Netum NT-1200 Manual de usuario
NT-1200
Quick Setup Guide
This is a plug and play model if you use a US keyboard. If you use other type of keyboard, plug the
USB cable on your device , setup keyboard language before you use it. (refer to below Keyboard
Language Type) after that the scanner can start to work.
If you want to do other configurations please refer to below programming barcodes.
Barcode Programming
Netum barcode scanners are factory programmed for common terminal and communications
settings. If you need to change these settings, programming is accomplished by scanning the bar
codes in this guide. An asterisk (*) next to an option indicates the default setting.
Firmware Version
Read below command barcode to check scanner firmware version.
000A0
Firmware Version
Please advise the scanner model number and firmware version when you have any inquiry about
the scanner.
Keyboard Language
In order to let scanner upload the codes in a correct way, you have to set the keyboard
language.
For example
If you use French Keyboard, scan below barcode of “French keyboard” then scanner will upload
barcodes according to France keyboard layout. American Keyboard is set by default, if you use a US
keyboard you can skip this step.
American Keyboard Portugal Keyboard
French Keyboard Spanish Keyboard
Germany Keyboard Turkey Q Keyboard
Italy Keyboard
Scanning Mode
·Key Holding
Press the button to trigger the reading, release the button to end the reading. Reading
success or reading time over a single reading time will end the reading.
013300
By trigger
·Continuous Mode
Under continuous mode scanner performs continuous work. Reading success or reading
time over a single reading time will end the reading. More than the specified time will
automatically trigger the next reading
013304
Continuous Scanning
Terminator configuration
The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF
and enabling it by scanning the appropriate barcode below.
Add CR Add LF
Add CR+LF None
Reader Beep Tone
014201
014200
Beep Tone ON Beep Tone OFF
Default Configuration
If you want to cancel all the configuration that you have done to the scanner.
Scan below barcodes to the restore factory.
000B0
Factory Default
Common Function Barcodes
EAN-8
00371
00370
Enable EAN-8* Disable EAN-8
Transmit Check Digit
EAN-8 is 8 digits in length with the last one as its check digit used to verify the integrity of the
data. The default mode opens “transmit EAN-8 Check Digit”. Users can scan the code below to
choose it.
00571 00570
Transmit EAN-8 Check Digit Do Not Transmit EAN-8 Check Digit
Add-On Code
An EAN-8 barcode can be augmented with a two-digit or five-digit add-on code to form a new
one. In the examples below, the part surrounded by blue dotted line is an EAN-8 barcode while
the part circled by red dotted line is add-on code. The default mode opens “Disable Add-on
Code”. Users can take “Add-On Code Setting” for reference.
EAN-13
00361
00360
Enable EAN-13* Disable EAN-13
Transmit Check Digit
EAN-13 is 13 digits in length with the last one as its check digit used to verify the integrity of the
data. The default mode opens “Transmit EAN-13 Check Digit”. Users can choose to send it or
not.
00461 00460
Transmit EAN-13 Check Digit* Do Not Transmit EAN-13 Check Digit
Add-On Code
And EAN-8/EAN-13 Barcode can be augmented with a two-digit or five-digit add-on code
form a new one. In the example below, the part surrounded by blue line is an EAN-8
barcode while the part circled by red line is add-on code. The default mode opens “ Disable
Add-on Code”. Users can take “Add-On Code Setting” for reference.
Codabar
00851
00850
Enable Codabar Disable Codabar
Code 11
01261
01260
Enable Code 11* Disable Code 11
Code 39
00221
00220
Enable Code 39* Disable Code 39
Full ASCII
00231 00230
Enable Full ASCII* Disable Full ASCII
Code 93
00621 00620
Enable Code 93* Disable Code 93
Code128
00691 00690
Enable Code 128* Disable Code 128
GS1 DataBar Limited (RSS Limited)
01771
01770
Enable RSS Limited Disable RSS Limited*
GS1 DataBar Ominidirectional (RSS Ominidirectional)
01671
01670
Enable RSS Ominidirectional Disable RSS Ominidirectional*
UPC-A
00341
00340
Enable UPC-A * Disable UPC-A
Transmit Check Digit
UPC-A is 12 digits in length with the last one as its check digit used to verify the integrity of the
data. The default mode opens “Transmit UPC-A Check Digit”. Users can choose to send it or not.
00421
Transmit UPC-A Check Digit*
00420
Transmit UPC-A Check Digit
Add –On Code
A UPC-A barcode can be augmented with a two-digit or five-digit add-on code to form a new
one. In the examples below, the part surrounded by blue line is a UPC-A
barcode while the
part circled by red line is add-on code. Users can take “Add-On Code” Setting for reference.
\\
UPC-A Transfer to EAN-13
00391
00390
Enable UPC-A Transfer to EAN-13 Disable UPC-A Transfer to EAN-13
UPC-E
00351
00350
Enable UPC-E Disable UPC-E
Add –On Code Setting
In the example below ,the part surrounded by blue line is a UPC-A barcode while the
part circled
by red line is add-on code. Users can take “Add-On Code Setting”for reference.
Interleaved 2 of 5
00961
00960
Enable Interleaved 2 of 5 Disable Interleaved 2 of 5*
Industrial 2 of 5
01061
01060
Enable Industrial 2 of 5* Disable Industrial 2 of 5
Standard 2 of 5
01871
01870
Enable Standard 2 of 5 Disable Standard 2 of 5
Matrix 2 of 5
01461 01460
Enable Matrix 2 of 5* Disable Matrix 2 of 5
MSI
01151
01150
Enable MSI Disable MSI*
Tabla de contenidos
Otros manuales de Lector de código de barras de Netum
Netum
Netum NT-9600 Manual de usuario
Netum
Netum NT033 Manual de usuario
Netum
Netum NT-W8 Manual de usuario
Netum
Netum DataMatrix pdf417 Manual de usuario
Netum
Netum W3 Manual de usuario
Netum
Netum C Series Manual de usuario
Netum
Netum NT-M7 Manual de usuario
Netum
Netum C200 Manual de usuario
Netum
Netum NT-M3 Manual de usuario
Netum
Netum NT-1202G Manual de usuario
Netum
Netum C Series Manual de usuario
Netum
Netum NT-1228BC Manual de usuario
Netum
Netum NT-1228BL Manual de usuario
Netum
Netum NT-1202 Manual de usuario
Netum
Netum NT-1228BC Manual de usuario
Netum
Netum NT-1228BL Manual de usuario
Netum
Netum NT-1228BL Manual de usuario
Netum
Netum NT-W5 Manual de usuario
Netum
Netum NT-W3 Manual de usuario
Netum
Netum W9 Manual de usuario
