National Instruments NI WLS-9000 Series Manual de usuario

GETTING STARTED GUIDE

NI-DAQ™mx for NI WLS/ENET-9163

NI WLS/ENET-9000 Series Devices

This guide describes how to install and configure the NI-DAQmx software and

NI WLS/ENET-9000 Series data acquisition (DAQ) device (comprised of an

NI WLS/ENET-9163 carrier and NI C Series I/O module). This guide also

describes how to verify that the device is working properly.

Refer to the NI WLS/ENET-9163 User Guide and Specifications and your

C Series I/O module user guide for information about how to use your

NI WLS/ENET-9000 Series device.

You must be an Administrator to install NI software and devices on your computer.

Check for documentation updates at ni.com/manuals.

Pinouts and User Guides

All NI-DAQmx devices have a PDF user guide that contains pinouts. Go to

ni.com/manuals and search for your NI C Series I/O module.

ni.com/manuals

DeutschFrançais

NI-DAQmx for NI WLS/ENET-9163 Getting Started Guide 2 ni.com

Step 1. Install the Application Software and NI-DAQmx

Before installing your DAQ device, you must install the software you plan to use

with the device. Complete the following steps.

1. Install the NI application software, LabVIEW, LabWindows™/CVI™,

Measurement Studio, or LabVIEW SignalExpress, as described in the

installation instructions that accompany your software.

Note Back up any applications before upgrading software or modifying

the application.

2. Install the NI-DAQmx driver software before installing new devices so

Windows can detect them. Insert the disk, and complete the instructions,

including rebooting the computer. For troubleshooting instructions,

use the Hardware Installation/Configuration Troubleshooter at ni.com/

support/install.

Step 2. Unpack and Set Up the Device

The NI C Series I/O module and the NI WLS/ENET-9163 carrier are packaged

separately. Remove the packaging and inspect the devices. Contact NI if the

components appear damaged. Do not install a damaged device.

Caution The devices are static sensitive. Always properly ground

yourself and the equipment when handling or connecting to the devices.

Complete the following steps while referring to Figure 1 to install the C Series

I/O module into the NI WLS/ENET-9163 carrier.

Note Before installing the device, you must install the software, as

described in Step 1. Install the Application Software and NI-DAQmx.

Note Refer to the NI WLS/ENET-9163 User Guide and Specifications

for information about mounting and grounding the NI WLS/ENET-9163

carrier.

1. Make sure no cables/signals are connected to the C Series I/O module or the

NI WLS/ENET-9163 carrier. Remove any protective covers from the C Series

I/O module connector.

2. Align the C Series I/O module with the NI WLS/ENET-9163 carrier.

3. Squeeze the latches and insert the C Series I/O module into the

NI WLS/ENET-9163 carrier.

Figure 1. C Series I/O Module Installation

1 C Series I/O Module 2 NI WLS/ENET-9163 Carrier

NATIONAL

INSTRUMENTS

RESET

WLS

LINK

LINK/ACT

GND

PR0

PR1

10/100

INPUT 9-30 V

4.5 W MAX

NI WLS-9163

802.11g C SeriesCarrier

POWER

ACTIVE

STATU S

WLSLINK

ACTIVE

STATU S

POWER

NI-DAQmx for NI WLS/ENET-9163 Getting Started Guide 4 ni.com

4. Press firmly on the connector side of the C Series I/O module until the latches

lock the module into the NI WLS/ENET-9163 carrier, as shown in Figure 2.

Figure 2. Locking Module into Place

5. (NI WLS-9163 Carrier Only) Attach the supplied antenna as shown in Figure 3.

Figure 3. NI WLS-9163 Carrier Antenna Assembly

NATIONAL

INSTRUMENTS

RESET

LINK/ACT

GND

PR0

PR1

10/100

INPUT9-30 V

4.5W MAX

NIWLS-9163

802.11gC SeriesCarr ier

WLSLINK

ACTIVE

STATUS

P0WER

WLS

LINK

POWER

ACTIVE

STATUS

STATU S

POWER

ACTIVE

RESET

LINK/ACT

GND

PR0

PR1

10/100

INPUT 9-30 V

4.5 W MAX

WLS

LINK

WLSLINK

ACTIVE

STATU S

POWER

NI WLS-9163

802.11g C SeriesCarrier

6. Use a standard Category 5 Ethernet cable to connect the NI WLS/ENET-9000

Series device to an Ethernet network.1Connect one end to the RJ-45 Ethernet

port on the device, and the other end to an Ethernet hub or directly to your

computer. Refer to the NI WLS/ENET-9163 User Guide and Specifications for

information about the Ethernet cable.

7. Power the device using the included power adapter or other 9–30 VDC power

source.

The POWER and STATUS LEDs light. The POWER LED will light as long as

power is being supplied to the NI WLS/ENET-9000 Series device. Refer to the

NI WLS/ENET-9163 User Guide and Specifications for information about the

LEDs on the NI WLS/ENET-9163 chassis.

Step 3. Discover the Device

To discover the device, complete the following steps.

1. Launch Measurement & Automation Explorer (MAX).

2. Expand Devices and Interfaces, right-click Network Devices, and select

Find Network NI-DAQmx Devices.

1 You can either use a standard Category 5 Ethernet cable or an Ethernet crossover cable to connect the

NI WLS/ENET-9000 Series device directly to your computer.

NI-DAQmx for NI WLS/ENET-9163 Getting Started Guide 6 ni.com

If you plugged your device into an Ethernet port on your local subnet or

directly into your computer, the device should appear in the list of available

devices.

3. Put a checkmark next to your device in the Available Devices window and

click Add Selected Devices to add the device to MAX. The device will be

listed under Network Devices in the configuration tree.

If your device does not appear in Available Devices, wait until the POWER LED

on the device is green and the STATUS LED turns off, then click Refresh List.

If the device does not appear, try the following:

• If you connected your device directly to your computer, ensure your network

card is configured to obtain an IP address automatically, then click Refresh

List.

• If you plugged your device into an Ethernet port that is not on your subnet, try

using its hostname. If your DHCP server is set up to automatically register

hostnames, the device registers the hostname as WLS-<serial number> or

ENET-<serial number>. Enter the hostname into the Add Device

Manually field, and click the +button.

• If you know the device IP address, such as 192.168.0.2, enter it into the

Add Device Manually field, and click the +button.

For additional troubleshooting resources for the NI WLS/ENET-9163, refer

to the KnowledgeBase document, Troubleshooting Resources for the

NI WLS/ENET-9163, by going to ni.com/info and entering the info code 9163.

If your device still does not appear, contact your system administrator to confirm

that the network is working and that a firewall is not interfering with discovery.

For more information about the ports used for discovery and communication, refer

to the NI WLS/ENET-9163 User Guide and Specifications.

Troubleshooting Device Connectivity

If your device becomes disconnected from the network, try the following:

• After moving the device to a new network, NI-DAQmx may lose connection

to the device. In this case, click Reconnect to provide NI-DAQmx with the

new hostname or IP address. For more information about connecting to

network devices, refer to the NI WLS/ENET-9163 User Guide and

Specifications.

• The NI WLS/ENET-9000 Series device icon indicates whether it is recognized

and present on the network. If a connected device appears as disconnected in

the configuration tree in MAX, , press <F5> to reconnect. If successful,

the device icon changes, .

NI-DAQmx for NI WLS/ENET-9163 Getting Started Guide 8 ni.com

For additional troubleshooting resources for the NI WLS/ENET-9163, refer

to the KnowledgeBase document, Troubleshooting Resources for the

NI WLS/ENET-9163, by going to ni.com/info and entering the info code 9163.

Step 4. Configure the Device

Select your device under Network Devices to open the Network Config tab.

The Network Config tab contains the following fields:

•Device Information—NI-DAQmx populates these fields when the device is

added to your system.

•General Network Settings—Enter the following information in the General

Network Settings section:

– Hostname—The default is WLS-<serial number> or

ENET-<serial number>. This field is limited to 32 characters.

– Comment—Use this field to enter notes, such as the device location.

•(NI WLS-9000 Series Only) Wireless Configuration—To configure your

NI WLS-9000 Series device for connection to the wireless network, select

the Wireless Configuration tab and complete the following steps.

a. Select the country in which the device is operating from the Country

pull-down menu.

b. (Optional) Click the Radio On checkbox to enable the radio. Selecting

Radio On populates the Wireless Configuration tab with additional fields.

• Select DHCP + Link-Local, DHCP, Static, or Link-Local from the

Obtain IP Address Through pull-down menu.

If you selected DHCP from the Obtain IP Address Through pull-down

menu, the IP Address, Subnet Mask, Gateway, DNS Server fields are

automatically populated after you save your settings. Otherwise, ask

your network administrator for the correct settings.

• Select or enter the name of the wireless network to which you want to

connect in the SSID (Service Set Identifier) field.

• Select Infrastructure or Ad Hoc from the Wireless Mode pull-down

menu.

NI-DAQmx for NI WLS/ENET-9163 Getting Started Guide 10 ni.com

• Select the type of authentication (Open, WEP, WPA Pre-Shared

Key, WPA2 Pre-Shared Key, WPA Enterprise, WPA2

Enterprise) used on the wireless network from the Authentication

Type pull-down menu. Contact your network administrator for the

appropriate settings. For more information about the resulting fields,

refer to the NI-DAQmx Help, accessible from Start»All Programs»

National Instruments»NI-DAQ.

• Select LEAP, PEAP, TTLS, or TLS from the EAP Type pull-down

menu.

If you selected LEAP or PEAP from the EAP Type pull-down menu,

the you must enter the correct login and password in the Username

and Password fields. Ask your network administrator for the correct

settings.

c. Click Save Settings. The Apply Changes? alert opens. Click OK.

The WLS LINK LED lights on the device indicating a connected and

authenticated network link.

d. If Link Status (Wireless) in the Device Information section of the Network

Config tab is listed as Down, click the Refresh button a few times. Link

Status (Wireless) must be listed as Up before you can disconnect the

Ethernet cable.

When the device is properly configured, you can connect the device to the

wireless network that you configured it for by disconnecting the Ethernet

cable from the device and clicking the Refresh button so that the Link Status

(Wired) changes to Down. For more information about MAX configuration,

refer to the NI-DAQmx Help, accessible from Start»All Programs»National

Instruments»NI-DAQ.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de National Instruments

National Instruments

National Instruments NI 9871 Manual de usuario

National Instruments

National Instruments NI 9751 Manual de usuario

National Instruments

National Instruments NI 9234 Manual de usuario

National Instruments

National Instruments 9759 Manual de usuario

National Instruments

National Instruments SET-1415 Manual de lista de piezas

National Instruments

National Instruments PXI-6683 Series Manual de usuario

National Instruments

National Instruments NI 9246 Manual de usuario

National Instruments

National Instruments NI 9436 Manual de usuario

National Instruments

National Instruments SCXI-1181K Manual de usuario

National Instruments

National Instruments SCXI SCXI-1102 Instrucciones de instalación y funcionamiento

National Instruments

National Instruments PXIe-6591R Manual de usuario

National Instruments

National Instruments REM-11178 Manual de usuario

National Instruments

National Instruments ISM-7400 Manual de usuario

National Instruments

National Instruments NI 9201 Manual de usuario

National Instruments

National Instruments NI 9503 C Series Manual de usuario

National Instruments

National Instruments 9503 Manual de usuario

National Instruments

National Instruments PXIe-4357 Manual

National Instruments

National Instruments NI 9214 Manual de usuario

National Instruments

National Instruments SCXI-1160 Manual de usuario

National Instruments

National Instruments NI 6013 Guía de inicio rápido

National Instruments

National Instruments NI TB-4300B Manual

National Instruments

National Instruments 5761R Manual de usuario

National Instruments

National Instruments NI 9219 Manual

National Instruments

National Instruments NI 9247 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario