National Instruments NI 9218 Manual de usuario

(217) 352-9330 | [email protected] | artisantg.com

ARTISAN

TECHNOLOGY

GROUP

Your definitive source

for

quality

pre-owned

equipment.

Artisan Technology

Group

Full-service,

independent

repair

center

with

experienced

engineers

and

technicians

on staff.

buy

your

excess,

underutilized,

and

idle

equipment

along

with

credit

for

buybacks

and

trade-ins

Custom

engineering

your

equipment

works

exactly as

you

specify.

•

Critical

and

expedited

services

•

Leasing

Rentals/

Demos

• In

stock/

Ready-to-ship

•

!TAR-certified

secure

asset

solutions

Expert

team

ITrust

guarantee

100%

satisfaction

All

ademarks,

names, a

s a

earing here

are

e property of

pecti

ner

Find the National Instruments NI 9218 at our website: Click HERE

GETTING STARTED GUIDE

NI 9218

2 AI, 51.2 kS/s/ch Simultaneous, Universal

Measurements

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

This document explains how to connect to the NI 9218. In this

document, the NI 9218 with LEMO and the NI 9218 with DSUB

are referred to inclusively as the NI 9218.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9218. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9218 only as described in this document.

Caution Do not operate the NI 9218 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

2| ni.com | NI 9218 Getting Started Guide

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

way. If the product is damaged, return it to NI for

repair.

NI 9218 with LEMO Safety Voltages

Connect only voltages that are within the following limits:

Maximum voltage,

from any pin to any pin

on a single connector1

±30 V

Isolation

Channel-to-channel, channel-to-Vsup, channel-to-earth,

Vsup-to-earth (up to 5,000 m)2

Continuous 60 VDC, Measurement

Category I

Withstand 1,000 Vrms, verified by a 5 s

dielectric withstand test

1The maximum voltage between pin 2 and pin 3 on a single connector is -20 V to

+30 V.

2Must use crimp contact LEMO plug (784162-01) to maintain these ratings.

Ratings are invalidated if solder version is used.

NI 9218 Getting Started Guide | © National Instruments | 3

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Caution Any excitation output voltage to earth ground

must remain below 60 VDC for each channel. To

determine excitation output voltage to earth ground for

a channel, add the maximum excitation voltage to the

maximum potential on pin 3. The maximum excitation

voltages are 2 V +3% and 3.3 V +3% for the bridge

excitations, 12 V +5% for the +12 V excitation, and

22 V for the IEPE excitation.

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Caution Do not connect the NI 9218 to signals or use

for measurements within Measurement Categories II,

III, or IV.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are not

4| ni.com | NI 9218 Getting Started Guide

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

intended for direct connection to the MAINS building

installations of Measurement Categories CAT II,

CAT III, or CAT IV.

NI 9218 with DSUB Safety Voltages

Connect only voltages that are within the following limits:

Maximum voltage,

from any pin to any pin

on a single connector3

±30 V

Isolation

Channel-to-channel, channel-to-Vsup inputs (up to 5,000 m)

Continuous 60 VDC, Measurement

Category I

Withstand 1,000 Vrms, verified by a 5 s

dielectric withstand test

3The maximum voltage between pin 2 and pin 3 on a single connector is -20 V to

+30 V.

NI 9218 Getting Started Guide | © National Instruments | 5

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Channel-to-earth ground (up to 3,000 m)

Continuous 60 VDC, Measurement

Category I

Withstand 1,000 Vrms, verified by a 5 s

dielectric withstand test

Channel-to-earth ground (up to 5,000 m)

Continuous 60 VDC, Measurement

Category I

Withstand 860 Vrms

Vsup inputs-to-earth ground (up to 5,000 m)

Continuous 60 VDC, Measurement

Category I

Withstand 1,000 Vrms, verified by a 5 s

dielectric withstand test

Caution Any excitation output voltage to earth ground

must remain below 60 VDC for each channel. To

determine excitation output voltage to earth ground for

a channel, add the maximum excitation voltage to the

maximum potential on pin 3. The maximum excitation

6| ni.com | NI 9218 Getting Started Guide

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

voltages are 2 V +3% and 3.3 V +3% for the bridge

excitations, 12 V +5% for the +12 V excitation, and

22 V for the IEPE excitation.

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Caution Do not connect the NI 9218 to signals or use

for measurements within Measurement Categories II,

III, or IV.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are not

intended for direct connection to the MAINS building

installations of Measurement Categories CAT II,

CAT III, or CAT IV.

NI 9218 Getting Started Guide | © National Instruments | 7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Safety Guidelines for Hazardous Locations

The NI 9218 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9218 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

8| ni.com | NI 9218 Getting Started Guide

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9218 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 12 ATEX 1202658X and is

IECEx UL 14.0089X certified. Each NI 9218 is marked II 3G

and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9218

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

NI 9218 Getting Started Guide | © National Instruments | 9

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Otros manuales para NI 9218

Tabla de contenidos

Otros manuales de Unidad de control de National Instruments

National Instruments

National Instruments FieldPoint FP-2000 Manual de usuario

National Instruments

National Instruments NI 9760 Manual de usuario

National Instruments

National Instruments PXIe-4322 Manual de usuario

National Instruments

National Instruments CompactRIO cRIO-FRC Manual de usuario

National Instruments

National Instruments NI 9221 Manual de usuario

National Instruments

National Instruments SCXI-1530 Manual de usuario

National Instruments

National Instruments C Series Manual de usuario

National Instruments

National Instruments PXIe-4357 Manual

National Instruments

National Instruments 6587 Manual de usuario

National Instruments

National Instruments FieldPoint FP-1300 Manual de usuario

National Instruments

National Instruments NI 9215 Manual

National Instruments

National Instruments NI 9478 Manual de usuario

National Instruments

National Instruments NI 9234 Manual de usuario

National Instruments

National Instruments PCIe-7858 Manual de usuario

National Instruments

National Instruments ELVIS RIO CM Manual de usuario

National Instruments

National Instruments Module SCXI-1125 Manual de usuario

National Instruments

National Instruments NI 9235 Manual de usuario

National Instruments

National Instruments NI 9472 Manual de usuario

National Instruments

National Instruments NI-5783 Manual de usuario

National Instruments

National Instruments SCXI-1000 Manual de usuario

National Instruments

National Instruments SCXI-1160 Manual de usuario

National Instruments

National Instruments NI 9246 Manual de usuario

National Instruments

National Instruments NI 9503 C Series Manual de usuario

National Instruments

National Instruments NI-9477 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario