NETGEAR R9000 Manual de usuario
Contents
1 Introduction• 2 Hardware Specifications• 3 Installation• 4 Upgrading/Downgrading
DD-WRT
•
5 Recovery• 6 GPIO• 7 VLAN Detached networks
7.1 Detaching the
SFP+ port
♦
•
Introduction
Hardware Specifications
See Netgear R9000 on wikidevi
This router can handle top VPN speeds, as of 2019.
Please note, Wireless-AD (60GHz) support is untested at this time, 2019.
10g interface- supported SFP hardware info:
https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1230130#1230130
Installation
Download and flash the factory-to-ddwrt.img file:
Authenticate to the router. The original Netgear firmware defaults to IP address 192.168.1.1,
username "admin" and password "password"
1.
Go to the Administration page - then Upgrade (or something similar).2. You will see a notice about the file you uploaded being older than the firmware currently on the
router. Click Yes to proceed.
3.
The router will flash DD-WRT. Wait a few minutes (5 min to be safe).4.
Try logging into DD-WRT at http://192.168.1.1. You should see a screen asking you to create a username and
password.
Netgear_R9000
Contents 1
Upgrading/Downgrading DD-WRT
Download and flash the r9000-webupgrade.bin file:
NOTE: The webupgrade.bin file is only used to upgrade or downgrade to a *different* version
of DD-WRT.
•
Authenticate to the router.1. Go to the Administration -> Firmware Upgrade page.2. Select the r9000-webupgrade.bin file you downloaded (do not select "reset to defaults after flashing").3. Click on "Upgrade".4. Wait a minimum of 5 minutes for router to flash and reboot.5.
NOTE: reset is only necessary if you run into issues or changes in firmware require it. There are two
methods of doing this:
via the "Administration -> Factory Defaults" page or via telnet/ssh nvram erase && reboot.
•
Recovery
The same rules apply for dd-wrt tftp as you would for stock below. Just make sure you grab the
factory-to-dd-wrt.IMG file.
ONLY IMG files can be TFTP'd onto the router.
Make sure you statically set the IP address on your computer to 192.168.1.2; subnet 255.255.255.0 and
gateway to 192.168.1.1.
If you want to go back to stock: All you need to do is TFTP the stock firmware back onto the router. Make
sure to factory reset dd-wrt on the admin>factory defaults tab. Grab the latest Firmware file from Netgear:
https://www.netgear.com/support/product/R9000.aspx#download
1. Get TFTP64 installed on your PC https://www.tftpd64.com/ (MAKE SURE TO ALLOW THIS
PROGRAM IN YOUR FIREWALL FOR BOTH PUBLIC AND PRIVATE NETWORKS OR YOU'LL
NEVER SEND THE IMG FILE)
2.Read how to use "TFTP client mode"-
https://kb.netgear.com/000059633/How-to-upload-firmware-to-a-NETGEAR-router-using-TFTP-client
3.Get the TFTP program up and running and ready to push the correct file onto the router- then you will wait
for step 6 below.
To put the R9000 into TFTP mode.
1. Power off the router.
2.Hold down the reset button.
Netgear_R9000
Upgrading/Downgrading DD-WRT 2
3.Power on the router and keep holding down the reset button.
4.When the router first boots the power led flashes orange and then it will switch to a slow white flash. Keep
holding down reset button. The slow white flash will change to a faster white flash and then to a second even
faster white flash. Let it blink 3-4 on the second set of faster white flashes and let go of the reset button and
now send the IMG file via TFTP. When the power LED is fast white blinking, the router is in TFTP mode and
ready to accept any IMG file (Stock or dd-wrt). You will have about 2-3 minutes to send the IMG file.
5. Go to the tftp program and re-select your NIC with the static IP 192.168.1.2 from the dropdown. It will
change as you boot the router initially so you have to go back and select the right NIC/IP in the TFTP
program. (You can avoid this by using a cheap/dumb 1gig switch which keeps your NIC active the whole time
and shouldn't have to worry about re-selecting the right NIC in the dropdown)
6. Push the file onto the router using TFTP64.
7.Wait a full 5 minutes before touching the router. It should do it's update and reboot by itself. Keep your
browser open and try to load 192.168.1.1 It should load the stock firmware gui/website automatically once the
router is booted. If the stock gui loads, clear your static NIC settings to grab IP's automatically again.
8. If 5 minutes have passed and nothing has happened performing website refreshes, then reboot the router
manually and try loading the gui website again.
GPIO
GPIO LED's
22 =Power LED
23 =WAN LED
36 =USB 1 LED
37 =USB 2 LED
30 =10Gbps LED
29 =WIFI Button LED
https:/http://wiki.dd-wrt.com/wiki.dd-wrt.comhttp://wiki.dd-wrt.com/wiki/index.php/LED_Scripts
VLAN Detached networks
Putting any of the 6 ethernet ports on a separate detached VLAN network is complicated by the fact that there
are two internal hardware switches used by R9000 for routing traffic. Creating additional Vlan's on the
R9000, right now, has not yet been "figured out" for the 6 ehternet ports.
However, the SFP+ port can be easily segregated into its own VLAN since it's the only port associated with
the eth0 interface. Read below for how to unbridge eth0, which is bridged to br0 by default .
Netgear_R9000
Recovery 3
Detaching the SFP+ port
To create a 10 gb/sec VLAN, start by setting up the SFP+ port as you would any VAP by navigating to Setup
>Networking:
Next, under the Port Setup heading, locate the group box called Network Configuration eth0 and unbridge
the interface by selecting the Unbridged radio button assigned to Bridge Assignment. Since it's going to be a
VLAN, select the Net Isolation radio button to isolate it from the rest of your network and assign IP/Subnet
mask of your choosing.
Netgear_R9000
Detaching the SFP+ port 4
Optionally, you can force DNS redirection if you want the devices on that VLAN to be forced into using a
preferred DNS server choice by enabling the Forced DNS Redirection option and entering the DNS server IP
in the Optional DNS Target text boxes.
Stop here and click Save and Apply Settings at the bottom of the page, in that order.
Finally, create a DHCP server for your newly minted VLAN by scrolling to the bottom of the same page and,
under the DHCPD heading, click the Add button to create a new DHCP server. In the ensuing list box, scroll
through the list of interfaces and select eth0, make sure it is enabled by selecting On in the neighboring list
box, leave the default lease time or modify it, click Save, then Apply Settings, in that order.
Netgear_R9000
Detaching the SFP+ port 5
Restart for good measure and begin using the SFP+ VLAN.
As for choice of SFP+ modules, note that there really isn't any meaningful speed difference between them as
shown in this Serve The Home YT video: https://www.youtube.com/watch?v=4qM9dyEuaS4
Also note that the SFP+ modules do get hot. I would change the fan threshold parameters to make sure that
your R9000 fans stay on 24/7. They aren't loud and could help keep mobo and CPU speeds in check during
the incoming summer months while transferring files at 10 gb/sec in your new VLAN.
Netgear_R9000
Detaching the SFP+ port 6
Otros manuales para R9000
1
Tabla de contenidos
Otros manuales de Enrutador de red de NETGEAR
NETGEAR
NETGEAR RP614 - Web Safe Router Manual de usuario
NETGEAR
NETGEAR Nighthawk X6 R7900 Manual de usuario
NETGEAR
NETGEAR Orbi RBS50Y Manual de usuario
NETGEAR
NETGEAR MVBR1210C Manual de usuario
NETGEAR
NETGEAR N300 Hoja de información del producto
NETGEAR
NETGEAR PR2000 Manual de usuario
NETGEAR
NETGEAR Nighthawk AX6 Manual de usuario
NETGEAR
NETGEAR Orbi Manual de usuario
NETGEAR
NETGEAR ProSAFE GS108PEv3 Manual de usuario
NETGEAR
NETGEAR Insight WAC540 Instrucciones de instalación
NETGEAR
NETGEAR GS908 Manual de usuario
NETGEAR
NETGEAR DGN2200 - Wireless-N 300 Router Manual de usuario
NETGEAR
NETGEAR RP114 Manual de usuario
NETGEAR
NETGEAR D6400 Manual de usuario
NETGEAR
NETGEAR R7300DST Manual de usuario
NETGEAR
NETGEAR WGR614v2 Manual de usuario
NETGEAR
NETGEAR GSS108E Manual
NETGEAR
NETGEAR Nighthawk AX4 Manual de usuario
NETGEAR
NETGEAR RT328 Manual de usuario
NETGEAR
NETGEAR Orbi Pro SXS80 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad
LevelOne
LevelOne FBR-1416 Manual de usuario