Neilsen CT1535 Manual de usuario

AUTO RETRACTABLE AIR HOSE REEL 1/2” x 50FT

CT1535

Ref no. ZYM07-1-20

ORIGINAL INSTRUCTIONS

Cannon Tools Limited

Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

SAVE THESE INSTRUCTIONS AND PRECAUTIONS.

READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.

EC DECLARATION OF CONFORMITY

We CANNON TOOLS LTD

20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.

Declare that the following machine complies with the appropriate basic safety

and health requirements of the EC Directive based on its design and type, as

brought into circulation by us.

In case of alteration of the machine, not agreed upon by us, this declaration

will lose its validity.

Product description:

AUTO RETRACTABLE AIR HOSE REEL

Model: CT1535 (Ref no.ZYM07-1-20)

Applicable EC Directives:

EC Machinery Directive 2006/42/EC

Harmonized standards

EN ISO 12100:2010

20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

Mr. Gurcharan Tony Singh Sanghera

Managing Director

CANNON TOOLS LTD

2020-11-13

TOOL USE AND CARE

1.Do not force the tool. Use the correct tool for the application. The correct tool will

do the job better and safer at the rate for which the tool is designed.

2.Disconnect the tool from the air source before making any adjustments,changing

accessories, or storing the tool. Such preventive safety measures reduce the risk

of starting the tool unintentionally.

3. Store the tool when it is idle out of reach of children and other untrained

persons. A tool is dangerous in the hands of untrained users.

4.Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that affects the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

There is a risk of bursting if the tool is damaged.

5. Use only accessories that are identified by the manufacturer for the specific tool

model. Use of an accessory not intended for use with the specific tool model,

increases the risk of injury to persons.

SERVICE

1.Tool service must be performed only by qualified repair personnel.

2.When servicing a tool, use only identical replacement parts. Use only

authorized parts.

3.Use only the lubricants supplied with the tool or specified by the manufacturer.

AIR SOURCE

WARNING

●Never connect to an air source that is capable of exceeding 250 psi. Over

pressurizing the tool may cause bursting, abnormal operation, breakage of the

tool or serious injury to persons. Use only clean, dry, regulated compressed air at

the rated pressure or within the rated pressure range as marked on the tool.

Always verify prior to using the tool that the air source has been adjusted to the

rated air pressure or within the rated air-pressure range.

●Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an

air source for the tool. Such gases are capable of explosion and serious injury to

persons.

SPECIFICATIONS

MODEL HOSE

LENGTH

WORKING

PRESSURE AIR HOSE SIZE

CT1535 50FEET 300psi 1/2”

COMPONENTS AND CONTROLS

1. Set-Up

REPOSITIONING BRACKET

1.Remove the Bolts on the Support Post and reposition to move the guide rollers,

if needed, for the desired mounting location (wall, floor or ceiling).

2.Replace the Bolts and tighten.

MOUNTING REEL

1.Choose a mounting location that is free of electrical wiring or other obstructions,

and is sturdy enough to support the weight of the Reel and hose as well as the

force used to extend and retract it.

2.Make a paper template from the mounting plate of the Reel. Mark the center of

the bolt holes in the desired mounting location.

3.Check for hidden wiring, then, drill holes to accommodate 1/2” bolts (not

included).

4.Mount the Reel and secure in place with four bolts.

2. Operation

ADJUST THE SPRING TENSION

1.Pull out approximately six feet of Hose.

2.Remove the Hose Stopper from the Hose and slide the Hose out of the Roller

Guide so the Hose is hanging loose.

a. To increase tension, wrap the loose hose one time around the Reel Drum.

b. To decrease tension, unwrap the hose one time from the drum.

3.Run the hose back through the guide and re-attach the hose stopper.

4.Pull the Hose out several feet to check the tension.

GENERAL OPERATING INSTRUCTIONS

1.Check the Wheel operation by slowly pulling the Hose out. You should hear a

clicking noise.

2.To lock the Hose, pull it out a minimum of 1/2 revolution and it will stay locked

after the first, second, or third click.

3.To unlock, slowly pull until the clicking stops, and let it retract until the Hose

Stopper hits the Hose Guide.

4.Attach a coupler (sold separately) to your air compressor hose and apply

thread seal tape to the Inlet fitting on the Reel. Connect the coupler to the Inlet

fitting.

5.Connect your air tool to the other end of the Hose using another coupler and

thread seal tape.

6.Follow all instructions from the air tool and compressor for set up and use.

7.When finished using the Hose, disconnect the air tool and retract the hose.

Wipe the Hose Reel clean with a dry cloth.

MAINTENANCE

CLEANING, MAINTENANCE, AND LUBRICATION

1. BEFORE EACH USE, inspect the general condition of the tool. Check for:

• loose hardware or housing,

• misalignment or binding of moving parts,

• cracked or broken parts, and any other condition that may affect its safe

CAUTION

•Hold on to the Hose while it is rewinding, to avoid damage to the Hose Reel.

WARNING

• To prevent serious injury：

Detach air supply from this product before performing any inspection,

maintenance, or cleaning procedures.

• To prevent serious injury from tool failure:

Do not use damaged equipment. If abnormal noise, vibration, or leaking air

occurs, have the problem corrected before further use.

NOTICE

• These procedures are in addition to the regular checks and maintenance

explained as part of the regular operation of the Hose Reel.

operation.

2.AFTER EACH USE, re-wind the hose onto the reel and wipe the Hose Reel

clean with a dry cloth.

HOSE REPLACEMENT

1.Remove the Hose Stopper from the hose and set aside.

2.Pull out the old Hose and securely lock the Hose Reel.

3.Disconnect the old hose from the swivel joint and remove the hose.

4.Run the new hose through the Guide Roller and through the opening in the

drum flange.

5.Use thread seal tape on the hose fitting threads and screw the fitting onto the

swivel and tighten.

6.Attach the Hose Stopper on the end of the Hose near the Outlet fitting.

7.Carefully release the Drum Latch and allow the Hose to wind onto the reel,

evenly

distributing the Hose across the Reel.

WARNING

• Internal spring is not user serviceable or user-replaceable.

CANNON TOOLS LTD

Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.

Made in China

Tabla de contenidos

Otros manuales de Herramientas de Neilsen

Neilsen

Neilsen CT1509 Manual de usuario

Neilsen

Neilsen CT1056 Manual de usuario

Neilsen

Neilsen CT5271 Manual de usuario

Neilsen

Neilsen CT4188 Manual de usuario

Neilsen

Neilsen CT5823 Manual de usuario

Neilsen

Neilsen CT5202 Manual de usuario

Neilsen

Neilsen CT1057 Manual de usuario

Neilsen

Neilsen CT2247 Manual de usuario

Neilsen

Neilsen CT0729 Instrucciones de operación

Neilsen

Neilsen CT4793 Manual de usuario

Neilsen

Neilsen CT2102 Manual de usuario

Neilsen

Neilsen CT4794 Manual de usuario

Neilsen

Neilsen CT0933 Manual de usuario

Neilsen

Neilsen VAG CT5467 Manual de usuario

Neilsen

Neilsen CT2737 Manual de usuario

Neilsen

Neilsen NAH-A30B Manual de usuario

Neilsen

Neilsen CT0676 Manual de usuario

Neilsen

Neilsen CT1533 Manual de usuario

Neilsen

Neilsen CT4342 Manual de usuario

Neilsen

Neilsen CT4694 Manual de usuario

Neilsen

Neilsen CT4448 Instrucciones de operación

Neilsen

Neilsen CT4852 Manual de usuario

Neilsen

Neilsen OPEL VAUXHALL CT2909 Manual de usuario

Neilsen

Neilsen CT0527 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar