN-7OHAUS Valor 1000 Series

5. MAINTENANCE

Caution: before cleaning, turn off the scale, remove the AC adapter.

5.1 Cleaning

The housing may be cleaned with a cloth dampened with a mild detergent if necessary.

Do not use solvents, chemicals, alcohol, ammonia or abrasives to clean the housing

or control panels.

5.2 Troubleshooting

The following table lists common problems and possible causes and remedies. If the

problem persists, contact Ohaus or your authorized dealer.

TABLE 5-1. TROUBLESHOOTING.

Symptom Possible Cause(s) Remedy

Scale will not turn on No power to scale

Battery power used up

Verify connections and voltage.

Connect power and charge the battery

Poor accuracy Improper calibration • Unstable

environment

Perform calibration • Move scale to

suitable location

Unable to calibrate Unstable environment

Incorrect calibration mass

Move the scale to suitable location

Use correct calibration mass

Scale flashes Bat Battery discharged Connect power and charge the battery

Battery fails to charge

fully

Battery is defective Have battery replaced by authorized

service dealer

-----H Pan has load during power on Remove weight from pan and re-zero

-----L Pan was removed Install pan and re-zero.

-Over- Weight on pan exceeds capacity Remove weight from the pan

Err-01 Invalid under and over limit settings Re-enter under and over limits

5.3 Service Information

If the troubleshooting section does not resolve or describe your problem, contact your

authorized Ohaus service agent. For service assistance or technical support in the

United States call toll-free 1-800-526-0659 between 8.00 AM and 5:00 PM EST. An

Ohaus product service specialist will be available to provide assistance. Outside the

EN-8 OHAUS Valor 1000 Series

USA, please visit our web site, www.ohaus.com to locate the Ohaus office nearest

you.

6. TECHNICAL DATA

The technical data is valid under the following ambient conditions:

Ambient temperature: 0°C to 40°C, Maximum Relative humidity: 80% for temperatures

up to 31°1C, decreasing linearity to 50% relative humidity at 40°C. Height above sea

level: Up to 2000m. Operability is assured at ambient temperatures between 0°C and

40°C Power: AC adapter – 9 VDC 500 mA output, Protection: Protected against dust

and water, Pollution degree: 2 , Installation category: Class III, EMC: See Declaration

of Conformity

6.1 Specifications

TABLE 6-1. Specifications.

Model V11P3 V11P6 V11P15 V11P30

Capacity (kg) 3 6 15 30

Readability (g) 0.5 1 2 5

Weigh Units Kilograms, Pounds, Grams, Ounces

Modes Weigh, Accumulate, Checkweigh

Keyboard Four Mechanical switches (Right)

Calibration Digital External Span Calibration

Display Type 6-digit 7-segment LCD with blue LED backlight

Display Indicators Center of zero, Stability, Net, Sum, Over/Accept/Under Check, Weighing

unit and Battery charge status

Display Size 20 mm / 0.8 in digits

Tare Range To capacity by subtraction

Stabilization Time <=3 seconds

Auto Zero Tracking User selectable from 0.1d to 2d

Operating Temp / Humidity 32°F to 104°F (0°C to 40°C) at 10% to 95% relative humidity

Non-condensing, up to 2.5 miles /4000m above sea level

Power 9 VDC 500 mA AC adapter (supplied)

Internal rechargeable sealed lead acid battery

Battery Life 80/100 hours (with/without backlight on)

Scale Dimensions (mm/in) 250w x 307d x 110h / 10w x 12d x 4.3h

Pan Size (mm/in) 250 x 180 / 9.9 x 7.1

Carton Dimensions (mm/in) 340w x 160d x 300h / 12.75w x 6.25d x 11.9h

Net Weight (kg/lb) 3.2/ 7

Shipping Weight (kg/lb) 4.0/ 8.8

EN-9OHAUS Valor 1000 Series

6.2 Compliance

Compliance to the following standards is indicated by the corresponding mark on the

product

Mark Standard

This product conforms to the EMC directive 2004/108/EC and the

Low Voltage Directive 2006/95/EC. The complete declaration of

Conformity is available from Ohaus Corporation

AS/NZS4251.1 Emission; AS/NZS4252.1 Immunity

Disposal

In conformance with the European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE) this device may not be

disposed of in domestic waste. This also applies to countries outside

the EU, per their specific requirements. Please dispose of this product in

accordance with local regulations at the collecting point specified for

electrical and electronic equipment. If you have any questions, please

contact the responsible authority or the distributor from which you

purchased this device.

Should this device be passed on to other parties (for private or

professional use), the content of this regulation must also be related.

Thank you for your contribution to environmental protection.

FCC Note

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Otros manuales para Valor 1000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de OHAUS

OHAUS

OHAUS Valor 2000W Series Manual de usuario

OHAUS

OHAUS BW1.5 Manual de usuario

OHAUS

OHAUS SJX1502N/E Manual de funcionamiento

OHAUS

OHAUS Guardian 3000 Manual de usuario

OHAUS

OHAUS ES series Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS Courier 1000 Manual de usuario

OHAUS

OHAUS i-D33P75SD Manual de usuario

OHAUS

OHAUS Scout SJX Manual de usuario

OHAUS

OHAUS YA Gold Series Manual de usuario

OHAUS

OHAUS PJX Series Manual de usuario

OHAUS

OHAUS Ranger Manual de usuario

OHAUS

OHAUS Adventurer Pro Grain Manual de usuario

OHAUS

OHAUS SCOUT Manual de usuario

OHAUS

OHAUS Valor 2000W Series Manual de usuario

OHAUS

OHAUS PX Series Manual de usuario

OHAUS

OHAUS Ranger RD Manual de usuario

OHAUS

OHAUS CS 2000 Manual de usuario

OHAUS

OHAUS valor 5000 series Manual de usuario

OHAUS

OHAUS Adventurer AX224N Manual de usuario

OHAUS

OHAUS Adventurer SL AS64 Manual de usuario

OHAUS

OHAUS Pioneer Manual de usuario

OHAUS

OHAUS CL Series Manual de usuario

OHAUS

OHAUS Defender D12RQR Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario