National Instruments FieldPoint cFP-1808 Manual de usuario

cFP-1808

Quick Start Guide

Compact FieldPoint cFP-1808

What You Need to Get Set Up

1. Mount the cFP-1808

You can mount the cFP-1808 on a panel or in a standard 19 in. rack. Before using

either of these mounting methods, record the serial number from the back of the

cFP-1808.

Each set of mounting instructions in this document includes an instruction to

connect the protective earth (PE) ground terminal on the cFP-1808 to the system

safety ground. The PE ground terminal has the following symbol stamped beside

it: . Connect the PE ground terminal to the system safety ground using 14 AWG

• cFP-1808 Network Interface

• Mounting hardware (DIN rail,

panel-mount, or rack-mount

accessory)

• I/O module(s)

• Connector blocks and/or cables

• Ethernet or serial cable

• 11–30 VDC power supply

• Accessories: Ethernet cable,

number 2 Phillips screwdriver

• PC running Windows

• FieldPoint software 4.1.2 or later

™

cFP-1808 Quick Start Guide 2 ni.com

(1.6 mm) wire with a ring lug. Use the 5/16 in. panhead screw shipped with the

backplane to secure the ring lug to the PE ground terminal.

Caution Keep in mind these requirements for space and cabling

clearance:

• Allow at least 51 mm (2 in.) all around the cFP-1808 for air

circulation.

• Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the I/O

modules.

127 mm

(5.00 in.)

441 mm

(17.36 in.)

Caution If you are using UL Recognized I/O modules with the Compact

FieldPoint system, you must install the entire system in a suitably rated,

UL Listed NEMA or IP enclosure. Refer to the Compact FieldPoint

Safety Information section for more information.

Cooling

Outline

51 mm

(2.00 in.)

88 mm (3.46 in.)

69 mm

(2.72 in.)

76 mm

(3.00 in.)

Cabling

Clearance

441 mm

(17.36 in.) Cooling

Outline

51 mm

(2.00 in.)

cFP-1808 Quick Start Guide 4 ni.com

Caution NI recommends that you use one of the mounting systems

described in this document. If you decide to use a custom mounting

solution, make sure that the screws you use are short enough to fit in the

holes in the backplane. The screw holes are 5 mm (0.2 in.) deep.

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

Mounting the Backplane on a Panel

1. Fasten the panel-mount plates to the back of the cFP-1808 using a number 2

Phillips screwdriver and the 8-32 ×

5/16 in. countersunk screws shipped with

the kit.

Caution Do not use screws longer than 5/16 in. to fasten the

panel-mount plates to the backplane.

cFP-1808 Quick Start Guide 6 ni.com

2. Bolt or screw the panel-mount accessory to a panel.

3. Connect the PE ground terminal on the cFP-1808 to safety ground.

Caution Disconnect power before removing the backplane from the

panel.

457 mm (18 in.)

127 mm

(5 in.)

476 mm (18.7 in.)

102 mm

(4 in.)

2. Install I/O Modules on the Backplane

1. Align the captive screws on the

I/O module with the holes on the

backplane.

2. Press firmly to seat the I/O

module on the backplane.

3. Using a number 2 Phillips

screwdriver with a shank of at

least 64 mm (2.5 in.) length,

tighten the captive screws to

1.1 N · m (10 lb · in.) of torque.

4. Repeat this procedure to install

additional I/O modules on the

backplane.

3. Install Connector Blocks on the Backplane

In order to connect I/O modules to input signals or to external loads, you need to

install a cFP-CB-xconnector block or other connectivity accessory for each I/O

module on the backplane. Use the connector socket to the right of each I/O module

socket.

Caution Do not insert or remove connector blocks or other connectivity

accessories while power is applied to them.

cFP-1808 Quick Start Guide 8 ni.com

1. Wire field devices as described in the I/O

module and connector block operating

instructions.

Caution Hazardous voltage wiring

should be performed by qualified

personnel and in accordance with

local electrical standards.

2. Align the captive screws on the connector

block with the holes on the backplane.

3. Press firmly to seat the connector block on

the backplane.

4. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.)

length, tighten thecaptive screws to 1.1 N · m (10 lb · in.) of torque.

5. Repeat this procedure to install additional connector blocks on the backplane.

4. Connect the cFP-1808 to Your Network

You can connect the cFP-1808 to an Ethernet network, an RS-232 network, or

both.

Connecting the cFP-1808 to an Ethernet Network

In order to use the cFP-1808 on an Ethernet network, you must first configure the

cFP-1808 using MAX.

Connect the cFP-1808 to an Ethernet network using the RJ-45 Ethernet port on the

controller. Use a standard Category 5 Ethernet cable to connect the cFP-1808 to

an Ethernet hub, or use an Ethernet crossover cable to connect the controller

directly to a computer. Refer to Cabling in the Specifications section for pinouts

of the two types of Ethernet cable.

If the host PC is already configured on a network, you must configure the

cFP-1808 on the same network. If neither is connected to a network, you can

connect the two directly using a crossover cable.

In order for you to configure the cFP-1808, it must reside on the same subnet as

the host PC.

Caution To prevent data loss and to maintain the integrity of your

Ethernet installation, do not use a cable longer than 100 m. If you are

using a 100 Mbps Ethernet, National Instruments recommends using a

Category 5 shielded twisted-pair Ethernet cable.

Connecting the cFP-1808 to an RS-232 Serial Network

In order to use the cFP-1808 on a serial network, you must first connect it to a host

computer and configure it using MAX. Connect the RS-232 port of the cFP-1808

to the RS-232 port of the host computer. Use a 9-pin D-SUB male-to-female

straight-through cable. Do not use a null modem cable (usually female-to-female).

DIP switches 3–5 set the baud rate. Table 1 shows the switch positions and the

corresponding network baud rates.

Note The preconfigured setting of 115.2 kbps provides the fastest

performance, and you do not need to change this setting unless you

experience communication problems.

Otros manuales para FieldPoint cFP-1808

Tabla de contenidos

Otros manuales de Sistema de E/S de National Instruments

National Instruments

National Instruments NI-9477 Manual de usuario

National Instruments

National Instruments 9218 Manual

National Instruments

National Instruments USB-9265 Manual de usuario

National Instruments

National Instruments PXIe-5764 Manual del propietario

National Instruments

National Instruments NI 9251 Manual

National Instruments

National Instruments 9425E Manual de usuario

National Instruments

National Instruments NI 9231 Manual de usuario

National Instruments

National Instruments PXI-7854 Manual de usuario

National Instruments

National Instruments NI 9237E Series Manual de usuario

National Instruments

National Instruments NI R Series Manual de usuario

National Instruments

National Instruments SC-2071 Manual de usuario

National Instruments

National Instruments NI 9234E Manual de usuario

National Instruments

National Instruments PXIe-7867R Manual de usuario

National Instruments

National Instruments R Series Manual de usuario

National Instruments

National Instruments NI 9381 Manual de usuario

National Instruments

National Instruments NI 9437 Manual de usuario

National Instruments

National Instruments NI 9208E Manual de usuario

National Instruments

National Instruments 9262 Manual de usuario

National Instruments

National Instruments 9232 Manual de usuario

National Instruments

National Instruments 9216 Manual

National Instruments

National Instruments NI PCI-6510 Manual de usuario

National Instruments

National Instruments PCIe-6374 Manual del propietario

National Instruments

National Instruments NI 9423 Manual de usuario

National Instruments

National Instruments NI 9222 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario