NEC Univerge SV9300 Manual de usuario

Migration Manual

NWA-088658-001

Issue 1.0

LIABILITY DISCLAIMER

NEC Corporation reserves the right to change the specifications,

functions, or features, at any time, without notice.

NEC Corporation has prepared this document for use by its employees

and customers. The information contained herein is the property

of NEC Corporation and shall not be reproduced without prior written

approval from NEC Corporation.

Dterm is registered trademarks of NEC Corporation.

PCPro is a trademark of NEC Corporation.

NEC Corporation

Additional Information

This page describes the additional information of this manual.

[Regarding the use of VoIPDB blade]

The VoIPDB blade that can be used for SV9300 is as follows.

X:Available -:Not available

VoIPDB blade UNIVERGE SV8300 UNIVERGE SV9300

PZ-64IPLA/PZ-128IPLA X -

PZ-64IPLC-A/PZ-128IPLC-A X X

(For migration)

GPZ-64IPLC-A/GPZ-128IPLC-A X

(For adding blade)

(For migration)

GPZ-64IPLD/GPZ-128IPLD - X

NOTE:

When using GPZ-64IPLD/ GPZ-128IPLD (VoIPDB) in the SV9300, the automatic update of

SV9300 VoIPDB Firmware is performed only at the first start-up. Incoming/outgoing call via

VoIPDB is not allowed for about 10 minutes from system start-up until firmware update

completion. When using the VoIPDB except for GPZ-64IPLD/ GPZ-128IPLD, manual update

by PCPro is available.

THIS PAGE LEFT BLANK INTENTIONALLY.

INTRODUCTION

SV9300 provides a procedure to migrate from an existing SV8300 to SV9300 system.

This manual describes required equipment, conditions, precautions and procedure for the migration.

* This migration procedure is only available on an existing SV8300.

This manual consists of the following chapters.

CHAPTER 1 OUTLINE

This chapter explains the required equipment for migration and also provides conditions and

precautions for system migration.

CHAPTER 2 MIGRATION PROCEDURE

This chapter explains detailed procedure to migrate from an existing SV8300 to SV9300 system.

- i -

UNIVERGE SV9300

MIGRATION MANUAL

TABLE OF CONTENTS

INTRODUCTION ........................................................................................................................................... i

CHAPTER 1 OUTLINE..................................................................................................................................... 1

Function Overview........................................................................................................................................ 1

Required Equipment..................................................................................................................................... 2

Migration Conditions..................................................................................................................................... 3

Conditions for Migration from SV8300 to SV9300 System....................................................................... 3

Conditions for Migration of Voice Data for the Voice Response System (VRS) from SV8300 CF

Memory to SV9300 Flash ROM Memory.................................................................................................. 6

CHAPTER 2 MIGRATION PROCEDURE........................................................................................................ 7

For Single Unit Configuration ....................................................................................................................... 7

For Multiple Unit Configuration and Remote Unit System ......................................................................... 11

Procedure to Save Voice Data (CF Memory)............................................................................................. 16

Procedure to Load Voice Data from CPU Built-in Memory (SRAM) .......................................................... 17

Procedure to Load Voice Data from CF Memory ....................................................................................... 18

To Migrate the System Data for the System Speed Dialing (300 Memories) ............................................ 19

For Non-Tenant-Basis Operation ............................................................................................................ 19

For Tenant-Basis Operation .................................................................................................................... 20

- ii -

CHAPTER 1 OUTLINE

Function Overview

SV9300 provides a procedure to migrate from an existing SV8300 to SV9300 system.

The system migration is performed by converting the system data assigned to the exiting SV8300 into

scripts for SV9300, including the phone number information and the setting information for service

features.

To convert the system data from SV8300 to SV9300 for the migration "System Data Conversion Tool"

supplied with SV9300 PCPro is used. For details of the "System Data Conversion Tool", refer to the SV9300

PC Programming Manual.

- 1 -

CHAPTER 1 OUTLINE

Required Equipment

The required equipment for the migration is shown in the table below.

Other equipment is available for SV9300 with a few exceptions. For details, see (12) in ‘Migration

Conditions’. Page 5

Equipment Description Remarks

CHS1UG(S)-xx NOTE 1

CPU Chassis

For SV9300

CHS2UG(D)-xx NOTE 1

Dual CPU Chassis

For SV9300

CC-CP10-A NOTE 1

CPU Blade

For SV9300

－

SV9300 Software Licenses NOTE 2

Several SV9300 Licenses are required

depending on the office conditions.

SV93 PC-PRO

Maintenance Tool (PCPro) for

SV9300

Necessary not only to convert the

system data but also to set SV9300

system data after the conversion.

SV83 PC-PRO

Maintenance Tool (PCPro) for

SV8300

Necessary to store the SV8300 system

data before converting it to SV9300.

NOTE 1: For preventive maintenance of the power supply, replacing the SV8300 chassis with SV9300 chassis is

recommended.

NOTE 2: For the migration of SV8300 TDM blades the Hardware Migration License is required.

- 2 -

CHAPTER 1 OUTLINE

Migration Conditions

Conditions for Migration from SV8300 to SV9300 System

(1) SV8300 system can be migrated to SV9300, regardless of its software version.

However, the required software version is SV8300 R7 or after, if the Voice Response System (VRS)

data is stored in the CPU built-in memory (SRAM) and the VRS data needs to be migrated to

SV9300.

(2) SV9300 CPU blade CC-CP10-A is required for migration.

(3) For the migration of SV8300 TDM blades the Hardware Migration License is required.

(4) The PCPro software for SV9300 and SV8300 is required. SV9300 and SV8300 PCPro can be installed

on the same PC.

- Use SV9300 PCPro to maintain system data after converting to SV9300. SV9300 PCPro is not

available to maintain the SV8300 system data.

- Use SV8300 PCPro to maintain SV8300 system data. SV8300 PCPro is not available to maintain the

SV9300 system data.

(5) When converting system data from SV8300 to SV9300 be sure to save all the SV8300 system data in

advance. Use the “System Data Conversion Tool” supplied with SV9300 PCPro for database

conversion.

The SV8300 system data saved before the conversion cannot be loaded directly to the SV9300

system.

(6) Because the system data below is not subject to the conversion with the System Data Conversion

Tool, manually set the data again after the conversion to SV9300.

SV8300 System Data that are not Subject to Conversion

SV9300 System Data

for Manual Setting

CM03

CME7

Password Level

CME7

CME9

Password

CME9

CM72 Y=0

NOTE

Called Party Number for System Speed Dialing (300

memories)

CM74 Y=0

CM72 Y=1

NOTE

Called Party Name for System Speed Dialing (300

memories): Called Party Name Registration by entering

character codes from PCPro/CAT

CM74 Y=1

CM72 Y=2

NOTE

Called Party Name for System Speed Dialing (300

memories) : Called Party Name Registration by

entering characters from PCPro

CM74 Y=2

CM72 Y=4

NOTE

Called Party Name for System Speed Dialing (300

memories): Called Party Name Registration by entering

character codes from PCPro/CAT (for Russian)

CM74 Y=4

Called Party Name for System Speed Dialing/Station

Speed Dialing: Called Party Name Registration by

entering character codes from PCPro/CAT (for Russian)

CM74 Y=4

CM77 Y=5

Station Name assignment with character

codes from PCPro/CAT (for Russian)

CM77 Y=5

CM9A Y=18

Setting of Soft Key name for each Pattern

Number (for Russian)

CM9A Y=18

Continued on next page

- 3 -

CHAPTER 1 OUTLINE

SV8300 System Data that are not Subject to Conversion

SV9300 System Data

for Manual Setting

CM40 Y=08

RS-232C Data speed

CM40 Y=08

CME6 Y=50

Mobile phone number link up with a Mobility Acces

s station number

CME6 Y=50

CMF6 Y=2

MP-FP command output setting (for realtime mode)

CMF6 Y=2

NOTE: When migrating the system data for the System Speed Dialing (300 memories), see `To

Migrate the System Data for the System Speed Dialing (300 Memories)’. Page 19

(7) Differences between SV8300 and SV9300 system data including initial value changes in some

commands. Such differences are automatically converted by using System Data Conversion Tool.

The converted system data can be confirmed in a report issued from the System Data Conversion

Tool.

(8) The following service settings that have been assigned by users are converted by the System Data

Conversion Tool.

- Station Speed Dialing

- One Touch Key Calling

- Call Forwarding-All Calls

- Call Forwarding-Busy Line

- Call Forwarding-No Answer

- Call Forwarding-Logout

- Elapsed time before Call Forwarding-No Answer for internal call

(9) The following service settings that have been assigned by users are not converted by the System

Data Conversion Tool. Set the data again after conversion to SV9300.

- Timed Reminder (Automatic Wake Up)

- Do Not Disturb

- Message Waiting

- Timed Queue

- Call Answer Preset

- Switching of Multiline Terminal Ringing Tones

- Setting Status for OAI SSFR (Service Set Facility Request)

- Multiline Terminal Display Enhancement for Universal Design

- Dual Ringing

- Message Reminder

- Call Restriction/Room Cutoff

- Busy Out from ACD/UCD group

- Voice Mail Live Record

- Split Call Forwarding-All Calls/Busy Line/No Answer

- Access Code Number Setting in Mobility Access Mode

- Reverse Contrast on the LCD

- Protection Mode for DT700 Series

- Mobility Access Mode

- Mobile Phone Number Link up with a Mobility Access Station Number/Destination of ISDN

Alternative Routing (station basis)

(10) The following data cannot be migrated.

- Outgoing/Incoming Call History

- Billing data

- 4 -

Otros manuales para Univerge SV9300

Tabla de contenidos

Otros manuales de Hardware de computadora de NEC

NEC

NEC N8105-64 Manual de usuario

NEC

NEC N8154-24 Manual de usuario

NEC

NEC N8151-128 Guía del usuario

NEC

NEC IE-789801-NS-EM1 Manual de usuario

NEC

NEC N8103 Series Instrucciones de funcionamiento

NEC

NEC IE-784000-R Manual de usuario

NEC

NEC PD754144 Manual de usuario

NEC

NEC Exastro ITA Manual del operador

NEC

NEC N8105-54 Manual de usuario

NEC

NEC N8151-50A Manual de usuario

NEC

NEC N8151-143 Manual de usuario

NEC

NEC N8151-103 Guía del usuario

NEC

NEC N8104-206 Manual de usuario

NEC

NEC N8405-019 Manual de usuario

NEC

NEC Express5800/B120f Manual de usuario

NEC

NEC IE-78K0-NS-P04 Manual de usuario

NEC

NEC NEC PD78081(A) Manual de usuario

NEC

NEC N8106-019 VMware ESXi Manual de usuario

NEC

NEC 455-01593-000 Manual de usuario

NEC

NEC N8105-53 Manual de usuario

NEC

NEC N8105-55 Manual de usuario

NEC

NEC N8104-213 Manual de usuario

NEC

NEC N8151-60 Manual de usuario

NEC

NEC PD75402A Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario