OHAUS BW Series Manual de usuario

Quick Start Guide BW Scales

Ohaus Corporation www.ohaus.com iBW Compact Bench Scales Quick Start Guide

PREPARATION FOR USE

Remove shipping protection screws on the

platform support, and plastic column inserts

under it. Re-install them if shipping the scale.

To minimize condensation inside the scale,

slightly loosen rear leveling feet; then level the

scale for normal operation. (Tighten all feet

when cleaning scale.)

To use AC power, remove rubber seal on

bottom to insert adapter plug in jack.

Battery charges when AC adapter is

connected. Scale switches to battery power if

AC power stops. Normal battery operating

time is 50 hours on a 15-hour charge.

Note: To prevent water ingress during use,

insert rubber Seal into the input jack recess.

SELECTING THE LOCATION

Place on a firm, steady surface.

Avoid locations with excessive air current,

vibrations, heat sources, or rapid temperature

changes.

Level the scale: Adjust leveling feet so bubble

is centered.

SAFETY PRECAUTIONS

For safe and dependable operation, observe the following safety precautions:

•Verify that indicated input voltage on Adapter and plug matches local power supply.

•Make sure that the power cord does not pose an obstacle or tripping hazard.

•Disconnect the product from the power supply when cleaning.

•Do not operate this product in hazardous or unstable environments.

•Do not drop loads on the pan.

•Use only approved accessories and peripherals, as available.

•Operate the product only under ambient conditions specified in the Instruction Manual.

•Service should be performed by authorized personnel only.

Plastic

column

inserts

Leveling

Feet

Shipping

protection

screws

BW Scales Quick Start Guide

BW Compact Bench Scales Quick Start Guide ii Ohaus Corporation www.ohaus.com

CONTROLS

• Turns the scale on

• Long-press turns the scale off

• In SETUP Mode, “Yes” accepts/confirms the displayed setting

• In CHECK Mode, accepts/confirms the displayed value

TARE

• Inputs the weight of the object on the weighing pan as a Tare value

• In SETUP Mode, “No” toggles through the available settings

• In CHECK Mode, increments the value of the selected digit

• Zeros the display

• With the scale off, long-press together with ON/OFF enters User Setup Mode

• In SETUP Mode, “Exit” ends setup and exits to “Save”

• In CHECK Mode, ends Over/Under setup and exits to weighing mode

• Initiates CHECK Over/Under setup

• In SETUP Mode, “Back” reverts to the previous parameter

• In CHECK Mode, shifts to the next digit

Center of zero

indicator

Battery charged

indicator

Active weighing unit indicator:

g– grams

–

Kilograms

Indicates displayed

weight is Under or Over

preset value

Low Battery

indicator

Net (Gross minus

Tare) indicator

Quick Start Guide BW Scales

Ohaus Corporation www.ohaus.com iii BW Compact Bench Scales Quick Start Guide

OPERATION

Turning Scale On/Off

Press ON. After a display test, scale enters active weighing mode.

Allow 15-30 minutes for warmup.

To turn the scale off, long-press Off.

Zero Operation

Press ZERO to zero the stable weight display.

(Weight must be within ±2% of scale capacity). Center of Zero indicator lights up.

Manual Tare

Place a container on the weighing pan and press TARE.

Display shows net value of “0”.

To clear Tare value, press TARE with pan empty.

TARE

Checkweigh Target Setting

Compares the weight of an item against a pre-set Over-Under range.

To activate Checkweighing Mode, see Menu – next page.

• Press CHECK to enter Over-Under parameters.

• Value of “OVER” target appears first, with active digit flashing. (OVER LED is lit.)

Press No to increment the active digit or CHECK to shift to the next digit.

• Press Yes to accept the displayed value and proceed to “UNDER” target.

Now the UNDER LED is lit.

TARE

• Press No to increment the active digit or CHECK to shift to the next digit.

• Press Exit to accept displayed value and exit into checkweighing mode.

Notes:

• OVER or UNDER LEDs light if weight on pan is over or under the pre-set limits.

• OVER and UNDER LEDs light simultaneously if weight is within pre-set limits.

• The LED indication is complemented by a beep.

• Over-Under values are retained when the unit is turned off.

• Over-Under values are not retained when the weighing unit or resolution setup are changed.

BW Scales Quick Start Guide

BW Compact Bench Scales Quick Start Guide iv Ohaus Corporation www.ohaus.com

Accessing the User Setup Mode

With the scale off, press ON/OFF and ZERO simultaneously.

When the scale turns on, release ON/OFF but keep pressing ZERO until SETUP appears

To navigate in the User Setup Mode, press:

to accept the displayed setting

to end setup and proceed to “Save”

to toggle through available settings

to revert to the previous parameter

User Setup Parameters

Parameters

Description Settings

Scale automatically turns off

after 15 minutes of inactivity.

ON - enables this function.

OFF -disables this function.

Scale enters sleep mode after

two minutes of inactivity.

ON - enables this function.

OFF -disables this function.

CHECK activation and

Alert Range

0 - Check mode is off.

Scale beeps when displayed weight is:

1–…within the preset Over and Under values

2–…outside the preset Over and Under range

3–…within the preset Over and Under values

(Over-Under LED’s do not light within preset range)

4–…outside the pre-set Over and Under range

(Over-Under LEDs do not light within preset range)

5– Alarm is off

(Over-Under LED’s do not light within preset range)

6– Alarm is off

Averaging Level 0, 1, 2, 3 (most filtering, longer stabilization time)

4, 5, 6, 7 (corresponds to 0, 1, 2, 3 but with slower

display update)

Weighing Unit Lb, oz, g

LED Brightness Level 0,1,2,3 (dimmest).

DSP

Display Type OFF – displays weight continuously.

ON – displays first stable weight.

Resolution OFF – 3000 scale divisions

ON – 6000/7500 scale divisions

Save

Save or Abort Save – saves changes and reverts to weighing mode.

Abort – reverts to weighing mode without saving

changes.

Note: Bold settings are defaults.

*80253134*

P/N 80253134

Otros manuales para BW Series

Tabla de contenidos

Otros manuales de Escala de OHAUS

OHAUS

OHAUS Scout STX Manual de usuario

OHAUS

OHAUS Ranger Count 3000 Series Manual de usuario

OHAUS

OHAUS DEFENDER D60ER Manual de usuario

OHAUS

OHAUS AV53 Manual de usuario

OHAUS

OHAUS Ranger Count Plus Manual de usuario

OHAUS

OHAUS ranger 7000 Manual de usuario

OHAUS

OHAUS 5000 Manual de usuario

OHAUS

OHAUS EXPLORER PRO Manual de usuario

OHAUS

OHAUS ES series Manual de usuario

OHAUS

OHAUS Valor 1000 Manual de usuario

OHAUS

OHAUS Explorer EX1241 Manual de usuario

OHAUS

OHAUS Scout pro Guía de instalación

OHAUS

OHAUS CS 2000 Manual de usuario

OHAUS

OHAUS CD-11 Manual de usuario

OHAUS

OHAUS SCOUT Manual de usuario

OHAUS

OHAUS PX Series Manual de usuario

OHAUS

OHAUS Compass CX221P Manual de usuario

OHAUS

OHAUS defender 7000 Manual de usuario

OHAUS

OHAUS BW1.5 Manual de usuario

OHAUS

OHAUS Compass CR221 Manual de usuario

OHAUS

OHAUS Courier 7000 Manual de usuario

OHAUS

OHAUS Valor 1000 Manual de usuario

OHAUS

OHAUS GT4100DG Manual de usuario

OHAUS

OHAUS Scout Series Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario