National Instruments SCXI-1181K Manual de usuario

371063A-01 © 1994 National Instruments Corporation. All rights reserved August 1998

Installation Guide

SCXI-1181K Custom Module Assembly

This guide documents the contents of your SCXI-1181K custom module assembly kit and

includes illustrations of the circuit board specifications and the module assembly.

Introduction

The SCXI-1181K custom module assembly kit includes the unassembled components you need

to build a custom SCXI module, but not the actual circuit board. All of the mechanical

components of an SCXI module, such as the metal enclosure, front and back panels, and

connectors, are included.

The SCXI-1181K is intended for developers of custom SCXI modules who design and lay out

custom circuit boards for modules. For prototyping or building low-volume custom SCXI

modules, the fully assembled SCXI-1181 breadboard moduleis more appropriate.

What Your Kit Should Contain

The SCXI-1181K custom module assembly kit (part number 776572-81K) contains the

components listed in the following table. The reference numbers in the left column of the table

refer to callouts in Figure 1.

Reference

Number Component Quantity

1 Module front panel 1

2

3 Thumb screw, 2.5 mm 2

4 #4 x 5/16 in. Phillips screw, flat head 2

5 Enclosure base 1

6 Module rear panel 1

7 #4 x 5/16 in. Phillips screw, pan head 3

8 Enclosure cover 1

9 Identification label 1

J1 3 x 32 position Deutsche Industrie Norme

connector header 1

J2 50 position connector header 1

P1 4 x 6, 2 mm connector, push-fit 4

— Installation guide 1

1

Module front panel overlay

SCXI-1181K Custom Module Assembly Install. Guide 2 © National Instruments Corporation

Refer to the reference numbers of the components in the previous table and the corresponding

components in Figure 1 for module assembly.

Note: The four P1 connectors have a push-fit peg. Secure the P1 connectors to the printed

wire circuit board (PWB) by pushing the connector onto the PWB so that the middle

peg of the connector presses into the 0.081 in. hole in the PWB. National Instruments

recommends using the push-fit peg hand tool (part number CTHT-200) manufactured

by ITT Cannon for this installation. You can contact ITT Cannon at (800) 845-7000.

Figure 2 shows the SCXI module PWB outline.

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Unidad de control de National Instruments

National Instruments

National Instruments Network Adapter NI PXIe-6672 Manual de usuario

National Instruments

National Instruments NI-5783 Manual de usuario

National Instruments

National Instruments C Series Manual de usuario

National Instruments

National Instruments SCC-TC Series Manual de usuario

National Instruments

National Instruments VXI-8340 Series Manual de usuario

National Instruments

National Instruments NI 9225 Manual

National Instruments

National Instruments FP-AI-102 Manual de usuario

National Instruments

National Instruments FieldPoint FP-AI-110 Manual de usuario

National Instruments

National Instruments FieldPoint cFP-DI-304 Manual de usuario

National Instruments

National Instruments NI 9212 Manual de usuario

National Instruments

National Instruments PXImc Series Manual de usuario

National Instruments

National Instruments REM-11102 Manual de usuario

National Instruments

National Instruments NI 9235 Manual de usuario

National Instruments

National Instruments NI DCM-2316 Manual de usuario

National Instruments

National Instruments NI 9218 Manual de usuario

National Instruments

National Instruments NI 9251 Manual de usuario

National Instruments

National Instruments 9501 C Series Manual de usuario

National Instruments

National Instruments FieldPoint FP-1000 Manual de usuario

National Instruments

National Instruments PXIe-8238 Manual de usuario

National Instruments

National Instruments PXIe-5693 Manual

National Instruments

National Instruments NI PXI/e-4000 Series Manual de usuario

National Instruments

National Instruments NI 9242 Manual de usuario

National Instruments

National Instruments NI 9861 Manual de usuario

National Instruments

National Instruments SCC-DO01 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario