Nibe FLM Guía del usuario

IHB EN 1850-5

331702

INSTALLER MANUAL

Exhaust air module

NIBE FLM

LEK

41 Important information

4Safety information

62 Delivery and handling

6Transport

6Assembly

7Supplied components

7Removing the covers

83 The design of the exhaust air module

9Pipe connections

9HVAC components

9Sensors etc.

9Electrical components

9Ventilation

9Miscellaneous

104 Pipe and ventilation connections

10General pipe connections

11Dimensions and pipe connections

11Mounting

12Brine side

13Condensation water hose

14General ventilation connection

14Ventilation flow

14Adjusting ventilation

14Dimension and ventilation connections

15Installation alternative

175 Electrical connections

17General

17Connections

226 Commissioning and adjusting

22Preparations

22Filling and venting

23Start-up and inspection

267 Program settings

26Start guide

26Menu system

288 Service

28Service actions

299 Disturbances in comfort

Info menu

29Manage alarm

30Troubleshooting

3110 Accessories

3211 Technical data

32Dimensions and setting-out coordinates

33Technical specifications

34Electrical circuit diagram

36Item register

39Contact information

3Table of ContentsNIBE FLM

Table of Contents

Safety information

This manual describes installation and service proced-

ures for implementation by specialists.

The manual must be left with the customer.

This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given super-

vision or instruction concerning use of the

appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Rights to make any design or technical

modifications are reserved.

©NIBE 2018.

SYMBOLS

NOTE

This symbol indicates danger to person or ma-

chine .

Caution

This symbol indicates important information

about what you should consider when installing

or servicing the installation.

MARKING

The CE mark is obligatory for most products sold in

the EU, regardless of where they are made.

Classification of enclosure of electro-technical equip-

ment.

IP21

Danger to person or machine.

Read the User Manual.

SERIAL NUMBER

The serial number can be found at the bottom left inside

the front cover.

LEK

Serial number

Caution

You need the product's (14 digit) serial number

for servicing and support.

RECOVERY

Leave the disposal of the packaging to the in-

staller who installed the product or to special

waste stations.

When disposing of the product, its constituent

materials and components, e.g. compressors,

fans, circulation pumps and circuit boards, must be dis-

posed of at a special waste station or dealer who

provides this type of service.

To access the separate components, refer to the section

that shows the construction of the product. No special

tools are required for access.

Improper disposal of the product by the user results in

administrative penalties in accordance with current le-

gislation.

NIBE FLMChapter 1 | Important information4

1 Important information

INSPECTION OF THE INSTALLATION

In addition, fill in the page for the installation data in the User Manual.

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must

be carried out by a suitably qualified person. Current regulations require the exhaust air module to be inspected

before it is commissioned. The inspection must be carried out by a suitably qualified person. In addition, fill in the

page for the installation data in the User Manual.

DateSignatureNotesDescription

✔

Ventilation (page 14)

Setting the ventilation flow

Brine (page 12)

Non-return valve

System flushed

System vented

Antifreeze

Expansion vessel

Particle filter

Safety valve

Shut off valves

Circulation pump setting

Checking the condensation water seal

Trim valve

Electricity (page 17)

Connections

Phase voltage

Supply connected 230 V

Circuit fuses

5Chapter 1 | Important informationNIBE FLM

Transport

The exhaust air module should be transported and stored

in the dry.

Assembly

NIBE FLM is installed on top of the ground heat pump

or freestanding on brackets. Noise from the circulation

pump or fan can be transferred to the brackets.

•Install with its back to an outside wall, ideally in a room

where noise does not matter, in order to eliminate

noise problems. If this is not possible, avoid placing

it against a wall behind a bedroom or other room

where noise may be a problem.

• Wherever the unit is located, walls to sound sensitive

rooms should be fitted with sound insulation.

• Route pipes so they are not fixed to an internal wall

that backs on to a bedroom or living room.

INSTALLATION AREA

Leave a free space of 800 mm in front of the product.

Leave free space between NIBE FLM and wall/fit-

tings/cables/pipes etc. It is recommended that a space

of at least 10 mm is left to reduce the risk of noise and

of any vibrations being propagated.

800

NOTE

Ensure that there is sufficient space (300 mm)

above NIBE FLM for installing ventilation

hoses.

NIBE FLMChapter 2 | Delivery and handling6

2 Delivery and handling

Supplied components

Non-return valve (RM1)

Ø 32 mm

LEK

Trim valve (RN1)

Ø 15 mm

2 x screws (T25) for in-

stalling NIBE FLM on NIBE

heat pump

LEK

Condensation water hose

Ø 20 mm

LOCATION

The bag of supplied items is placed on top of NIBE FLM.

Removing the covers

FRONT COVER

1. Remove the service cover by pulling it straight out.

LEK

SIDE COVERS

1. Undo the screws at the upper edge

2. Lift the side hatches upwards and twist the cover

outwards slightly.

3. Assembly takes place in the reverse order.

LEK

7Chapter 2 | Delivery and handlingNIBE FLM

LEK

S3 AA5-S2 AA5

AA5

SF3 AA5-S2

LEK

PF1 HQ10 AA100 BT21

BT20 QM21 XL32

XL31

XL32 BT20

HQ10

XL31

AA100

QM21

PF 1

BT21

LEK

W7 W1 XL40

SF1SF2

SF2 SF1

XL40W6

LEK

EP16 GQ2 GP2

XL6 XL7BT27

BT26

GQ2EP16

XL6 XL7

GP2

BT26 BT27

NIBE FLMChapter 3 | The design of the exhaust air module8

3 The design of the exhaust air

module

Pipe connections

Connection, brine in, compression ring Ø 15 mmXL6

Connection, brine out, compression ring Ø 15 mmXL7

Ventilation connection exhaust air, Ø 160 mmXL31

Ventilation connection extract air, Ø 160 mmXL32

Drip-pan drainXL40

HVAC components

Heat exchangerEP16

Circulation pump, brineGP2

Venting brineQM21

Sensors etc.

Temperature sensor, exhaust airBT20

Temperature sensor, extract airBT21

Temperature sensor, collector inBT26

Temperature sensor, collector outBT27

Electrical components

Accessory cardAA5

Dip switchAA5-S2

Joint cardAA100

Switch, position 0 - 1, main switchSF1

Switch, position 0 - 1, circulation pumpSF2

PotentiometerSF3

Cord with connection plugW1

Control cableW6

Ventilation

Exhaust air fanGQ2

Exhaust air filterHQ10

Miscellaneous

Type platePF1

Designations at component positions according to standard EN 81346-

9Chapter 3 | The design of the exhaust air moduleNIBE FLM

General pipe

connections

Pipe installation must be carried out in accordance with

current norms and directives.

Lowest permitted temperature of incoming brine is -8°C.

Pipes and other cold surfaces must be insulated with

diffusion-proof material to prevent condensation.

SYMBOL KEY

MeaningSymbol

Shut-off valve

Non-return valve

Circulation pump

Expansion vessel

Filterball

Fan

Pressure gauge

Safety valve

Trim valve

Manual reversing valve/shunt

Bore hole

Ground collector

OUTLINE DIAGRAM

-QZ20

NOTE

Venting may be necessary during installation

and after a period of use. Venting takes place

through vent valve (QM21). When venting, set

the switch for the circulation pump (SF2) to

position ”0”.

COMPATIBLE NIBE HEAT PUMPS

NIBE FLM ventilates the building and preheats the brine,

regardless of which ground source heat pump is in-

stalled, but when NIBE FLM is installed together with

a compatible ground source heat pump, it is possible to

adjust settings and read off sensor values etc. in the

heat pump’s display.

Compatible products

• F1345

• F1355

• F1245

• F1255

• F1145

• F1155

NIBE FLMChapter 4 | Pipe and ventilation connections10

4 Pipe and ventilation

connections

Otros manuales para FLM

Tabla de contenidos

Otros manuales de Unidad de control de Nibe

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario