National Instruments 9262 Manual de usuario
GETTING STARTED GUIDE
NI 9262
1 MS/s/ch Simultaneous, ±10 V, 6-Channel
C Series Voltage Output Module
This document explains how to connect to the NI 9262.
Note Before you begin, complete the software and
hardware installation procedures in your chassis
documentation.
Note The guidelines in this document are specific to
the NI 9262. The other components in the system might
not meet the same safety ratings. Refer to the
documentation for each component in the system to
determine the safety and EMC ratings for the entire
system.
Safety Guidelines
Operate the NI 9262 only as described in this document.
Caution This icon denotes a caution, which advises
you to consult documentation where this symbol is
marked.
Caution Do not operate the NI 9262 in a manner not
specified in this document. Product misuse can result in
a hazard. You can compromise the safety protection
2| ni.com | NI 9262 Getting Started Guide
built into the product if the product is damaged in any
way. If the product is damaged, return it to NI for
repair.
Safety Guidelines for Hazardous Voltages
If hazardous voltages are connected to the device, take the
following precautions. A hazardous voltage is a voltage greater
than 42.4 Vpk voltage or 60 V DC to earth ground.
Caution Ensure that hazardous voltage wiring is
performed only by qualified personnel adhering to local
electrical standards.
Caution All wiring must be insulated for the highest
voltage used.
Caution Do not mix hazardous voltage circuits and
human-accessible circuits on the same module.
Caution Ensure that devices and circuits connected to
the module are properly insulated from human contact.
Caution When module terminals are hazardous
voltage LIVE (>42.4 Vpk/60 V DC), you must ensure
NI 9262 Getting Started Guide | © National Instruments | 3
that devices and circuits connected to the module are
properly insulated from human contact.
NI 9262 Safety Voltages
Connect only voltages that are within the following limits.
AO-to-COM ±30 V maximum
Isolation
Channel-to-channel None
Channel-to-earth ground
Continuous 60 V DC,
Measurement Category I
Withstand 1,000 V RMS, verified by a 5 s
dielectric withstand test
Measurement Category I is for measurements performed on
circuits not directly connected to the electrical distribution system
referred to as MAINS voltage. MAINS is a hazardous live
electrical supply system that powers equipment. This category is
for measurements of voltages from specially protected secondary
circuits. Such voltage measurements include signal levels, special
4| ni.com | NI 9262 Getting Started Guide
equipment, limited-energy parts of equipment, circuits powered
by regulated low-voltage sources, and electronics.
Caution Do not connect the NI 9262 to signals or use
for measurements within Measurement Categories II,
III, or IV.
Note Measurement Categories CAT I and CAT O are
equivalent. These test and measurement circuits are for
other circuits not intended for direct connection to the
MAINS building installations of Measurement
Categories CAT II, CAT III, or CAT IV.
Safety Guidelines for Hazardous Locations
The NI 9262 is suitable for use in Class I, Division 2, Groups A,
B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4
Gc and Ex nA IIC T4 Gc hazardous locations; and nonhazardous
locations only. Follow these guidelines if you are installing the
NI 9262 in a potentially explosive environment. Not following
these guidelines may result in serious injury or death.
Caution Do not disconnect I/O-side wires or
connectors unless power has been switched off or the
area is known to be nonhazardous.
NI 9262 Getting Started Guide | © National Instruments | 5
Caution Do not remove modules unless power has
been switched off or the area is known to be
nonhazardous.
Caution Substitution of components may impair
suitability for Class I, Division 2, or Zone 2.
Caution The system must be installed in an enclosure
certified for the intended hazardous (classified)
location, having a tool secured cover/door, where a
minimum protection of at least IP54 is provided.
Special Conditions for Hazardous Locations Use in
Europe and Internationally
The NI 9262 has been evaluated as Ex nA IIC T4 Gc equipment
under DEMKO 12 ATEX 1202658X and is IECEx UL 14.0089X
certified. Each NI 9262 is marked II 3G and is suitable for use
in Zone 2 hazardous locations, in ambient temperatures of -40 °C
≤ Ta ≤ 70 °C. If you are using the NI 9262 in Gas Group IIC
hazardous locations, you must use the device in an NI chassis that
has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or
Ex nL IIC T4 equipment.
6| ni.com | NI 9262 Getting Started Guide
Caution Transient protection shall be provided that is
set at a level not exceeding 140% of the peak rated
voltage value of 85 V at the supply terminals to the
equipment.
Caution The system shall only be used in an area of
not more than Pollution Degree 2, as defined in
IEC/EN 60664-1.
Caution The system shall be mounted in an
ATEX/IECEx-certified enclosure with a minimum
ingress protection rating of at least IP54 as defined in
IEC/EN 60079-15.
Caution The enclosure must have a door or cover
accessible only by the use of a tool.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory
requirements and limits for electromagnetic compatibility (EMC)
stated in the product specifications. These requirements and
limits provide reasonable protection against harmful interference
when the product is operated in the intended operational
electromagnetic environment.
NI 9262 Getting Started Guide | © National Instruments | 7
This product is intended for use in industrial locations. However,
harmful interference may occur in some installations, when the
product is connected to a peripheral device or test object, or if the
product is used in residential or commercial areas. To minimize
interference with radio and television reception and prevent
unacceptable performance degradation, install and use this
product in strict accordance with the instructions in the product
documentation.
Furthermore, any changes or modifications to the product not
expressly approved by National Instruments could void your
authority to operate it under your local regulatory rules.
Caution To ensure the specified EMC performance,
operate this product only with a double-shielded cable.
Connect the inner shield to COM and the outer shield
to chassis.
Special Conditions for Marine Applications
Some products are Lloyd’s Register (LR) Type Approved for
marine (shipboard) applications. To verify Lloyd’s Register
certification for a product, visit ni.com/certification and search
for the LR certificate, or look for the Lloyd’s Register mark on
the product.
8| ni.com | NI 9262 Getting Started Guide
Caution In order to meet the EMC requirements for
marine applications, install the product in a shielded
enclosure with shielded and/or filtered power and
input/output ports. In addition, take precautions when
designing, selecting, and installing measurement probes
and cables to ensure that the desired EMC performance
is attained.
Preparing the Environment
Ensure that the environment in which you are using the NI 9262
meets the following specifications.
Operating temperature
(IEC 60068-2-1, IEC 60068-2-2)
-40 °C to 70 °C
Operating humidity
(IEC 60068-2-78)
10% RH to 90% RH,
noncondensing
Pollution Degree 2
Maximum altitude 5,000 m
Indoor use only.
Note Refer to the device datasheet on ni.com/manuals
for complete specifications.
NI 9262 Getting Started Guide | © National Instruments | 9
NI 9262 Pinout
COM
COM
COM
COM
COM
COM
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
AO0
AO1
AO2
AO3
AO4
AO5
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
COM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
10 | ni.com | NI 9262 Getting Started Guide
Tabla de contenidos
Otros manuales de Sistema de E/S de National Instruments
National Instruments
National Instruments NI 9236 Manual de usuario
National Instruments
National Instruments NI-9228 Manual
National Instruments
National Instruments NI 9263 Manual de usuario
National Instruments
National Instruments SCXI-1120/D Manual de usuario
National Instruments
National Instruments NI USB-9229 Manual de usuario
National Instruments
National Instruments FieldPoint FP-DO-410 Manual de usuario
National Instruments
National Instruments NI USB-9219 Manual de usuario
National Instruments
National Instruments Data Acquisition Device E Series Manual de usuario
National Instruments
National Instruments 8-Channel Solid-State Relay (SSR) Digital Output NI... Manual de usuario
National Instruments
National Instruments NI SCB-68 HSDIO Manual de instrucciones
National Instruments
National Instruments FOUNDATION Manual de usuario
National Instruments
National Instruments NI 653 Series Manual de usuario
National Instruments
National Instruments REM-11154 Manual de usuario
National Instruments
National Instruments SCB-68 Manual de usuario
National Instruments
National Instruments NI 9469 Manual de usuario
National Instruments
National Instruments 9215E Manual de usuario
National Instruments
National Instruments R Series Intelligent DAQ PCI/PXI-783xR Manual de usuario
National Instruments
National Instruments sbRIO-9229 Manual de usuario
National Instruments
National Instruments NI 9205 Manual de usuario
National Instruments
National Instruments PC-TIO-10 Manual de usuario
Manuales populares de Sistema de E/S de otras marcas
WAGO
WAGO 750-344 Manual de usuario
Teknim
Teknim TWM-1887 Manual de instrucciones
Intelligent Appliance
Intelligent Appliance IA-2662-E Manual de usuario
BERGHOF
BERGHOF ECC DIO 16/16 Manual de instrucciones
Advantech
Advantech PCM-27J3AU Manual de instalación y operación
Festo
Festo CP-E08-M12-CL Manual de usuario
