Neilsen CT4448 Instrucciones de operación

DENT TOOL KIT CT4448

ORIGINAL INSTRUCTION

Read the operating manual thoroughly before work and keep it

for future reference.

Cannon Tools Limited

Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

INCLUDES:

1pc glue gun(220-240V~, 50Hz, 40W)

1pc sliding hammer to pull out hard dents

1pc dent lifter (Baby face mini lifter or normal mini lifter) for slight dents on flat surface

1pc glue remover

1pc scraper for gentle removal of dent pads

8pcs black glue sticks (11 x 200mm) with very good performance for best results

19pcs glue tabs in various sizes and shapes

OPERATION AND USE OF ARTICLE

Step1:

The first position in the vehicle collision / dent. Clean the surface of the process. Use only mild

cleaning agents.The use of surface coarse sponge, will cause irreparable damage.

Step2:

Use the glue gun, push the glue stick into the back of the glue gun . Heating the glue gun and

the glue stick melt.

Step3:

Use hot glue gun, put glue on the glue tab, and then place the recess in the dent glue tab.

Step4:

use the T bar slide hammer or dent mini lifter extraction of the bump.what tool you use, also

depends on the size of the dent, up to 30mm diameter is the dent mini lifter,Other use the slide

hammer.

Step5:

When the temperature reaches the right time, do not be too hard. Then pull until the glue tab is

removed.

Step6:

Use the release agent , dissolve glue. Use of the scraper, remove the glue.

Step7:

Finally, use a soft clean cloth wipe again residual glue, make the body to restore new look.

ELECTRICAL INFORMATION

Warning

Mains plug replacement (UK & Ireland only)

If you need to replace the fitted plug of the tool, then follow the instructions below.

Machines that are connected direct to mains supply.

For machines that are double insulated, do not require a connection to earth.

If in doubt consult a qualified electrician

The wires are coloured as follows

Blue Neutral (N)

Brown Live (L)

3amp BS 1363A Fuse

Always secure the wires in the plug terminals carefully make sure no loose strands are left

exposed as they can short circuit and cause injury, fire and or damaged the tool.

Secure the cable in the cord grip firmly.

Never use a light socket. Never connect the live (L) or neutral (N) wires to the earth pin marked

(E).

NOTE: If your mains wires differ from the above consult a qualified electrician. Always make

sure the mains supply is of correct voltage and you use the correct fuse protection.

Regularly inspect all machines electrical connection and wiring condition for damage. Any

faults detected should be immediately rectified before further use of the machine. Always have

the wiring checked by a qualified electrician.

In use ensure all wiring and extension cords are kept clear of any cutting tools, sharp objects

and any other workshop hazards such as wet floors, chemicals, solvents etc.

This machine is protected by a 3 amp fuse make sure the correct fuse is used.

To prevent fire or shock hazards do not expose these products to rain or moisture.

CANNON TOOLS LTD

Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.

Made in China

Tabla de contenidos

Otros manuales de Herramientas de Neilsen

Neilsen

Neilsen CT0933 Manual de usuario

Neilsen

Neilsen CT0729 Instrucciones de operación

Neilsen

Neilsen CT2737 Manual de usuario

Neilsen

Neilsen CT5202 Manual de usuario

Neilsen

Neilsen OPEL VAUXHALL CT2909 Manual de usuario

Neilsen

Neilsen CT4342 Manual de usuario

Neilsen

Neilsen CT4790 Manual de usuario

Neilsen

Neilsen CT2102 Manual de usuario

Neilsen

Neilsen CT4694 Manual de usuario

Neilsen

Neilsen CT0527 Manual de usuario

Neilsen

Neilsen CT5271 Manual de usuario

Neilsen

Neilsen CT1057 Manual de usuario

Neilsen

Neilsen CT2266 Manual de usuario

Neilsen

Neilsen NAH-A30B Manual de usuario

Neilsen

Neilsen CT1535 Manual de usuario

Neilsen

Neilsen CT3583 Manual de usuario

Neilsen

Neilsen CT4793 Manual de usuario

Neilsen

Neilsen CT1056 Manual de usuario

Neilsen

Neilsen CT2247 Manual de usuario

Neilsen

Neilsen CT1509 Manual de usuario

Neilsen

Neilsen CT4852 Manual de usuario

Neilsen

Neilsen CT3073 Manual de usuario

Neilsen

Neilsen CT4794 Manual de usuario

Neilsen

Neilsen CT4621 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar