National Instruments FieldPoint cFP-DI-304 Manual de usuario
Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | sales@artisantg.com | www.artisantg.com
SM
View
Instra
FieldPoint™Operating Instructions
cFP-DI-304
32-Channel, 24 VDC Sinking Digital Input Module
These operating instructions describe how to install and use
the cFP-DI-304 digital input module. For information about
configuring and accessing the cFP-DI-304 over a network, refer to
the user manual for the FieldPoint network module you are using.
Features
The cFP-DI-304 is a FieldPoint digital input module with the
following features:
• 32 sinking digital input channels
• Compatible with 24 VDC sourcing-output devices
• Inputs protected up to 30 VDC (up to 60 VDC on up to
eight channels)
•250V
rms CAT II continuous channel-to-ground isolation,
verified by 2,300 Vrms , 5 s dielectric withstand test
• On/off LED indicators
• Hot swappable
Installing the cFP-DI-304
The cFP-DI-304 mounts on a Compact FieldPoint backplane
(cFP-BP-x), which provides operating power to the module.
Installing the cFP-DI-304 onto a powered backplane does not
disrupt the operation of the FieldPoint bank.
To install the cFP-DI-304, refer to Figure 1 and complete the
following steps:
1. Align the captive screws on the cFP-DI-304 with the holes on
the backplane. The alignment keys on the cFP-DI-304 prevent
backward insertion.
2. Press firmly to seat the cFP-DI-304 on the backplane.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
cFP-DI-304 2 ni.com
3. Using a number 2 Phillips screwdriver with a shank of at least
64 mm (2.5 in.) length, tighten the captive screws to 1.1 N ⋅m
(10 lb ⋅in.) of torque. The nylon coating on the screws prevents
them from loosening.
Figure 1. Installing the cFP-DI-304
1cFP-DI-304
2CaptiveScrews
3 cFP Controller Module
4ScrewHoles
5 cFP-BP-x Backplane
2
2
1
3 5
4
4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 3 cFP-DI-304
Mounting the System Upright
To ensure maximum cooling efficiency, mount the Compact
FieldPoint system so that the I/O module vents are at the top and
bottom as shown in Figure 2.
Figure 2. Mounting the System Upright
Wiring the cFP-DI-304
The cFP-CB-1 has connections for each of the 32 input channels.
You can use the cFP-CB-3, but it has connections for only
16 channels. Each channel has one input terminal, VIN.
Table 1 lists the VIN terminal assignment for each channel.
Table 1. Terminal Assignments
Channel VIN Term in al
0 1
1 2
2 3
3 4
4 5
5 6
6 7
7 8
8 9
910
Up
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
cFP-DI-304 4 ni.com
You can wire each channel for use with a sourcing-output device.
A sourcing-output device provides a path to a voltage source.
10 11
11 12
12 13
13 14
14 15
15 16
16 17
17 18
18 19
19 20
20 21
21 22
22 23
23 24
24 25
25 26
26 27
27 28
28 29
29 30
30 31
31 32
Table 1. Terminal Assignments (Continued)
Channel VIN Term in al
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 5 cFP-DI-304
Figure 3 shows how to connect a sourcing-output device to one
channel of the cFP-DI-304.
Figure 3. Sourcing-Output Device Connected to One Channel
Note You must ground all connected devices to the
C terminals.
Digital Input Circuitry
The cFP-DI-304 has 32 input channels. You can connect a voltage
signal to each channel. All 32 input channels share a common
ground reference that is isolated from other modules in the
FieldPoint system.
When you apply a voltage above 10 V to a VIN terminal, current
flows through that terminal and the channel is ON. When you
apply a voltage below 5 V to a VIN terminal, the channel is OFF.
When you apply a voltage between 5 and 10 V, the channel may be
ON or OFF.
The cFP-DI-304 has sinking inputs, which means that current
flows through the VIN terminal to the input circuitry. The inputs are
compatible with sourcing-output devices capable of sourcing
or driving current from a positive supply voltage to common.
A sensor is an example of a sourcing-output device.
Make sure that devices you connect to the cFP-DI-304 have OFF
state leakage currents of less than 150 µA to ensure that they do not
provide false ON state readings to the cFP-DI-304.
C
V
IN
Input
Circuitry
Sourcing-
Output
Device
cFP-DI-304
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
cFP-DI-304 6 ni.com
Status Indicators
The cFP-DI-304 has two green status LEDs, POWER and
READY. After you insert the cFP-DI-304 into a backplane and
apply power to the connected network module, the green POWER
indicator lights and the cFP-DI-304 informs the network module
of its presence. When the network module recognizes the
cFP-DI-304, it sends initial configuration information to the
cFP-DI-304. After the cFP-DI-304 receives this initial information,
the green READY indicator lights and the module is in normal
operating mode.
In addition to the POWER and READY lights, each channel has a
numbered green status indicator that lights when the channel is in
the ON state.
Upgrading the FieldPoint Software
In order to use the cFP-DI-304, you must have FieldPoint software
version 5.0 or later installed on the host computer. Go to
ni.com/support, select Drivers and Updates»Current
Versions»Distributed I/O—FieldPoint, and select the latest
version under Driver.
Upgrading the FieldPoint Firmware
You may need to upgrade the FieldPoint firmware when you add
new I/O modules to the FieldPoint system. For information about
determining which firmware you need and how to upgrade your
firmware, go to ni.com/info and enter fpmatrix.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 7 cFP-DI-304
Isolation and Safety Guidelines
Caution Read the following information before
attempting to connect the cFP-DI-304 to any circuits
that may contain hazardous voltages.1
This section describes the isolation of the cFP-DI-304 and
its compliance with international safety standards. The field
wiring connections are isolated from the backplane and the
inter-module communication bus. The isolation barriers in the
module provide 250 Vrms Measurement Category II continuous
channel-to-backplane and channel-to-ground isolation, verified
by a 2,300 Vrms , 5 s dielectric withstand test.2The cFP-DI-304
provides double insulation compliant with IEC 61010-1 for
working voltages of 250 Vrms.3Safety standards (such as those
published by UL and IEC) require the use of double insulation
between hazardous voltages and any human-accessible parts or
circuits.
Never try to use any isolation product between human-accessible
parts (such as DIN rails or monitoring stations) and circuits that
can be at hazardous potentials under normal conditions, unless the
product is specifically designed for such an application, as is the
cFP-DI-304.
Even though the cFP-DI-304 is designed to handle applications
with hazardous potentials, follow these guidelines to ensure a safe
total system:
•There is no isolation between channels on the cFP-DI-304. If a
hazardous voltage is present on any channel, all channels are
considered hazardous. Make sure that all other devices and
circuits connected to the module are properly insulated from
human contact.
•Do not share the external supply voltages (the V and
C terminals) with other devices, including other FieldPoint
devices, unless those devices are isolated from human contact.
1 A hazardous voltage is a voltage greater than 42.4 Vpeak or 60 VDC. When a
hazardous voltage is present on any channel, all of the channels must be considered
to be carrying hazardous voltages. Ensure that all circuits connected to the module
are inaccessible to human touch.
2 Refer to the Safety Isolation Voltage section for more information about isolation on
the cFP-DI-304.
3 Working voltage is defined as the signal voltage plus the common-mode voltage.
Common-mode voltage is the voltage of the module with respect to ground.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
cFP-DI-304 8 ni.com
•For Compact FieldPoint, you must connect the protective earth
(PE) ground terminal on the cFP-BP-xbackplane to the system
safety ground. The backplane PE ground terminal has the
following symbol stamped beside it: . Connect the
backplane PE ground terminal to the system safety ground
using 14 AWG (1.6 mm) wire with a ring lug. Use the 5/16 in.
panhead screw shipped with the backplane to secure the ring
lug to the backplane PE ground terminal.
•As with any hazardous voltage wiring, make sure that all
wiring and connections meet applicable electrical codes and
commonsense practices. Mount terminal bases and backplanes
in an area, position, or cabinet that prevents accidental or
unauthorized access to wiring that carries hazardous voltages.
•Do not use the cFP-DI-304 as the only isolating barrier
between human contact and working voltages higher than
250 Vrms .
•Operate the cFP-DI-304 only at or below Pollution Degree 2.
Pollution Degree 2 means that only nonconductive pollution
occurs in most cases. Occasionally, however, temporary
conductivity caused by condensation must be expected.
•Operate the cFP-DI-304 at or below Measurement Category II.
Measurement Category II is for measurements performed on
circuits directly connected to the low-voltage installation.
This category refers to local-level distribution, such as that
provided by a standard wall outlet.
Safety Guidelines for Hazardous Locations
The cFP-DI-304 is suitable for use in Class I, Division 2, Groups
A, B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nC IIC
T4 and Ex nC IIC T4 hazardous locations; and nonhazardous
locations only. Follow these guidelines if you are installing the
cFP-DI-304 in a potentially explosive environment. Failing to
follow these guidelines may result in serious injury or death.
Caution Do not disconnect I/O-side wires or connectors
unless power has been switched off or the area is known
to be nonhazardous.
Caution Do not remove modules unless power has been
switched off or the area is known to be nonhazardous.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
© National Instruments Corp. 9 cFP-DI-304
Caution Substitution of components may impair
suitability for Class I, Division 2.
Caution For Zone 2 applications, install the Compact
FieldPoint system in an enclosure rated to at least IP 54
as defined by IEC 60529 and EN 60529.
Caution For Zone 2 applications, connected signals must
be within the following limits:
Capacitance .......................... 0.2 µF max
Special Conditions for Safe Use in Europe
This equipment has been evaluated as EEx nC IIC T4 equipment
under DEMKO Certificate No. 03 ATEX 0251502X. Each module
is marked II 3G and is suitable for use in Zone 2 hazardous
locations.
Safety Guidelines for Hazardous Voltages
If hazardous voltages are connected to the module, take the
following precautions:
Caution Ensure that hazardous voltage wiring is
performed only by qualified personnel adhering to local
electrical standards.
Caution Do not mix hazardous voltage circuits and
human-accessible circuits on the same module.
Caution Make sure that devices and circuits connected to
the module are properly insulated from human contact.
Caution When terminals on the connector block are live
with hazardous voltages, make sure that the terminals are
not accessible.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Tabla de contenidos
Otros manuales de Unidad de control de National Instruments
National Instruments
National Instruments PXIe-4322 Manual de usuario
National Instruments
National Instruments SCC-DO01 Manual de usuario
National Instruments
National Instruments NI 9229 Manual
National Instruments
National Instruments NI PXIe-4140 Manual de usuario
National Instruments
National Instruments SCC-A10 Manual de usuario
National Instruments
National Instruments PXIe-4302 Manual
National Instruments
National Instruments FD-11634 Manual de usuario
National Instruments
National Instruments 9472 Manual de usuario
National Instruments
National Instruments SCC-PWR02 Manual de usuario
National Instruments
National Instruments FlexRIO PXIe-79 R Series Manual de usuario
National Instruments
National Instruments NI 9475 Manual de usuario
National Instruments
National Instruments NI FlexRIO PXI-7951R Manual de usuario
National Instruments
National Instruments VXI-8340 Series Manual de usuario
National Instruments
National Instruments PXIe-8830mc Manual de usuario
National Instruments
National Instruments NI 9871 Manual de usuario
National Instruments
National Instruments SCXI-1141 Manual de usuario
National Instruments
National Instruments NI 9207E Manual de usuario
National Instruments
National Instruments NI 9871 Manual de usuario
National Instruments
National Instruments PXI Terminal Block NI TB-2708 Manual de usuario
National Instruments
National Instruments NI 9401 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
