Netum NT-W8 Manual de usuario
R
► USB wired + 2.4G wireless communication
► Built-in FLASH memory, supports breakpoint resume
► Can store 2600 pieces Code-128 codes under offline state
► Supports Windows XP, Win7/8, Wince, mobile OS PC
Quick Start Guide
Packing list:
Barcode scanner x 1 pc
USB cable x 1pc
2.4G receiver x 1pc
Quick Start Guide x 1pc
Note: The device is not equipped with the charger, please charge the
device via USB output charging equipment.
2.4G Wireless Barcode Scanner Overview
Netum 2.4G wireless model integrates a high-performance processer with an effective decoding
board, combining a fast decoding speed. High precision and a high anti-interference ability in one
device. The device can easily read barcodes on paper and other surface.
2.4 GHz Wireless
USB2.0 Wired
Factory Default Configuration
This confirguration including four steps,Please scan below codes one by one .
· Step 1 : Factory default · Step 2 : Enable Code 39
303FFF3 1000111
· Step3 : Serial Port · Step 4 : Baud Rate 19200
3030010 2090107
Note that there will not have a beep sound after you scan code of “default configuration”.
As long as light turns off a few seconds before you release the trigger button that means scanner
has read the codes successfully. keep scanning the following codes until last one to finish the
default configuration.
1
Scanning Mode
Note that there will not have beep sound when you set below modes.
As long as light turns off a few seconds before you release the trigger button that
indicate the configuration has been done.
· Key Holding
Press the button to trigger the reading, release the button to end the reading.
Reading success or reading time over a single reading time will end the reading
· Continuous Mode
The reading engine performs continuous work. Reading success or reading time
over a single reading time will end the reading. More than the specified time will
automatically trigger the next reading.
· Automatic Induction Mode
In automatic induction mode, the scan engine detects the brightness of the
surroundings. Trigger reading when the brightness changes. Reading success or
reading time over a single reading time will end the reading. Regardless of the last
success or failure to read, re-enter the detection of the surrounding environment
brightness.
2050200
2050204
2050209
2
Below configurations only apply for wireless model
If you are heading for a working area which lies outside the signal range, you may
activate the offline mode of the scanner, following the steps described below. Under
this enhanced offline mode, all scanned data will be stored directly into the buffer
memory of the device. Furthermore, the data entries will be permanently saved in
the buffer memory prior to the manual upload into the working station, so that you
may upload them time and again to your liking. Due to the fact that the data entries
will be automatically wiped from the buffer memory during upload, a data loss is
possible when malfunctions occur during uploading.
1. By scanning the following barcode, the offline mode will be activated.
Offline mode activation
Clear all Storage
Manual data upload
2. By scanning the following barcode, all data in the buffer memory will be deleted
(only in offline mode).
3. By scanning the following barcode, all data entries in the buffer memory can be
manually uploaded after reconnecting to the working station (only in offline mode).
Summarising of uploaded data entry quantity
4. By scanning the following barcode, the gross quantity of the uploaded data entries
will be summarised (only in offline mode).
3
Quit offline mode
5. By scanning the following barcode, the device leaves the offline mode, normal
mode will be reinitialised.
Add character format: Decode Data + Terminator.
A prefix and/or one or two suffixes can be appended to scan data for use in data
editing. To set these values, scan a four-digit number (i.e. four bar codes) that
corresponds to ASCII values. See the Table 4-3 and Numeric Bar Codes in
appendix. To change the selection or cancel an incorrect entry, scan Cancel in
appendix. To set the Prefix/Suffix values via serial commands, see Setting Prefixes
and Suffixes Via Serial Commands.
NOTE In order to use Prefix/Suffix values, the Scan Data Transmission Format
must be set.
Terminator configuration
Prefix/Suffix Values
3030050
Disable
3030051
CR & LF
3030052
CR
3030053
TAB
50C0107
Scan Prefix
50C0006
Scan Suffix 1
4
50C0208
Scan Suffix 2
20C1000
*Data As Is
20C1001
<DATA><SUFFIX 1>
20C1002
<DATA><SUFFIX2>
20C1003
<DATA> <SUFFIX 1><SUFFIX 2>
20C1004
<PREFIX> <DATA >
20C1005
<PREFIX> <DATA> <SUFFIX 1>
20C1006
<PREFIX> <DATA> <SUFFIX 2>
20C1007
<PREFIX> <DATA> <SUFFIX 1> <SUFFIX 2>
To change the Scan Data Transmission Format, scan one of the eight bar codes
corresponding to the desired format
Scan Data Transmission Format
5
0 1
23
4. Appendix
Numeric Bar Codes
For parameters requiring specific numeric values, scan the appropriately
numbered bar code(s).
6 7
89
45
Cancel
To change the selection or cancel an incorrect entry, scan the bar code below
Cancel
6
50C0107
Scan Prefix
50C0006
Scan Suffix 1
Step 2 and Step 3 same procedures like setting prefix
Step 4: Set Data Transmission Format
20C1004
<PREFIX> <DATA >
20C1001
<DATA><SUFFIX 1>
Example on how to set prefix and suffix
Prefix Setting
Step 1: scan prefix
Step 2: To set these values, scan a four-digit number (i.e. four bar codes) that
corresponds to ASCII values. See the Table 4-3 and Numeric Bar Codes
in appendix.
Step 3: i.e if you want to add “+” , scan 1043 (one by one)
01
3
4
Step 4: Set Data Transmission Format
Suffix Setting
Step 1: scan suffix
7
Keyboard Language
Interval time between scanner power on and turn off
$LAN#EN
American Keyboard
$LAN#PT
Portugal Keyboard
$LAN#FR
French Keyboard
$LAN#ES
Spanish Keyboard
$LAN#GE
Germany Keyboard
$LAN#TK
Turkey Q Keyboard
$LAN#IT
Italy Keyboard
30S 60S
90S 120S
150S 180S
8
9
Common function Barcodes
Enable/Disable UPC-E
Enable/Disable EAN-8
1000021
*Enable UPC-E 1000020
Disable UPC-E
1000041
*Enable EAN-8
1000040
Disable EAN-8
Enable/Disable EAN-13
1000031
*Enable EAN-13
1000030
Disable EAN-13
Enable/Disable Bookland EAN(ISBN)
1000231
Enable Bookland EAN
1000230
*Disable Bookland EAN
Supplementals are bar codes appended according to specific format conventions
(e.g.UPC A+2, UPC E+2, EAN 13+2, EAN 13+5). The following options are available:
• Do not read supplementals – The scan engine can only read the barcode no matter
the barcode with supplementals or not.
Decode UPC/EAN Supplementals UPC/EAN
2010E00
*Ignore UPC/EAN with Supplementals
Tabla de contenidos
Otros manuales de Lector de código de barras de Netum
Netum
Netum W9 Manual de usuario
Netum
Netum M1 Manual de usuario
Netum
Netum NT033 Manual de usuario
Netum
Netum NT-1203 Manual de usuario
Netum
Netum NT-M7 Manual de usuario
Netum
Netum RS-8000 Manual de usuario
Netum
Netum NT-1228BL Manual de usuario
Netum
Netum DataMatrix pdf417 Manual de usuario
Netum
Netum NT-1228BL Manual de usuario
Netum
Netum C200 Manual de usuario
Netum
Netum NT-1698W Manual de usuario
Netum
Netum NT-1202 Manual de usuario
Netum
Netum E800 Manual de usuario
Netum
Netum NT-M3 Manual de usuario
Netum
Netum NT-W3 Manual de usuario
Netum
Netum NT-1228BL Manual de usuario
Netum
Netum NT-1228BC Manual de usuario
Netum
Netum NT-W5 Manual de usuario
Netum
Netum NT-9600 Manual de usuario
Netum
Netum NT-1228BC Manual de usuario
