NETGEAR PR2000 Manual de usuario
Quick Start
NETGEAR Trek
N300 Travel Router and Range Extender
Model PR2000
WiFi
USB
USB
LAN
Internet/LAN
Reset
NETGEAR
Power
Internet
2
Getting Started
Thank you for purchasing the NETGEAR Trek N300 Travel Router and
Range Extender PR2000. You can connect your Trek to the Internet by
using the Trek in hotspot mode, extender mode, or router mode.
Note: You can also use the Trek in bridge mode or AP mode. For more
information, see the user manual. You can get the user manual online at
http://downloadcenter.netgear.com or through a link in the Trek’s user
interface. For more information about how to access the Trek’s user
interface, see View or Change the Trek’s Settings on page 17.
Hotspot mode Extender mode
Router mode
NETGEAR
Power
Internet
WiFi
USB
Wired
Power Off
Wireles
NETGEAR
Power
Internet
WiFi
USB
Wired
Power Off
Wireles
NETGEAR
Power
Internet
WiFi
USB
Wired
PowerOff
Wireles
3
Meet Your NETGEAR Trek
Before you install your Trek, familiarize yourself with its LEDs, buttons, and
port.
Internet Mode Switch
Put the Internet Mode switch in one of the following positions:
• Wired. Set the switch to Wired if you want to connect the Trek to the
Internet with an Ethernet cable. For example, set the switch to Wired
if you want to use the Trek in router mode or AP mode.
• Power o. Set the switch to Power o to turn o the Trek. Make
sure the switch is set to Power o before plugging the Trek into an
electrical outlet.
• Wireless. Set the switch to Wireless to connect the Trek to the
Internet with a WiFi connection. For example, set the switch to
Wireless if you want to use the Trek in hotspot mode, extender mode,
or bridge mode.
4
Connection Ports and Reset Button
The Trek has the following connection ports and reset button:
• Reset button. To reset the Trek to its factory default settings, insert
a paper clip into the Reset hole and hold it until the Internet LED
blinks.
• Internet/LAN port. When the Internet Mode switch is set to
Wired, this port becomes an Internet port. When the switch is set to
Wireless, this port becomes a LAN port.
• LAN port. A LAN port for any Ethernet-enabled device.
• USB port. A USB port for USB storage or USB printer. If the Trek is
plugged into an AC wall outlet, the USB port can also be used as a
charger.
Reset button USB port
Internet/LAN port LAN port
5
Indicator LEDs
Monitor the status of your Trek using the following LEDs:
Power LED • Green. The Trek is powered on.
• O. The Trek is powered o.
Internet LED • Green. The Trek is connected to the Internet.
• Blinking green. One of the following occurred:
• The Reset button was pressed longer than five
seconds.
• A firmware upgrade is in progress.
• The bandwidth limit was exceeded.
• O. The Trek is not connected to the Internet.
WiFi LED • Green. The WiFi radio is operating.
• O. The WiFi radio is o.
USB LED • Green. A USB device is connected and ready.
• O. No USB device is connected.
6
Set Up Your Trek
¾To set up your Trek:
1. Record your Trek’s WiFi network name (SSID) and WiFi password.
The SSID and WiFi password are on the sticker near the Internet
mode switch. You can write the WiFi settings from the sticker in this
space for easy reference.
SSID:
WiFi password:
2. Connect the Trek to a power source.
Use one of these options:
• AC power connection. Plug the Trek into an AC wall outlet.
• Micro USB connection. Connect a micro USB cable to the Trek
and to a USB port on another device.
NETGEAR
Power
Internet
WiFi
USB
Wired
Power Off
Wireles
NETGEAR
Internet
via
Wired
Power Off
Wireles
AC power connection Micro USB connection
7
3. Rotate the Trek’s cover clockwise to orient the antenna.
The WiFi antenna is inside the cover. For best performance, keep the
cover vertical when you use your Trek.
NETGEAR
Internet
via
Wired
Power Off
Wireles
Power
Internet
WiFi
USB
WiFi
USB
USB
LAN
Internet/LAN
Reset
NETGEAR
Power
Internet
NETGEAR
LAN
Internet/LAN
Reset
USB
WiFi
USB
Power
Internet
4. Connect your Trek to the Internet.
Use one of these options:
• Use the Trek in Hotspot Mode on page 8
• Use the Trek in Extender Mode on page 11
• Use the Trek in Router Mode on page 14
8
Use the Trek in Hotspot Mode
Use the Trek in hotspot mode to connect to a public hotspot. The Trek’s
firewall protects your devices from known DoS attacks and port scans
from the Internet.
CAUTION: Most public WiFi hotspots oer no security. NETGEAR
recommends that you do not send personal information over the Internet
when using a public WiFi hotspot.
NETGEAR
Power
Internet
WiFi
USB
Wired
Power Off
Wireles
¾To use the Trek in hotspot mode:
1. Connect your Trek to a power source and rotate the antenna.
For more information, see Set Up Your Trek on page 6
2. Set the Internet Mode switch to Wireless.
3. Connect your computer or WiFi device to the Trek.
Trek
9
You can use an Ethernet cable or connect with WiFi:
• For a wired connection, use an Ethernet cable (not included) to
connect your computer to the LAN port on the Trek.
• To connect with WiFi, use the Trek’s network name (SSID) and
WiFi password, which are on the sticker near the Internet Mode
switch. For more information, see Connect Devices to Your Trek
with WiFi on page 16.
4. Launch a web browser.
5. Enter www.routerlogin.net in the address field of the browser.
The Wireless as WAN screen displays, which shows the available WiFi
networks.
6. If a login screen displays, do the following:
a. Enter admin for your user name and password for your
password.
The BASIC Home screen displays.
b. Select Internet.
The Wireless as WAN screen displays, which shows the available
WiFi networks.
10
7. Clear the Extend my current wireless router’s range check box.
8. Select a radio button next to the WiFi network to which you want to
connect.
9. From the Security list, select the WiFi network’s security option.
10. In the Password (Network Key) field, type the WiFi network’s
password.
11. For the Internet IP Address setting, select one of the following radio
buttons:
• Get Dynamically. The Internet service provider (ISP) uses DHCP
to assign your IP address. Your ISP automatically assigns these
addresses.
• Use Static IP Address. Enter the IP address, IP subnet mask, and
the gateway IP address that your ISP assigned. The gateway is
the ISP’s gateway to which your Trek connects.
12. To be able to use these settings again without having to reenter them,
select the To save a name for profile check box and in the field
provided, type a name for the profile.
Create a descriptive name for the profile to help you remember the
settings. For example, if you visit a hotel frequently, you might use the
hotel name as the profile name.
13. Click the Apply button.
It might take up to two minutes before the Trek connects to the WiFi
network.
Otros manuales para PR2000
4
Tabla de contenidos
Otros manuales de Enrutador de red de NETGEAR
NETGEAR
NETGEAR GC110 Manual de usuario
NETGEAR
NETGEAR RO318 Manual de usuario
NETGEAR
NETGEAR R6700AX Manual de usuario
NETGEAR
NETGEAR Orbi Pro WiFi 6 Mini router Manual de usuario
NETGEAR
NETGEAR ProSAFE FS728TLP Manual
NETGEAR
NETGEAR RH340 - ISDN INET Gateway Router Manual de usuario
NETGEAR
NETGEAR RT338 Manual de usuario
NETGEAR
NETGEAR orbi RBK652S Manual de usuario
NETGEAR
NETGEAR GS408EPP Manual
NETGEAR
NETGEAR FSM7328SNA Manual de instrucciones
NETGEAR
NETGEAR DGFV338 - ProSafe Wireless ADSL Modem VPN Firewall... Guía rápida
NETGEAR
NETGEAR Orbi RBK20 Manual de usuario
NETGEAR
NETGEAR C6300v2 Manual de usuario
NETGEAR
NETGEAR RAX15 Manual de usuario
NETGEAR
NETGEAR RBK762S Manual de usuario
NETGEAR
NETGEAR Wireless-N 150 Manual de usuario
NETGEAR
NETGEAR Orbi RBR50 Manual del operador
NETGEAR
NETGEAR SRK60B04 Manual de usuario
NETGEAR
NETGEAR JNR3210 Manual de usuario
NETGEAR
NETGEAR C6250 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad
LevelOne
LevelOne FBR-1416 Manual de usuario