NETGEAR GS418TPP Manual

Hardware Installation Guide

Easy-Mount 16-Port Gigabit High Power

PoE+ Smart Managed Pro Switch with 2 SFP

Ports (240W)

Model GS418TPP

NETGEAR, Inc.

350 E. Plumeria DriveAugust 2019

San Jose, CA 95134, USA202-11744-03

Support

Thank you for purchasing this NETGEAR product. You can visit www.netgear.com/support

to register your product, get help, access the latest downloads and user manuals, and

join our community. We recommend that you use only official NETGEAR support

resources.

Compliance and Conformity

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

Do not use this device outdoors. If you connect cables or devices that are outdoors to

this device, see http://kb.netgear.com/000057103 for safety and warranty information.

Trademarks

Any non-NETGEAR trademarks are used for reference purposes only.

Revision History

CommentsPublish DatePublication Part Number

Removed CDAugust 2019202-11744-03

Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed Pro Switch with 2 SFP Ports (240W)

Model GS418TPP

Contents

Chapter 1 Introduction

Overview................................................................................................6

Features.................................................................................................7

Safety instructions and warnings........................................................8

Chapter 2 Hardware Overview

Hardware description........................................................................12

Front Panel..........................................................................................12

Back Panel...........................................................................................12

LEDs......................................................................................................13

Switch hardware interfaces...............................................................14

RJ-45 ports for 10/100/1000M BASE-T Ethernet connectivity..14

Reset button....................................................................................15

Factory defaults button.................................................................15

USB Port..........................................................................................15

Chapter 3 Installation

Step 1: Prepare the Site.....................................................................17

Step 2: Protect Against Electrostatic Discharge.............................18

Step 3: Unpack the Switch.................................................................19

Step 4: Install the Switch....................................................................20

Wall-Mount the Switch..................................................................20

Attach the switch to a rectangular pole or table leg.................21

Install the Switch in a Rack............................................................23

Install the switch on a flat surface.................................................24

Optional Step 5: Install SFP Transceiver Modules..........................25

Step 6: Connect Devices to the Switch............................................25

Step 7: Check the installation...........................................................26

Step 8: Apply AC Power and Check the LEDs................................26

Step 9: Manage the switch................................................................26

Chapter 4 Applications

Desktop Switching..............................................................................29

PoE Applications.................................................................................29

PoE overview..................................................................................30

Connect PoE Equipment for Surveillance and Security............30

Connect PoE Equipment in a Business Environment................31

Chapter 5 Troubleshooting

Troubleshooting Chart.......................................................................33

Additional Troubleshooting Suggestions.......................................34

Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed Pro Switch with 2 SFP Ports (240W)

Model GS418TPP

Introduction

This hardware installation guide complements the installation guide that came with your

switch and applies to the NETGEAR GS418TPP ProSAFE®16-Port Gigabit Smart Managed

Switch with PoE+ and 2 SFP Ports. The switch is specifically designed to “put your ports

where you want them” to power your IP security cameras, WiFi access points, or VoIP

phones with PoE+ (802.3at) up to 30W per port. The switch can provide a total power

budget of 240W across all active PoE+ ports.

The GS418TPP provides sixteen 1-Gigabit RJ-45 copper PoE+ ports with 2 dedicated

SFP fiber ports in a unique form factor that can be mounted on a wall, a rectangular

pole, or desktop.

This chapter serves as an introduction to the switch and includes the following sections:

• Overview

• Features

• Safety instructions and warnings

Note: For more information about the topics that are covered in this manual, visit the

support website at support.netgear.com.

Note: For technical specifications, see the data sheet at

netgear.com/business/products/switches/managed. For switch documentation, visit

downloadcenter.netgear.com.

Overview

The switch provides sixteen 10/100/1000M BASE-T RJ-45 copper ports that support

nonstop 10/100/1000M Layer 2 and Layer 3 networks. Two additional ports can accept

small form-factor pluggable (SFP) 1G fiber optical modules.

Using the 1G ports, you can create high-speed connections to a server, network attached

storage (NAS) system, or backbone network. For example, you can do the following:

•Connect switches to each other with high-speed links

•Link to high-speed servers

•Provide 10/100/1000M copper and 1G fiber connectivity

The switch provides administrative management options that let you configure, monitor,

and control the network. Using the web browser-based management interface, you can

configure the switch and the network, including the ports, the management VLAN,

VLANs for traffic control, link aggregation for increased bandwidth, quality of service

(QoS) for prioritizing traffic, and network security.

Initial discovery of the switch on the network requires the Smart Control Center program,

which runs on a Windows-based computer. If you do not use a Windows-based computer,

get the IP address of the switch from the DHCP server in the network or use an IP scanner

utility.

After discovery, you can configure the switch using the web browser-based management

interface for advanced setup and configuration of features, or the Smart Control Center

program for very basic setup. For more information, see the user manual that you can

download from downloadcenter.netgear.com.

You can install the switch freestanding or rack mounted in a wiring closet or equipment

room. The switch is IEEE compliant and offers low latency for high-speed networking.

All ports can automatically negotiate to the highest speed, which makes the switch very

suitable for a mixed environment with Fast Ethernet and Gigabit Ethernet.

Use Category 5e (Cat 5e) or higher rated Ethernet cables terminated with RJ-45

connectors to make 1-Gigibit connections.

Hardware Installation Guide6Introduction

Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed Pro Switch with 2 SFP Ports (240W)

Model GS418TPP

Features

The switch includes the following key hardware features:

•16-ports of Gigabit Ethernet with 16 PoE+ capable ports + 2 dedicated SFP Fiber

Ports.

•PoE support:

- 16 ports PoE+ (802.3at) capable

-Total PoE power budget of 240W

•MAC table size of 16K.

•Variable speed fan that can lower the noise level during low temperatures.

•Acoustic noise is equal or less than 33 dBA at 25° C.

•36 Gbps switch fabric full duplex non-blocking.

•USB port for configuration file, firmware and logs.

•Includes the following mounting hardware:

- Attachment to a wall or a pole

- Two rubber belts

- Rackmount kit

•Full compatibility with IEEE standards:

- IEEE 802.3 Ethernet

- IEEE 802.3u 100BASE-T

- IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX

- IEEE 802.3ab 1000BASE-T

- IEEE 802.1Q VLAN tagging

-IEEE 802.3x Full-duplex flow control

- IEEE 802.3ad Link Aggregation (LAG with LACP)

- IEEE 802.1AB LLDP

-IEEE 802.1p Class of Service (QoS)

- IEEE 802.1D Spanning Tree Protocol (STP)

- IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)

- IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)

Hardware Installation Guide7Introduction

Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed Pro Switch with 2 SFP Ports (240W)

Model GS418TPP

- IEEE 802.1x RADIUS Network Access Control

-IEEE 802.3az Energy Efficient Ethernet (EEE)

•AutoSensing and autonegotiating capabilities for all ports.

•Auto Uplink™ technology is supported on all ports.

•Automatic address learning function to build the packet-forwarding information

table. The table contains up to 16K Media Access Control (MAC) addresses.

•Store-and-forward transmission to remove bad packets from the network.

•Full-duplex IEEE 802.3x pause frame flow control.

•Active flow control to minimize packet loss and frame drops.

•Half-duplex backpressure control.

•Per-port status LEDs and system status LEDs.

•NETGEAR green power-saving features:

-Energy efficiency mode that fully conforms to the IEEE802.3az standard

- Per-port automatic change to a lower power mode when the port link is down

Safety instructions and warnings

Use the following safety guidelines to ensure your own personal safety and to help

protect your system from potential damage.

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,

observe the following precautions:

•This product is designed for indoor use only in a temperature-controlled and

humidity-controlled environment. For more information, see the environmental

specifications in the appendix or the data sheet.

Any device that is located outdoors and connected to this product must be properly

grounded and surge protected.

Failure to follow these guidelines can result in damage to your NETGEAR product,

which might not be covered by NETGEAR’s warranty, to the extent permissible by

applicable law.

Hardware Installation Guide8Introduction

Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed Pro Switch with 2 SFP Ports (240W)

Model GS418TPP

•Observe and follow service markings:

- Do not service any product except as explained in your system documentation.

Some devices should never be opened.

-If applicable to your device, opening or removing covers that are marked with

the triangular symbol with a lightning bolt can expose you to electrical shock.

We recommend that only a trained technician services components inside these

compartments.

•If any of the following conditions occur, unplug the product from the electrical outlet

and replace the part or contact your trained service provider:

- Depending on your device, the power adapter, power adapter cable, power

cable, extension cable, or plug is damaged.

-An object fell into the product.

- The product was exposed to water.

- The product was dropped or damaged.

-The product does not operate correctly when you follow the operating

instructions.

•Keep your system away from radiators and heat sources. Also, do not block cooling

vents.

•Do not spill food or liquids on your system components, and never operate the

product in a wet environment. If the system gets wet, see the appropriate section in

your troubleshooting guide, or contact your trained service provider.

•Do not push any objects into the openings of your system. Doing so can cause fire

or electric shock by shorting out interior components.

•Use the product only with approved equipment.

•If applicable to your device, allow the product to cool before removing covers or

touching internal components.

•Operate the product only from the type of external power source indicated on the

electrical ratings label. If you are not sure of the type of power source required,

consult your service provider or local power company.

•To avoid damaging your system, if your device uses a power supply with a voltage

selector, be sure that the selector is set to match the power at your location:

-115V, 60 Hz in most of North and South America and some Far Eastern countries

such as South Korea and Taiwan

- 100V, 50 Hz in eastern Japan and 100V, 60 Hz in western Japan

-230V, 50 Hz in most of Europe, the Middle East, and the Far East

Hardware Installation Guide9Introduction

Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed Pro Switch with 2 SFP Ports (240W)

Model GS418TPP

•Be sure that attached devices are electrically rated to operate with the power available

in your location.

•Depending on your device, use only a supplied power adapter or approved power

cable:

If your device uses a power adapter:

-If you were not provided with a power adapter, contact your local NETGEAR

reseller.

-The power adapter must be rated for the product and for the voltage and current

marked on the product electrical ratings label.

If your device uses a power cable:

-If you were not provided with a power cable for your system or for any

AC-powered option intended for your system, purchase a power cable approved

for your country.

-The power cable must be rated for the product and for the voltage and current

marked on the product electrical ratings label. The voltage and current rating of

the cable must be greater than the ratings marked on the product.

•To help prevent electric shock, plug the system and peripheral power cables into

properly grounded electrical outlets.

•If applicable to your device, the peripheral power cables are equipped with

three-prong plugs to help ensure proper grounding. Do not use adapter plugs or

remove the grounding prong from a cable. If you must use an extension cable, use

a three-wire cable with properly grounded plugs.

•Observe extension cable and power strip ratings. Make sure that the total ampere

rating of all products plugged into the extension cable or power strip does not

exceed 80 percent of the ampere ratings limit for the extension cable or power strip.

•To help protect your system from sudden, transient increases and decreases in

electrical power, use a surge suppressor, line conditioner, or uninterruptible power

supply (UPS).

•Position system cables, power adapter cables, or power cables carefully. Route

cables so that they cannot be stepped on or tripped over. Be sure that nothing rests

on any cables.

•Do not modify power adapters, power adapter cables, power cables or plugs. Consult

a licensed electrician or your power company for site modifications.

•Always follow your local and national wiring rules.

Hardware Installation Guide10Introduction

Easy-Mount 16-Port Gigabit High Power PoE+ Smart Managed Pro Switch with 2 SFP Ports (240W)

Model GS418TPP

Otros manuales para GS418TPP

Tabla de contenidos

Otros manuales de Cambiar de NETGEAR

NETGEAR

NETGEAR ProSafe GS516TP Manual de usuario

NETGEAR

NETGEAR GS752TPv2 Manual de usuario

NETGEAR

NETGEAR ProSafe FS728TPv2 Manual de usuario

NETGEAR

NETGEAR ProSafe GS105v3 Manual de usuario

NETGEAR

NETGEAR GS316 Manual de usuario

NETGEAR

NETGEAR GSM7328S - ProSafe Switch - Stackable Manual de usuario

NETGEAR

NETGEAR GS750E Manual de usuario

NETGEAR

NETGEAR FSM7328S - ProSafe Switch Manual de usuario

NETGEAR

NETGEAR ProSafe GS700TP Manual de instrucciones

NETGEAR

NETGEAR Smart Switch GS752TXS Manual

NETGEAR

NETGEAR GS105v5 Manual de usuario

NETGEAR

NETGEAR ProSafe GS116 Manual de usuario

NETGEAR

NETGEAR ProSafe JGSM7224 Manual

NETGEAR

NETGEAR AV Series Manual de usuario

NETGEAR

NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart... Manual de usuario

NETGEAR

NETGEAR XS712Tv2 Manual de usuario

NETGEAR

NETGEAR GS748T - ProSafe Smart Switch Manual de usuario

NETGEAR

NETGEAR GSS108E Manual de usuario

NETGEAR

NETGEAR GS724TS - ProSafe 24 Port Gigabit Stackable Smart... Manual de usuario

NETGEAR

NETGEAR GS716T - ProSafe Switch Manual de instrucciones

NETGEAR

NETGEAR DS 508 Manual de usuario

NETGEAR

NETGEAR 700 Series Guía de seguridad

NETGEAR

NETGEAR GS748Tv4 Manual

NETGEAR

NETGEAR GS752TPv2 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario