New lift FST Guía

Installation & Commissioning

Field Bus Control

FST_MIA.DE10/98

Publisher NEW LIFT Steuerun

sbau GmbH

Adi-Maislin

er-Straße 12

D-81373 München

Tel.: +49

(

)

89 / 74 35 44 - 0

Fax: +49

(

)

89 / 769 34 85

Doc. No. FST_MIA.DE10/98

Date of issue 10/98

sbau GmbH

All ri

hts, includin

those of cop

or of reproducin

parts of this

description and of the translation are reserved b

the publisher.

No part of this description ma

be reproduced in an

form or copied with an

electronic replication s

stem, without the written permission of the

publisher.

Table of contents

FST_MIA.DE10/98 3

1 About this manual .............................................................................................. 5

1.1 General information.................................................................................................. 5

1.2 Signs and symbols employed.............................................................................. 6

2 General safety provisions ............................................................................. 9

2.1 Qualifications of the installing engineer.......................................................... 9

2.2 Residual dangers..................................................................................................... 10

2.3 Safety provisions..................................................................................................... 10

3 Assembly work ...................................................................................................13

3.1 Installation sequence............................................................................................. 13

3.2 Bus Plan...................................................................................................................... 15

3.3 Scope of delivery..................................................................................................... 16

3.4 Control cabinet......................................................................................................... 18

Installin

the control cabinet............................................................................................ 18

Connectin

the control cabinet........................................................................................ 19

Startin

up the control cabinet......................................................................................... 20

Technical details.............................................................................................................. 21

3.5 Car components....................................................................................................... 25

Installation locations of the car components.................................................................... 25

Installin

car components................................................................................................ 26

Connectin

car components............................................................................................ 27

Commissionin

the car components ............................................................................... 28

Technical details - FPM car operatin

panel module ..................................................... 29

Technical details - FSM car control module .................................................................... 31

3.6 Installing and connecting the trailing ribbon cable.................................. 33

3.7 The installation run................................................................................................. 35

Connectin

the LON bus................................................................................................. 37

Installin

zone switches and ma

nets............................................................................. 38

Installin

and settin

the linear cop

control............................................................... 40

Table of contents

4FST_MIA.DE10/98

4 Commissioning the FST Control ...........................................................43

4.1 Commissioning sequence ................................................................................... 43

4.2 User interface of the FST Control..................................................................... 44

The display ...................................................................................................................... 45

The keyboard................................................................................................................... 47

The LEDs......................................................................................................................... 48

4.3 Commissioning the linear copying control .................................................. 49

Checking the direction of rotation of the absolute value encoder.................................... 49

Checking flush position with A6 Safety Monitoring Device.............................................. 50

Checking flush position with A6 Safety Monitoring Device.............................................. 51

4.4 Carrying out a calibration drive......................................................................... 53

4.5 Commissioning the A6 Safety Monitoring Device..................................... 57

4.6 Setting control options.......................................................................................... 58

Crawl drive....................................................................................................................... 58

Password......................................................................................................................... 58

Door times ....................................................................................................................... 59

Group operation............................................................................................................... 60

5 Event and fault messages ...........................................................................61

5.1 LED messages on the user interface .............................................................. 61

5.2 Error list....................................................................................................................... 62

5.3 Event messages....................................................................................................... 64

5.4 Error messages........................................................................................................ 65

6 Terminal and pin assignment ...................................................................69

Trailing ribbon cable ........................................................................................................ 69

LON bus........................................................................................................................... 72

VSM preselection module................................................................................................ 72

FSM car control module.................................................................................................. 72

7 Index ...........................................................................................................................73

1 About this manual

FST_MIA.DE10/98 5

1 About this manual

Before installin

and startin

upthe FST Control,

oushould carefull

read

this manual first. The instructions in Chapter 2 “General safet

provisions”

alwa

s take precedence. How to operate the FST Control is outlined in

Chapter 4.2 “User interface of the FST Control”.

1.1 General information

This manual is intended to facilitate the assembl

and commissionin

the FST Control and its components.

Thisassembl

and operatin

manualcontains importantinstructionsforthe

safe and proper assembl

and commissionin

of the FST Control.

Observing them helps to:

- avoid dan

ers

- minimise repair costs and downtime

- increase the reliabilit

and service life of the FST Control and the lift

stem.

In addition to this assembl

and operation manual, the valid accident

prevention and environmental protection re

ulations in the respective

countr

and localit

must be observed.

Onl

those sub-assemblies supplied b

NEW LIFT are described in this

manual.

Information about components of the control s

stem not produced and

supplied b

NEW LIFT can be obtained from the user documentation

provided b

the respective manufacturer or supplier.

1 About this manual

6FST_MIA.DE10/98

1.2 Signs and symbols employed

The following signs and symbols have been used for operational

instructions:

Symbols ➤Activity symbol:

The activities described after this sign should be carried out in the

prescribed sequence.

✔Outcome symbol:

The outcome of an activity is described.

+Key combination:

Press the linked keys simultaneously.

Warning signs General danger point

This sign appears before activities where personal injuries may

arise due to various causes.

Risk of crushing injuries

This sign appears in front of activities where there is a danger

of receiving crushing injuries.

Danger of falling

This sign appears in front of activities where there is a danger

of falling.

Suspended load

This sign appears in front of activities where there is a danger

of direct impact from a falling load.

1 About this manual

FST_MIA.DE10/98 7

High voltage

This si

n appears in front of activities where there is a dan

of an electric shock, with possibl

fatal conse

uences.

Material damage

The instructions provided here are intended to prevent an

material dama

e to sub-assemblies and devices.

1 About this manual

8FST_MIA.DE10/98

2 General safety provisions

FST_MIA.DE10/98 9

2 General safety provisions

All the most important safet

provisions and re

ulations are compiled in the

Chapter 2 “General safet

provisions”.

Anybody who is assigned to work on the installation and

commissioning of the FST Control, must have read this chapter and

put its provisions into practice.

Over and above an

safet

provisions specified in this manual, the laws,

ulations,

uidelines and standards in force in the respective countr

should be observed.

2.1 Qualifications of the installing engineer

The installin

ineer must:

- be 18

ears of a

e or older

(

exception: trainees of 16

ears or older,

under the constant supervision of a master craftsman

)

- be able to carr

out first aid.

- know and be able to implement the fire and explosion protection

ulations applicable for his work area.

-beabletoreco

nise, avoid and protect himself a

ainst all the dan

ers

arisin

in con

unction with his work in the lift shaft and in the operatin

areas.

- be able to identif

and rectif

all irre

ularities and faults arisin

durin

installation and operation of an lift s

stem.

- understand and be able to appl

the technical basis of the mode of

operation of electrical controls and drive s

stems and their operatin

uirements.

All installation and commissionin

work on the electrical and electronic

components of the FST Control are to be carried out under the direction

and supervision of a

ualified electrician.

In German

, someone is defined as a

ualified electrician, who due to his

technical trainin

, knowled

e and experience and ac

uaintance with the

relevant provisions, is able to evaluate the work assi

ned to him and to

identif

the possible dan

ers

(

UVV, VGB 4, §2

(

))

2 General safety provisions

10 FST_MIA.DE10/98

2.2 Residual dangers

Danger for personnel Risk of electrocution on touching parts under voltage during work on the

electrical installations.

Risk of fatal injuries due to falling down the lift shaft.

Risk of injuries when lifting and transporting the switch cabinet if this falls

or tips over.

Risk of dangers to persons, who are in the lift shaft when the car is in

motion.

Risk of injuries due to unforeseen car movements.

Risk of material damage Destruction of the FST Control and its electronics modules by short

circuiting or excess loading.

2.3 Safety provisions

General information The instructions of the manufacturer and the information in this manual

must be observed when the lift is being installed and commissioned.

The lift shaft must be secured against unauthorised access during

installation and commissioning.

Sub-assemblies, devices and cables should be installed securely and

permanently.

Loads should be transported with suitable aids (e.g. lift trucks, lifting gear

etc.).

Sharp or pointed tools or other potentially dangerous objects may not be

carried in clothing, unless protected by sufficient protective measures.

The consumption of alcohol and drugs before and during installation and

commissioning is forbidden.

Otros manuales para FST

Tabla de contenidos

Otros manuales de Controladores de New lift

New lift

New lift FST-2 Manual de usuario

New lift

New lift FST-2XT MRL Guía

New lift

New lift FST-2s Manual de usuario

New lift

New lift FST-2XT MRL Manual de usuario

New lift

New lift FST Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario