OHAUS Ranger 7000 Manual de usuario

RANGER®7000

Discrete I/O Interface

Instruction Manual

Manual de instrucciones

de la interfaz E/S discreta

de la RANGER® 7000

RANGER®7000

Interface E/S discrètes

Manuel d’instructions

RANGER® 7000

Diskrete I/O-Schnittstelle

Bedienungsanleitung

RANGER®7000

Interfaccia I/O discreto

Manuale di istruzioni

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Discrete I/O Interface EN-1

INTRODUCTION

This discrete I/O interface Kit is for use with the Ohaus Ranger®7000.

When installed, the system software allows the relay to be programmed in a variety of ways.

BASIC APPLICATIONS

Applications include: driving external Over/Accept/Under displays, motor controls for semi-automatic

filling systems, sorting systems, interfacing to industrial PLC systems, etc. The Relay outputs can

also be used as slave relays to drive high power relays in larger systems.

For the setup in each application, please refer to the instruction manual supplied with scale.

Set up the discrete I/O controls as described in the I/O menu section of that manual.

CAUTION: Read all safety warnings before installing, making connections, or

servicing the Discrete I/O PCB. Failure to comply with these warnings could result in

personal injury and/or property damage. Retain all instructions for future reference.

KIT CONTENTS

Cable Gland

Connector, 3 Pin

Screws (4)

Connector, 6 Pin

Cable to mainboard

I/O PC Board

INTERFACE INSTALLATION

CAUTION: THE INSTALLATION AND WIRE CONNECTIONS TO THE DISCRETE I/O

BOARD SHOULD ONLY BE DONE BY AUTHORIZED AND QUALIFIED

PERSONNEL, SUCH AS AN ELECTRICIAN.

WARNING: BEFORE MAKING CONNECTIONS TO THE RELAY TERMINALS,

POWER OFF THE SYSTEM AND REMOVE ALL EXTERNAL AC POWER

CONNECTIONS.

WARNING: WHEN MAKING ANY LINE VOLTAGE CONNECTIONS TO THE

DISCRETE I/O, FOLLOW NATIONAL ELECTRICAL CODE (NEC) OR LOCAL

AUTHORITY WIRING STANDARDS AND SAFETY PRACTICES.

Install the Interface module inside the terminal as shown.

Note: The appearance of your model may be different than that shown.

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

EN-2 Discrete I/O Interface

1. Disconnect the cable between base and terminal. Release the plastic plug by

using a Slotted screwdriver

2. Remove the four rubber pads.

3. Release the five screws

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Discrete I/O Interface EN-3

4. Install the Interface PCB. Push it through the pins and secure it with the 2

screws.

5. Install the cable gland, and pass the cable through it.

Connect the cable between the I/O board and the Main board.

Pins

Screws

Cable Gland

Cable to

Main board

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

EN-4 Discrete I/O Interface

6. Connect the cable to the two connectors (3 Pin and 6 Pin), and plug these two

connectors to the terminal block (J1 & J2).

7. Secure the cable gland and put the terminal cover back on.

IMPORTANT: When connecting any AC line supplied device to the Discrete I/O PCB,

ensure that each external device utilizes a properly grounded AC connection.

CAUTION: Do not operate the discrete I/O without the terminal cover in place

IMPORTANT: Review the I/O menu before using the discrete I/O board to control

external devices.

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Discrete I/O Interface EN-5

CONNECTION

INPUT

The discrete I/O interface enables other devices such as PLCs to provide the trigger voltage (typically

12 VDC or 24 VDC, maximum 30 VDC) to turn the inputs “on”.

An example of wiring to the inputs with the +V to the common is shown:

Note:

1. Voltage: 5~30 VDC, 10 mA maximum current. Voltage polarity cannot be reversed.

2. Do not bundle input wiring with power wiring or any other high energy cables.

3. Wire size: 18 AWG (0.832 mm2) maximum

24 AWG (0.205 mm2) minimum

OUTPUT

The four dry-contact normally open relay outputs can switch up to 250 VAC or 30 VDC voltages at 1A

maximum.

The relay outputs are not polarity-sensitive since they are dry contact outputs.

An example of wiring to the outputs is given below:

Notes:

1. Dry contact relays.

2. Relay contact rating:

AC: 24-250 VAC, 1.0 AMP. INTO resistive load.

DC: 5-45 VDC ,1.0 AMP. INTO resistive load.

Maximum switching power: 250VA, 30 W.

3. Maximum output circuit current = 3 AMPS.

4. All inductive loads must be suppressed.

5. Wire size: 18 AWG (0.832 mm2) Maximum

24 AWG (0.205 mm2) Minimum

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

EN-6 Discrete I/O Interface

COMPLIANCE

Disposal

In conformance with the European Directive 2002/96 EC on Waste Electrical and

Electronic Equipment (WEEE) this device may not be disposed of in domestic waste.

This also applies to countries outside the EU, per their specific requirements.

Please dispose of this product in accordance with local regulations at the collecting

point specified for electrical and electronic equipment. If you have any questions,

please contact the responsible authority or the distributor from which you purchased

this device.

Should this device be passed on to other parties (for private or professional use), the

content of this regulation must also be related.

For disposal instructions in Europe, refer to www.ohaus.com/weee.

Thank you for your contribution to environmental protection.

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Interfaz E/S discreta ES-1

INTRODUCCIÓ N

Este kit de la interfaz E/S discreta es para utilizar con la Ranger®7000 de Ohaus.

Al instalarlo, el software del sistema permite programar el relé de varias formas.

APLICACIONES BÁ SICAS

Entre las aplicaciones se incluyen: pantallas externas de exceso/aceptació n/defecto, controles del motor para los

sistemas de rellenado semiautomá tico, sistemas de clasificació n, sistemas de interconexió n para el PLC

industrial, etc. Las entradas de relé , pueden utilizarse como relé esclavo para utilizar relé s de alta potencia en

sistemas má s grandes.

Para la configuració n de cada aplicació n, consulte el manual de instrucciones que se suministra con la bá scula.

Configure los controles E/S como se describe en la secció n del menú E/S del manual.

PRECAUCIÓ N: Lea todas las advertencias de seguridad antes de la instalació n,

conexió n o reparació n del PBC de E/S discreta. No cumplir con estas advertencias

podría causar dañ os corporales y/o dañ os a la propiedad. Guarde las instrucciones

para futuras consultas.

CONTENIDO DEL KIT

Entrada del cable

Conector, 3 pines

Tornillos (4)

Conector, 6 pines

Cable a la placa base

Placa E/S para el ordenador

INSTALACIÓ N DE LA INTERFAZ

PRECAUCIÓ N: LA INSTALACIÓ N Y CONEXIÓ N DEL CABLE A LA PLACA E/S

DISCRETA SOLO DEBE REALIZARLA PERSONAL AUTORIZADO Y CUALIFICADO,

COMO POR EJEMPLO UN ELECTRICISTA.

ADVERTENCIA: ANTES DE CONECTAR LOS TERMINALES DEL RELÉ , APAGUE

EL SISTEMA Y QUITE LAS CONEXIONES DE CORRIENTE ALTERNA EXTERIOR.

ADVERTENCIA: AL CONECTAR LAS LÍNEAS DE ALTA TENSIÓ N A LA E/S

DISCRETA SIGA EL CÓ DIGO ELÉ CTRICO NACIONAL (NEC) O LAS NORMAS

LOCALES DE CABLEADO Y LAS PRÁ CTICAS DE SEGURIDAD.

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

ES-2 Interfaz E/S discreta

Instale el mó dulo de la interfaz en el interior del terminal como se muestra.

Nota: La apariencia de su modelo puede ser diferente a la que se muestra.

1. Desconecte el cable entre la base y el terminal. Libere el enchufe de plá stico

mediante un destornillador de pala plana.

2. Quite las cuatro almohadillas de goma.

3. Quite los cinco tornillos.

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Interfaz E/S discreta ES-3

4. Instale el PBC de la interfaz. Empú jelo contra las patillas y asegú relo con los 2

tornillos.

5. Instale la entrada del cable y pase el cable a travé s de la misma.

Conecte el cable entre la placa de E/S y la placa base.

Patillas

Tornillos

Entrada del

cable

Cable a

placa base

info@GlobalScientificSupply.com

www.GlobalScientificSupply.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Otros manuales para ranger 7000

Tabla de contenidos

Idiomas:

Otros manuales de Escala de OHAUS

OHAUS

OHAUS ES6R Manual de usuario

OHAUS

OHAUS Scout STX Manual de funcionamiento

OHAUS

OHAUS HH 320 Manual de usuario

OHAUS

OHAUS Pioneer PX85 Manual de usuario

OHAUS

OHAUS Courier 3000 Manual de usuario

OHAUS

OHAUS Adventurer AX224N Manual de usuario

OHAUS

OHAUS Compass CX Series Manual de usuario

OHAUS

OHAUS EX224 Manual de usuario

OHAUS

OHAUS PS Series Manual de usuario

OHAUS

OHAUS YJ103 Manual de usuario

OHAUS

OHAUS Scout STX Manual de usuario

OHAUS

OHAUS VE Series Manual de usuario

OHAUS

OHAUS Catapult 1000 Manual de usuario

OHAUS

OHAUS 1119-DO Manual de usuario

OHAUS

OHAUS VF Series Manual de usuario

OHAUS

OHAUS EB3 Manual de usuario

OHAUS

OHAUS Compact Series Manual de usuario

OHAUS

OHAUS SCOUT II Manual de usuario

OHAUS

OHAUS TROOPER SCALE Manual de usuario

OHAUS

OHAUS SD Series Manual de usuario

OHAUS

OHAUS EC Series Manual de usuario

OHAUS

OHAUS CS 200 Manual de usuario

OHAUS

OHAUS Defender 2000 Manual de usuario

OHAUS

OHAUS SD Series Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

OHAUS ranger 7000 Manual de usuario

Manuales populares de Escala de otras marcas