NGS ROLLER JOY Manual de usuario
roller JOY
USER’S MANUAL
www.ngs.eu
English iFrançais iEspañol i Deutsch iItaliano i Português iPolski i
ΕΛΛΗΝΙΚΑ
roller JOY
bluetooth stereo speakeR
ENGLISH
OVERVIEW
1 Mode/bluetooth button
2 Volume – / previous
3 Volume + / next
4 button
5 Charging LED
6 Connected LED
7 Battery
8 Micro SD card slot
9 USB port
10 On/Off
11 Connection point for
charging via micro USB
1 5 6 8 97 10 1132 4
USER’S MANUAL
BLUETOOTH SPEAKER PAIRING
RECONNECTING
1. Turn on the power, a message sound; “beep” will
announce from speaker and the mode LED will blinking
in blue; the device is turned ON and goes into searching /
paring / reconnect mode for pair.
2. Now, turn ON the Bluetooth function on your mobile
phone.
3. Search for “NGS ROLLER JOY” and select it to pair (for
first time pairing or pairing a new mobile device).
4. The Bluetooth speaker will be reconnecting
automatically if your mobile phone has been
paired (Depend on the of mobile phone’s type and
configuration, manual reconnection may require on
some devices).
CHARGING THE BLUETOOTH
SPEAKER
1. Connect the Bluetooth speaker’s micro USB socket with
the computer’s USB port through USB cable.
2. The charging LED will turn ON in red light; the
rechargeable battery is in charging.
3. The charging LED red light will turn OFF when the
rechargeable battery is fully charged.
4. Disconnect the USB cable.
ENGLISH
BLUETOOTH SPEAKER CONTROL
FUNCTION
1. In playing music, press button to pause music,
press it once again to play.
2. Press and hold the button to increases the volume
level.
3. Press and hold the button to decreases the
volume level.
4. Press the button to play next music file.
5. Press the button to play previous music file.
MODES
BLUETOOTH / LINE IN / MICRO SD CARD / USB / FM RADIO
To switch between modes, press the key. If the device
is not connected to a micro SD card or USB memory, it will
skip these modes.
5. If pairing is successful, a message sound; “beep” will
announce from speaker and the mode LED light will
keep turn on.
USER’S MANUAL
MICRO SD CARD MODE
1. Insert the micro SD card or a USB flash drive into the
slot.
2. The device will automatically play any music in MP3
format on the card or USB flash drive.
HAND FREE FUNCTION
BLUETOOTH MODE ONLY
When there is an incoming call;
1. The ringing sound will up and the playing music will
pause automatically.
2. Press button to pick up the call if you want.
3. Now you have hand free function with the Bluetooth
speaker.
4. Hold down the button for 2 seconds to hand up
the call when finished. And,
5. The paused music will start to play automatically.
LINE IN MODO
1. Connect the audio source to the speaker via a micro USB
audio cable.
2. Play music from external audio source.
Note: Not all functions are available in LINE IN mode. Only
volume function is available.
ENGLISH
If at any time in the future you should need
to dispose of this product please note that:
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist.
Check with your Local Authority or retailer
for recycling advice.
(Waste Electrical and Electronic Equipment
Directive)
HEREBY, LURBE GRUP S.A, DECLARES
THAT THIS SPEAKER IS IN COMPLIANCE
WITH THE ESSENTIAL REQUIREMENTS
AND OTHER RELEVANT PROVISIONS OF
DIRECTIVE 1999/5/EC.
FM MODE
1. Hold down the button and the device will cycle
between modes until you hear the message “FM RADIO
MODE”.
2. Press the button for automatic channel search.
Once the search is finished, skip between channels by
pressing the and buttons.
Note: For better radio reception, connect the charging
cable (which also acts as an antenna) into the micro USB
slot.
Battery warranty: The battery is a consumer product, and
as such it is under warranty for 12 months.
roller JOY
Haut-parleur bluetooth stéréo
FRANÇAIS
APERÇU GENERAL
1 Bouton mode/bluetooth
2 Volume – / précédent
3 Volume + / suivant
4 Bouton
5 LED de charge
6 LED de connexion
7 Batterie
8 Entrée carte micro SD
9 Port USB
10 Allumé/éteint
11 Connexion charge micro
USB
1 5 6 8 97 10 1132 4
MANUEL DE L’UTILISATEUR
COUPLAGE RECONNEXION DU
HAUTPARLEUR BLUETOOTH
1. Allumez l’alimentation, un message est diffusé par le
haut-parleur et le voyant LED bleu du mode clignote ;
le dispositif s’allume et passe au mode de recherche /
couplage / reconnexion pour réaliser le couplage.
2. Activer maintenant la fonction Bluetooth sur votre
téléphone mobile.
3. Rechercher le “NGS ROLLER JOY” et le sélectionner pour
effectuer le couplage (pour le premier couplage ou pour
le couplage d’un nouveau dispositif mobile).
4. Le haut-parleur Bluetooth rétablira automatiquement
la connexion à votre téléphone mobile si celui-ci a été
couplé précédemment (cela dépend du type et de la
configuration du téléphone mobile, certains dispositifs
peuvent requérir la reconnexion manuelle).
CHARGEMENT DU HAUT
PARLEUR BLUETOOTH
1. Raccorder la prise micro USB du haut-parleur Bluetooth
au port USB à l’aide du câble USB.
2. Le voyant LED rouge de charge s’allume; la batterie
rechargeable est en cours de chargement.
3. Le voyant LED rouge de charge s’éteint; la batterie
rechargeable est complètement chargée.
4. Débrancher le câble USB.
Tabla de contenidos
Idiomas:
Otros manuales de Oradores de NGS
NGS
NGS SKYLINE Manual de usuario
NGS
NGS ROLLER ROCKET Manual de usuario
NGS
NGS ROLLER BYRON 360 Manual de usuario
NGS
NGS Roller Flow Mini Manual de usuario
NGS
NGS WILD DUB ZERO Manual de usuario
NGS
NGS SKYDUSk Manual de usuario
NGS
NGS ROLLER SLANG Manual de usuario
NGS
NGS Roller Cube Manual de usuario
NGS
NGS ROLLER PINEAPPLE Manual de usuario
NGS
NGS WILDSKA1 Manual de usuario
NGS
NGS WILDTRAP 3 Manual de usuario
NGS
NGS WILDPUNK Series Manual de usuario
NGS
NGS SKY CHARM Manual de usuario
NGS
NGS ROLLER STREAM Manual de usuario
NGS
NGS WILDMAMBO Manual de usuario
NGS
NGS ROLLER CREEK Manual de usuario
NGS
NGS WILDDANCE Manual de usuario
NGS
NGS roller Trick Manual de usuario
NGS
NGS roller flash Manual de usuario
NGS
NGS WILDDISCO Manual de usuario
