Norac UC5 Topcon X30 Manual de usuario

Spray Height

ontroller

John Deere

GS2

2600 and 1800

All Pull Types Display Kit

Installation Manual

GS2

PT01

Printed in Canada

Reorder P/N: 54VT-GS2-PT01-INST Rev A (John Deere GS2 2600 and 1800 All Pull Types

Display Kit)

NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without

the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information contained in this

manual. The technical information in this manual was reviewed at the time of approval for publication.

Contents

1INTRODUCTION...................................................................................................2

1.1 List of Parts....................................................................................................................................... 2

2INSTALLATION ....................................................................................................3

2.1 Control Module on Tractor................................................................................................................. 3

2.2 Control Module on Sprayer................................................................................................................ 4

2.3 Switch Box Installation...................................................................................................................... 5

3CABLE DRAWINGS..............................................................................................6

3.1 ITEM C25: 44602-01 – SWITCH REMOTE HAND CONTROL...................................................... 6

3.2 ITEM C26: 43240-26 – CABLE UC5 SWITCH BOX....................................................................... 7

3.3 ITEM C30: 43250-06 – CABLE UC5 BATTERY PIGTAIL............................................................. 8

3.4 ITEM C41: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M...................................................... 8

3.5 ITEM C40: 43260-02 – CABLE UC5 CAN BUS VT JD GS2 ........................................................... 9

APPENDIX A: ALTERNATE CONFIGURATION ................................................10

1 Introduction

The John Deere GS2 2600 and 1800 – All Pull Types Display Kit Manual is intended to be used

in conjunction with the UC5 Spray Height Control Installation Manual. This manual provides

instructions to interface the UC5 Control Module to the John Deere GS2 2600 and 1800

Displays. For installation of the rest of the UC5 Spray Height Control System please refer to the

sprayer specific manual provided with the kit.

1.1 List of Parts

Item Part Number Name Quantity

C25 44602-01 BOX SWITCH UC4 REMOTE HAND CONTROL VER.1 RMR 1

C26 43240-26 CABLE UC5 SWITCH BOX 1

C30 43250-06 CABLE UC5 BATTERY PIGTAIL (FUSED) 1

C40 43260-02 CABLE UC5 CAN BUS VT JD GS2 1

C41 43220-03 CABLE UC5 NETWORK 14 AWG 3M 1

E12 43764 UC5 NETWORK COUPLER 2-WAY 1

M01 UC5-BC-MANUAL - NS MANUAL UC5 OPERATORS - NORAC 1

M04 54VT-GS2-PT01-INST MANUAL UC5 DISPLAY KIT JOHN DEERE GS2 2600 & 1800 - ALL PULL TYPES 1

2 Installation

The following instructions are for installation on a pull type sprayer. On a pull type sprayer if

the CAN-bus and power supply are located on the sprayer, the control module may also be

installed on the sprayer (Section 2.2). This type of installation would eliminate the need for a

cable across the hitch.

2.1 Control Module on Tractor

1. Securely mount the control module (E01) inside the tractor cab.

2. Tee the CAN-bus interface cable (C40) in to the John Deere CAN-bus. Connect the 6 pin

Deutsch plug on cable C40 to the end of the control module with only one Deutsch

connector.

3. Connect cable C41 to the other CAN-bus connector and route the cable to the hitch of the

tractor.

4. Connect the two-way coupler (E12) to the end of cable C41.

5. Connect cable C01 to the coupler (E12) and route towards the rear of the sprayer. The two-

way coupler (E12) will provide the hitch disconnect.

Figure 1: GS2 2600 Display Kit – Control Module on Tractor

2.2 Control Module on Sprayer

1. Securely mount the control module (E01) on the sprayer near the CAN-bus connection.

2. Tee the CAN-bus interface cable (C40) in to the John Deere CAN-bus. Connect the 6 pin

Deutsch plug on cable C40 to the end of the control module with only one Deutsch

connector.

Figure 2: GS2 2600 Display Kit – Control Module on Sprayer

2.3 Switch Box Installation

1. This step of the installation assumes that the input module and all required cables are

installed.

2. Disconnect cable C20 (Thru 2 connector) from the Input Module (E03). Remove the wedge

from the face of the 12 pin Deutsch plug. The wedge is removed by inserting a small flat

implement underneath the wedge and lifting it up.

3. Insert the Roll CW pin from C26 into position 3 of the 12 pin plug on C20. Insert the Roll

CCW pin from C26 into position 4 of the 12 pin plug on C20. Insert the wedge back into the

plug. Connect C20 to the Thru 2 connector on the Input Module.

4. Connect the 12 pin Deutsch plug on C26 to the OEM 3 connector on the input module.

Route the other end of the cable to the hitch of the sprayer.

5. Attach the switch box (C25) inside the cab and connect it to cable C26. An extra label is

provided with the switch box if you prefer to remove the switches from the housing and

mount them in the existing sprayer switch panel.

* Some sprayer types may not use all the switch functions.

* Refer to “Appendix A” for sprayers with European style slant control.

Figure 3: Switch Box Installation

3 Cable Drawings

3.1 ITEM C25: 44602-01 – SWITCH REMOTE HAND CONTROL

3.2 ITEM C26: 43240-26 – CABLE UC5 SWITCH BOX

3.3 ITEM C30: 43250-06 – CABLE UC5 BATTERY PIGTAIL

3.4 ITEM C41: 43220-03 - CABLE UC5 NETWORK 14 AWG - 3M

Otros manuales para UC5 Topcon X30

Tabla de contenidos

Otros manuales de Controladores de Norac

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC5 Topcon X30 Manual de usuario

Norac

Norac UC5-BC-JD11 Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC5 Topcon X30 Manual de usuario

Norac

Norac UC5 Topcon X30 Manual de usuario

Norac

Norac UC5 Topcon X30 Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC5 Topcon X30 Manual de usuario

Norac

Norac Gregson Maverick 120 Series Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC4+ Case 44 Series Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC5 Topcon X30 Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC5 Topcon X30 Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC4 Plus Rogator 64 Series Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC4+ Manual de usuario

Norac

Norac UC4+ Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario