NuWaves NUPOWER S100A01 Manual de usuario

USER MANUAL

NUPOWERTM S100A01

S-BAND POWER AMPLIFIER

PART NUMBER:

NW-PA-S-100-A01

NuWaves Engineering

132 Edison Drive

Middletown, Ohio 45044

PH: 513-360-0800

FAX: 513-539-8782

www.nuwaves.com

product.sales@nuwaves.com

NuPower

S100A01 User Manual

Rev 1.0

1NUPOWERTM PRODUCT LINE OVERVIEW

The NuPower family of solid state RF power amplifier (PA) modules is designed to meet the demanding

needs of the Aerospace & Defense, Industrial, and Commercial markets. Based on the latest gallium

nitride (GaN) technology, NuPower’s power efficiency and miniature form factor make it ideal for size,

weight, and power-constrained broadband RF telemetry and tactical communications systems.

1.1 NUPOWERTM PRODUCT LINE HIGHLIGHTS

•High Performance: Unique combination of broadband coverage, miniature form factors, and

high efficiency.

•Enclosures: The NuPower family of power amplifiers are housed in a silver nickel plated

aluminum enclosure with mounting holes incorporated into the chassis.

•Completely Characterized: The NuPower family of solid-state power amplifiers have been

completely characterized over temperature, voltage, and frequency. These high-performance

modules offer significant value for the OEM user or the Systems Integrator.

•User Friendly: Over-Voltage protection and regulator thermal shutdown provide defenses

against user interface issues.

•High Reliability: NuWaves’ selection of conservatively rated components provides high

reliability. Each NuPower is inspected to IPC-A-610 Class II quality standards. NuWaves’ Quality

Management System is AS9100:2016 Rev D and ISO 9001:2015 certified.

•Applications: Broadband RF Telemetry • RF Communication Systems • Electronic Warfare •

Unmanned Aircraft Systems (UAS) • Unmanned Ground Vehicles (UGV) • Unmanned Surface

Vehicles (USV) • Software Defined Radios • Test Labs

•Available Options:

oFan-cooled heat sink with 28V operated fan

oLabeled interface cable with banana jack plugs

NuPower

S100A01 User Manual

Rev 1.0

2NUPOWERTM S100A01 PA OVERVIEW

The NuPowerTM S100A01 PA is a highly efficient, solid state power amplifier that typically provides 125

Watts of RF power across 2000 MHz – 2500 MHz.

Based on the latest gallium nitride (GaN) technology, NuPower S-Band power efficiency and < 10 in3

cubic inch form factor make it ideal for size, weight, and power-constrained broadband RF telemetry

and tactical communication systems.

The NuPowerTM S100A01 ruggedized chassis allows the system integrator to easily incorporate the unit

into a platform operating in harsh environments with limited space, such as small Unmanned Aircraft

Systems (UAS).

Figure 1: NuPower S100A01 Functional Diagram

NuPower

S100A01 User Manual

Rev 1.0

2.1 NUPOWER S100A01 PA SPECIFICATIONS

The subsequent tables in this section outline the NuPower S100A01’s performance specifications.

Table 1: NuPower S100A01 Electrical Specifications

Parameter Specification

Frequency Range 2000 MHz to 2500 MHz

RF Output Power 90 Watts (min); 125 Watts (typ)

Output Power @ 1 dB Compression

36 dBm @ 2000 MHz

37 dBm @ 2250 MHz

41 dBm @ 2500 MHz

RF Large Signal Gain 21 dB (typ)

Input VSWR 1.5:1 (typ)

Output Mismatch Max

(No Damage all Phase Angles) 10:1

Nominal Input Drive Level +30 dBm

Maximum Input Drive Level

(No damage) +33 dBm

Harmonics

2nd: ≤-52 dBc

3rd: ≤-55 dBc

Third Order Intercept Point

(Two tone test at 1 MHz spacing,

Pout = 30 dBm / tone)

46 dBm @ 2000 MHz

47 dBm @ 2250 MHz

49 dBm @ 2500 MHz

Switching Speed 2 µS (max), 500 ns (typ)

Operating Voltage +27 to +32 VDC

Operating Current 11.5 A @ +28 VDC (typ)

Module Efficiency 40% (typ)

Power Amplifier Enable RF Enable = Low (0V – +0.8VDC)

Impedance 50 Ω

NuPower

S100A01 User Manual

Rev 1.0

Table 2: NuPower S100A01 Environmental Specifications

Operating Conditions Specification

Operating Temperature -40 to +45 oC (ambient)1

-40 to +70 oC (baseplate)2

Storage Temperature -55 to +85 oC

Table 2 Notes:

145°C max ambient operating temperature with HTSK-07; Pout = 100W

270°C max baseplate operating temperature (S100A01 module only); Pout = 100W

Table 3: NuPower S100A01 Mean Time Between Failure (MTBF)

Conditions Hours

Ground Benign (GB) 292,657

Airborne Inhabited Cargo (AIC) 14,955

Airborne Inhabited Fighter (AIF) 11,976

Airborne Uninhabited Cargo (AUC) 4,994

Airborne Uninhabited Fighter (AUF) 4,108

NuPower

S100A01 User Manual

Rev 1.0

2.2 NUPOWER S100A01 PA MECHANICAL SPECIFICATIONS

Figure 2: NuPower S100A01 Mechanical Outline

Table 4: NuPower S100A01 Mechanical Specifications

Parameter Specification

RF Connectors SMA (female)

Control / Power Interface Connector Micro-D Hybrid, 7+2-pin

Socket

Dimensions (L x W x H) 6.5” x 4.5” x 1.0”

Weight 22.6 oz.

NuPower

S100A01 User Manual

Rev 1.0

2.3 HEAT SINKING

The NuPower S100A01 is offered as a stand-alone module or with an optional heat sink

(p/n: HTSK-07), which includes a 28 VDC fan-cooled heatsink and requisite power cable.

Caution: The use of external heat-sinking is required especially for those applications

requiring high duty cycle operation (e.g. continuous wave) or for extended on-time testing.

Operation without a proper heat sink under these conditions will cause permanent damage

to the product and will void the product warranty.

The maximum operating temperature of the module only is 70˚ C (baseplate).

3SETUP AND OPERATION

This section provides specific details for proper operation of the NuPower S100A01 module. Following

these guidelines will prevent damage to the power amplifier or external equipment.

3.1 POWER SUPPLY REQUIREMENTS

To operate the NuPower S100A01, ensure that the power supply has adequate overhead to source the

current demand of the RF power amplifier. The power supply source must provide a typical voltage of

+28 VDC with greater than 13 amps capability.

3.2 CONNECTING A PROPER LOAD TO THE ANTENNA TERMINAL

To prevent damage to the PA, the antenna terminal must be terminated into a 50 Ω load. Examples of a

proper load include:

•Directly connecting to an antenna specified for the frequency range (2000 MHz to 2500 MHz).

Connecting to an inappropriate antenna may result in damage to the PA module.

•Connecting to a proper antenna through a 50Ω transmission line or coaxial cable. Avoid using

damaged cables or corroded connectors while attaching the unit to an antenna.

•Terminating the antenna terminal into a 50Ωhigh power attenuator with minimum 20 dB

attenuation.

•Connecting to a load capable of dissipating the RF power from the PA module. Loads capable of

handling 200 Watts (min) are recommended.

3.3 POWERING-UP THE NUPOWER S100A01

The NuPower S100A01 must be terminated to a proper load before power is applied. Refer to Section

3.2 for the specifications of the proper load. After the PA is properly terminated, the interface cable can

be connected to the unit and power can be applied. The PA is now ready for operation.

NuPower

S100A01 User Manual

Rev 1.0

3.4 TRANSMIT TURN-ON TIME

The NuPower S100A01 is at full power approximately 500ns after the RF Enable line goes low (ground).

Therefore, transmit data can be applied to the input after 500ns without loss of data.

4HARDWARE INTERFACE

•The RF Input connector is SMA (female).

•The RF Output connector is SMA (female).

•The pin-out definitions for the Micro-D Hybrid, 7 +2-pin socket connector are provided in Table

5. In a typical installation, the PA module is mated to a host controller board via a cable harness.

The RF Out SMA

connector is the antenna connection. This connection should

always be loaded into 50 Ω, otherwise the PA could be damaged.

4.1 INTERFACE CABLE HARNESS

The cable harness that connects the host controller to the Micro-D Hybrid, 7 +2-pin socket connector of

the NuPower S100A01 is made up of 9 wires.

Table 5: NuPower S100A01 Interface Pin-Out Definitions

Pin No. Pin Name I/0 Description

A2 DC Power

(+28V)

I Primary Power (+28 VDC)

3, A1 GND I Signal and Power Ground

2 Over

Temperature

Flag

O +5V TTL Logic Level

0V = Temperature Fault

+5V = No Fault

1 RF Enable I Transmit Control:

RF Enable Floating = RF Off

RF Enable Logic Low (0V- +0.8V) =

Bias Enabled

4 Current Temp O Analog voltage calibrated to

internal temp

5 N/C N/A No Connect

NuPower

S100A01 User Manual

Rev 1.0

Figure 3: Micro-D Hybrid, 7 +2-pin Socket Locations

*Do not connect the Temperature Flag to DC Power (+28 Volts input). The Temperature Flag can be used

to monitor thermal status.

4.2 DC POWER

The nominal supply voltage for the NuPower S100A01 is +28 VDC. The acceptable supply voltage range

is +26 to +32 VDC. If a voltage above 32VDC is applied, the drain bias to internal amplifiers will be

removed and the transmit path will be non-operational.

4.3 GROUND

The signal and power grounds are tied together in the PA module.

4.4 RF ENABLE

This signal is the logic control input that designates whether the unit is in transmit or standby mode. The

RF Enable line is pulled high internally placing the PA module in standby mode. If the pin is left floating

(i.e. not connected), the unit will default to standby mode.

Grounding the pin (i.e. a voltage below +0.8 VDC) places the unit in transmit mode. The user can either

connect the RF Enable line to pins A1 or 3 on the CTRL/PWR interface connector, or an open drain logic

line capable of sinking 500 µA to place the unit in transmit mode.

Do not connect the RF Enable line to DC Power (+28 Volts input). No input voltage is required on the RF

Enable line.

NuPower

S100A01 User Manual

Rev 1.0

4.5 TEMP FLAG

This signal is an output to indicate an over-temperature condition in the NuPower S100A01. A logic high

(+5 VDC) indicates normal operation, while a logic low (0 VDC) indicates an over-temperature condition.

The NuPower S100A01 incorporates internal logic circuitry that turns off the DC bias to the RF

amplifiers. See section 4.6 for details on thermal shutdown points.

Caution: The amplifier should be shut down and allowed to cool off when the over-

temperature flag is set low to avoid damage to the module.

Do not connect the Temperature Flag to DC Power (+28 Volts input). The Temperature Flag

can be used to monitor thermal status.

4.6 CURRENT TEMP

This signal is an output to indicate internal temperature of the S100A01. Temperature Flag (Section 4.5)

threshold is reached when internal temperature of approximately 85°C is exceeded and will re-enable

bias to internal RF amplifiers at approximately 70°C. See Figure 5 below for ‘current temp’ voltage and

corresponding internal temperature.

Figure 5. Current Temperature Output Voltage vs. Internal Temperature

200

250

300

350

400

450

500

550

600

650

700

750

800

850

900

950

1000

1050

1100

-40 -35 -30 -25 -20 -15 -10 -5 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85

Current Temp Voltage (mV)

Internal Temperature (°C)

Current Temp Voltage vs. Internal Temperature

Current Temp (mV)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de NuWaves

NuWaves

NuWaves NuPower 12B01A Manual de usuario

NuWaves

NuWaves NUPOWER XTENDER C10RX03 Manual de usuario

NuWaves

NuWaves NUPOWER L60T01 Manual de usuario

NuWaves

NuWaves NW-PA-12B01A Manual de usuario

NuWaves

NuWaves NuPower Xtender 12B04A Manual de usuario

NuWaves

NuWaves HILNA-HF-AGC Manual de usuario

NuWaves

NuWaves NUPOWER 12B01A-D30 Manual de usuario

NuWaves

NuWaves NUPOWER C30R01 Manual de usuario

NuWaves

NuWaves NUPOWER 12B01A-02 Manual de usuario

NuWaves

NuWaves NUPOWER XTENDER VU4GX01 Manual de usuario

NuWaves

NuWaves NUPOWER XTENDER 12B04A-D30 Manual de usuario

NuWaves

NuWaves NUPOWER 11B02A-TAC Manual de usuario

NuWaves

NuWaves NuPower 12D05A Manual de usuario

NuWaves

NuWaves HILNA LS-C026 Manual de usuario

NuWaves

NuWaves HILNA LS-C021-D Manual de usuario

NuWaves

NuWaves HILNA GPS Manual de usuario

NuWaves

NuWaves NuPower C20R01 Manual de usuario

NuWaves

NuWaves NUPOWER XTENDER C10RX01 Manual de usuario

NuWaves

NuWaves NUPOWER ULS-25-C01-S01 Manual de usuario

NuWaves

NuWaves NuPower 05E05A Manual de usuario

NuWaves

NuWaves NuPower 11B02A-TAC2 Manual de usuario

NuWaves

NuWaves NUPOWER XTENDER LS10S01 Manual de usuario

NuWaves

NuWaves XTENDER VU4GX02 Manual de usuario

NuWaves

NuWaves NUPOWER 15D05A-C01-S01 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario