National Instruments NI-9146 Manual del propietario
NI-9146
Safety,
Environmental,
and
Regulatory
Information
2022-07-20
Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
NI 9146 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ni.com
2
NI-9146 Safety, Environmental, and Regulatory Information
Overview
This document describes how to connect the NI 9146 to a network and how to use
the NI 9146 features. This document also contains specifications for the NI 9146.
Figure 1. NI 9146 Front Panel
C
V
NI 9146
INPUT
9-30 V
15 W MAX
M
N
S
AN
NI TIO
RT UTS
LA
EN
ACT/
LINK
10/100
1
2
3
RESET
4
STATUS
USER FPGA1
POWER
1. LEDs
2. RJ-45 Ethernet Port
3. Power Connector
4. Reset Button
Safety Guidelines
Operate the NI 9146 only as described in this document.
Caution Do not operate the NI 9146 in a manner not specified in this
document. Product misuse can result in a hazard. You can compromise the
safety protection built into the product if the product is damaged in any
way. If the product is damaged, return it to NI for repair.
© National Instruments 3
NI-9146 Safety, Environmental, and Regulatory Information
Safety Guidelines for Hazardous Locations
The NI 9146 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous
locations; Class I, Zone 2, AEx nA IIC T4 and Ex nA IIC T4 hazardous locations;
and nonhazardous locations only. Follow these guidelines if you are installing the
NI 9146 in a potentially explosive environment. Not following these guidelines may
result in serious injury or death.
Caution Do not disconnect the power supply wires and connectors from
the controller unless power has been switched o.
Caution Do not disconnect I/O-side wires or connectors unless power
has been switched o or the area is known to be nonhazardous.
Caution Do not remove modules unless power has been switched o or
the area is known to be nonhazardous.
Caution Substitution of components may impair suitability for Class I,
Division 2.
Caution For Division 2 and Zone 2 applications, install the system in an
enclosure rated to at least IP54 as defined by IEC/EN 60079-15.
Special Conditions for Hazardous Locations Use in Europe and
Internationally
The NI 9146 has been evaluated as Ex nA IIC T4 Gc equipment under DEMKO
Certificate No. 07 ATEX 0626664X and is IECEx UL 14.0089X certified. Each device is
marked II 3G and is suitable for use in Zone 2 hazardous locations, in ambient
temperatures of -40 °C ≤ Ta ≤ 70 °C.
ni.com
4
NI-9146 Safety, Environmental, and Regulatory Information
Caution You must make sure that transient disturbances do not exceed
140% of the rated voltage.
Caution The system shall only be used in an area of not more than
Pollution Degree 2, as defined in IEC 60664-1.
Caution The system shall be mounted in an ATEX/IECEx-certified
enclosure with a minimum ingress protection rating of at least IP54 as
defined in IEC/EN 60079-15.
Caution The enclosure must have a door or cover accessible only by the
use of a tool.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits
for electromagnetic compatibility (EMC) stated in the product specifications. These
requirements and limits provide reasonable protection against harmful interference
when the product is operated in the intended operational electromagnetic
environment.
This product is intended for use in industrial locations. However, harmful
interference may occur in some installations, when the product is connected to
a peripheral device or test object, or if the product is used in residential or
commercial areas. To minimize interference with radio and television reception and
prevent unacceptable performance degradation, install and use this product in strict
accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved
by National Instruments could void your authority to operate it under your local
regulatory rules.
© National Instruments 5
NI-9146 Safety, Environmental, and Regulatory Information
Special Conditions for Marine Applications
Some products are Lloyd’s Register (LR) Type Approved for marine (shipboard)
applications. To verify Lloyd’s Register certification for a product, visit ni.com/
certification and search for the LR certificate, or look for the Lloyd’s Register mark
on the product.
Caution In order to meet the EMC requirements for marine applications,
install the product in a shielded enclosure with shielded and/or filtered
power and input/output ports. In addition, take precautions when
designing, selecting, and installing measurement probes and cables to
ensure that the desired EMC performance is attained.
Unpacking the Kit
Caution To prevent electrostatic discharge (ESD) from damaging the
device, ground yourself using a grounding strap or by holding a grounded
object, such as your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the device from the package and inspect the device for loose
components or any other sign of damage.
Caution Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the device in the antistatic package when the device is not in use.
ni.com
6
NI-9146 Safety, Environmental, and Regulatory Information
What You Need to Install the NI 9146
■NI 9146 Ethernet Expansion Chassis
■NI-RIO Soware DVD
■C Series I/O modules
■DIN rail mount kit (for DIN rail mounting only)
■Panel mount kit (for panel mounting only)
■Two M4 or number 8 flathead screws (for mounting the chassis without one
of the listed mounting kits)
■A number 2 Phillips screwdriver
■Power supply
■Ethernet cable
Note Visit ni.com/info and enter the Info Code rdsowareversion to
determine which soware you need to use the NI 9146.
Mounting the Chassis
You can mount the chassis horizontally on a flat, vertical, metallic surface such as
a panel or wall. The maximum allowable ambient temperature for operation in this
configuration is 70 °C. The following figure shows the chassis mounted horizontally.
Figure 2. NI 9146 Mounted Horizontally
C
V
RESET
NI 9146
INPUT
9-30 V
15 W MAX
M
N
S
AN
NI TIO
RT UT
LA
EN S
ACT/
LINK
10/100
Up
STATUS
USER FPGA1
POWER
You can also mount the chassis on a panel or wall in other orientations, on a non-
metallic surface, on a 35 mm DIN rail, on a rack, in an enclosure, or on a desktop.
Mounting the chassis in these or other configurations can reduce the maximum
allowable ambient temperature and can aect the typical accuracy of modules in
the chassis.
© National Instruments 7
NI-9146 Safety, Environmental, and Regulatory Information
Note For information about how dierent mounting configurations can
cause
temperature derating, go to ni.com/info and enter the Info Code
criomounting.
Note For information about typical accuracy specifications for modules,
go to ni.com/info and enter the Info Code criotypical.
Your installation must meet the following requirements for space and cabling
clearance:
■Allow 25.4 mm (1 in.) on the top and the bottom of the chassis for air
circulation.
■Allow 50.8 mm (2 in.) in front of modules for cabling clearance.
Figure 3. NI 9146 Bottom View with Dimensions
4 mm
(0.16 in.)
178.1 mm
(7.01 in.)
29.1 mm
(1.14 in.)
64.3mm
(2.53in.)
48.4 mm
(1.91 in.)
2
25.4 mm
(1 in.)
63.5 mm
(2.50 in.)
1
63.5 mm
(2.50 in.)
1
25.4 mm
(1 in.)
1. Measure ambient temperature here.
2. Chassis Grounding Screw
ni.com
8
NI-9146 Safety, Environmental, and Regulatory Information
Figure 4. NI 9146 Front View with Dimensions
C
V
RESET
NI 9146
INPUT
9-30 V
15 W MAX
M
N
S
AN
NI TIO
RT UT
LA
EN S
ACT/
LINK
10/100
87.3mm
(3.44 in.)
41.1 mm
(1.62 in.)
47.0 mm
(1.85 in.)
47.2 mm
(1.86 in.)
30.6 mm
(1.2 in.)
Cooling Outline 25.4 mm (1 in.)
Cooling Outline 25.4 mm (1 in.)
STATUS
USER FPGA1
POWER
Figure 5. NI 9146 Side View with Dimensions
]
2X M4X0.7
44.0 mm
(1.73 in.)
74.0 mm
(2.91 in.)
29.1 mm
(1.15 in.)
44.1 mm
(1.54 in.)
The following sections give instructions for the mounting methods. Before using any
of these mounting methods, record the serial number from the back of the chassis.
You will be unable to read the serial number aer you have mounted the chassis.
Caution Make sure that no I/O modules are in the chassis before
mounting it.
Mounting the Chassis on a Panel
You can use the NI 9904 panel mount kit to mount the NI 9146 on a flat surface.
Complete the following steps to mount the NI 9146 on a panel.
1. Fasten the chassis to the panel mount kit using a number 2 Phillips
screwdriver and two M4 × 25 screws. National Instruments provides these
© National Instruments 9
NI-9146 Safety, Environmental, and Regulatory Information
screws with the panel mount kit. You must use these screws because they are
the correct depth and thread for the panel. Tighten the screws to a maximum
torque of 1.3 N · m (11.5 lb · in.).
Figure 6. Installing the Panel Mount Accessory on the NI 9146
Figure 7. Dimensions of NI 9146 with Panel Mount Accessory Installed
C
V
RESET
NI 9146
INPUT
9-30 V
15 W MAX
M
N
S
AN
NI TIO
RT UT
LA
EN S
ACT/
LINK
10/100
29.5 mm
(1.16 in.)
9.5 mm
(0.38 in.)
27.3mm
(1.08 in.)
215.9 mm
(8.5 in.)
235.0 mm
(9.25 in.)
31.7 mm
(1.25 in.) 63.5 mm
(2.50 in.)
88.1 mm
(3.47 in.)
7.2 mm
(0.29 in.)
STATUS
USER FPGA1
POWER
2. Fasten the NI 9904 panel to the wall using the screwdriver and screws that are
appropriate for the wall surface. The maximum screw size is M4 or number 8.
Caution Make sure that no I/O modules are in the chassis before
removing it from the panel.
ni.com
10
NI-9146 Safety, Environmental, and Regulatory Information
Tabla de contenidos
Otros manuales de Hardware de computadora de National Instruments
National Instruments
National Instruments NI-9260 Manual de usuario
National Instruments
National Instruments NI PXIe-8105 Manual de usuario
National Instruments
National Instruments Compact FieldPoint Mounting Accessories... Manual de usuario
National Instruments
National Instruments PXI-8335 Manual de usuario
National Instruments
National Instruments GPIB Series Manual de usuario
National Instruments
National Instruments AT-GPIB/TNT Manual de usuario
National Instruments
National Instruments NI-488.2M Manual de usuario
National Instruments
National Instruments GPIB-PCIIB Manual de usuario
National Instruments
National Instruments NI 9213 Manual de usuario
National Instruments
National Instruments NI PXI-8221 Manual de usuario
National Instruments
National Instruments PXIe-7911 Manual de usuario
National Instruments
National Instruments NI PXIe-1085 Manual de usuario
National Instruments
National Instruments DAQ X NI 634 Series Manual de usuario
National Instruments
National Instruments NI-9238 Manual de usuario
National Instruments
National Instruments PXI Manual de usuario
National Instruments
National Instruments MXI-2 Manual de usuario
National Instruments
National Instruments SC Express PXIe-4331 Manual de usuario
National Instruments
National Instruments 8330 Series Manual de usuario
National Instruments
National Instruments SET-2090 Manual de lista de piezas
National Instruments
National Instruments NI 9219 Manual de usuario
National Instruments
National Instruments NI PXIe-1062Q Manual de usuario
National Instruments
National Instruments NI PXIe-8133 Manual de usuario
National Instruments
National Instruments Deterministic Ethernet Expansion Chassis NI... Manual de usuario
National Instruments
National Instruments PC-LPM-16/PnP Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
Hauppauge
Hauppauge WinTV-HVR-2250 Manual de usuario
