National Instruments PXIe-7911 Manual de usuario
PXIe-7911/7912/7915
Getting Started
2022-07-06
Contents
Getting Started Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FlexRIO Documentation and Resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Verifying the System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking the Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PXIe-7911/7912/7915 Kit Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the Application Soware and Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the PXIe-7911/7912/7915. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PXIe-7911/7912/7915 Front Panels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Configuring the PXIe-7911/7912/7915 in MAX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
FlexRIO Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessing FlexRIO Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Making a Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Making a Measurement with LabVIEW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
What Should I Do if the PXIe-7911/7912/7915 Does Not Appear in MAX?. . . . . 14
What Should I Do if the PXIe-7911/7912/7915 Fails the Self-Test?. . . . . . . . . . . . 15
NI Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ni.com
2
PXIe-7911/7912/7915 Getting Started
Getting Started Guide
Note Before you begin, install and configure your chassis and controller.
This document explains how to install, configure, test, and use the
PXIe-7911/7912/7915. You can program the PXIe-7911/7912/7915 with the following
soware options.
■FlexRIO Support driver soware
■NI LabVIEW Instrument Design Libraries for FlexRIO (instrument design
libraries)
Safety Guidelines
Caution You can impair the protection provided by the
PXIe-7911/7912/7915 if you use it in a manner not described in this
document.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits
for electromagnetic compatibility (EMC) stated in the product specifications. These
requirements and limits provide reasonable protection against harmful interference
when the product is operated in the intended operational electromagnetic
environment.
This product is intended for use in industrial locations. However, harmful
interference may occur in some installations, when the product is connected to a
peripheral device or test object, or if the product is used in residential or
commercial areas. To minimize interference with radio and television reception and
prevent unacceptable performance degradation, install and use this product in strict
accordance with the instructions in the product documentation.
© National Instruments 3
PXIe-7911/7912/7915 Getting Started
Furthermore, any changes or modifications to the product not expressly approved
by NI could void your authority to operate it under your local regulatory rules.
FlexRIO Documentation and Resources
Document/Resource Location Description
PXIe-7911/7912/7915
Getting Started Guide (this
document)
Available at ni.com/
manuals.
Contains installation instructions and
basic programming instructions for your
PXIe-7911/7912/7915.
PXI-7911 Specifications,
PXI-7912 Specifications,
PXI-7915 Specifications
Available at ni.com/
manuals.
Contains specifications for your
PXIe-7911/7912/7915.
PXIe-7911/7912/7915 Safety,
Environmental, and
Regulatory Information
Available at ni.com/
manuals.
Contains important safety,
environmental, and regulatory
information for your
PXIe-7911/7912/7915.
LabVIEW FPGA Module Help Embedded in LabVIEW
Help and at ni.com/
manuals.
Contains information about the basic
functionality of the LabVIEW FPGA
Module.
FlexRIO Help Available at ni.com/
manuals.
Contains information about the FPGA
module front panel connectors and I/O,
programming instructions, and I/O
component-level IP (CLIP).
LabVIEW Examples Available in NI Example
Finder. In LabVIEW,
click Help » Find
Examples » Hardware
Input and Output »
FlexRIO.
Contains examples of how to run FPGA
VIs and Host VIs on your FlexRIO devices.
FlexRIO product page Located at ni.com/
flexrio.
Contains product information and data
sheets for FlexRIO hardware.
Table 1. FlexRIO Documentation and Resources
Verifying the System Requirements
To use the PXIe-7911/7912/7915, your system must meet certain requirements. For
more information about minimum system requirements, recommended system,
ni.com
4
PXIe-7911/7912/7915 Getting Started
and supported application development environments (ADEs), refer to the readme,
which is installed or available at ni.com/manuals.
Unpacking the Kit
Notice To prevent electrostatic discharge (ESD) from damaging the
device, ground yourself using a grounding strap or by holding a grounded
object, such as your computer chassis.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the device from the package and inspect the device for loose
components or any other sign of damage.
Notice Never touch the exposed pins of connectors.
Note Do not install a device if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the device in the antistatic package when the device is not in use.
PXIe-7911/7912/7915 Kit Contents
The following items are included in the device kit:
■PXIe-7911/7912/7915
■Documentation:
■PXIe-7911/7912/7915 Getting Started Guide (this document)
■PXIe-7911/7912/7915 Safety, Environmental, and Regulatory
Information
© National Instruments 5
PXIe-7911/7912/7915 Getting Started
Preparing the Environment
Ensure the environment in which you are using the PXIe-7911/7912/7915 meets the
following specifications.
Operating environment
Ambient temperature
range
0 °C to 45 °C (Tested in accordance with IEC-60068-2-1 and
IEC-60068-2-2. Meets MIL-PRF-28800FClass 3 low temperature limit
and MIL-PRF-28800FClass 4 high temperature limit.)
Relative humidity range 10% to 90%, noncondensing
Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient temperature)
Pollution Degree 2
Indoor use only.
Note For complete specifications, refer to the specifications document for
your device at ni.com/manuals.
Installing the Application Soware and Driver
Before installing your hardware, you must install the application soware and
instrument driver. Visit NI FlexRIO Driver Supported Versions for FlexRIO Adapters
and Modules to determine which minimum soware versions you need for your
device. Install the soware in the following order:
1. Install LabVIEW.
Refer to the LabVIEW Installation Guide for installation instructions for
LabVIEW and system requirements for the LabVIEW soware. Refer to the
LabVIEW Upgrade Notes for additional information about upgrading to the
most recent version of LabVIEW for Windows. Documentation for LabVIEW is
available at ni.com/manuals and by selecting Start » All Programs » National
Instruments » LabVIEW » LabVIEW Manuals.
2. Install the LabVIEW FPGA Module.
ni.com
6
PXIe-7911/7912/7915 Getting Started
Refer to the LabVIEW FPGA Module Release and Upgrade Notes for
installation instructions and information about getting started with the
LabVIEW FPGA Module. Documentation for the LabVIEW FPGA Module is
available at ni.com/manuals and by selecting Start » All Programs » National
Instruments » LabVIEW » LabVIEW Manuals.
3. Install FlexRIO Support.
Refer to the FlexRIO Readme on the FlexRIO installation media for system
requirements and installation instructions for FlexRIO Support.
Documentation for FlexRIO Support is available at ni.com/manuals and by
selecting Start » All Programs » National Instruments » NI FlexRIO.
Installing the PXIe-7911/7912/7915
Notice To prevent damage to the PXIe-7911/7912/7915 caused by ESD or
contamination, handle the module using the edges or the metal bracket.
1. Ensure the AC power source is connected to the chassis before installing the
module.
The AC power cord grounds the chassis and protects it from electrical damage
while you install the module.
2. Power o the chassis.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior
to installation. Do not install a module if the backplane is damaged.
4. Remove the black plastic covers from all the captive screws on the module
front panel.
5. Identify a supported slot in the chassis. The following figure shows the
symbols that indicate the slot types.
© National Instruments 7
PXIe-7911/7912/7915 Getting Started
Figure 1. Chassis Compatibility Symbols
12 3 45
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
6. Touch any metal part of the chassis to discharge static electricity.
7. Ensure that the ejector handle is in the downward (unlatched) position.
8. Place the module edges into the module guides at the top and bottom of the
chassis. Slide the module into the slot until it is fully inserted.
9. Latch the module in place by pulling up on the ejector handle.
10. Secure the module front panel to the chassis using the front-panel mounting
screws.
Note Tightening the top and bottom mounting screws increases
mechanical stability and also electrically connects the front panel to
the chassis, which can improve the signal quality and
electromagnetic performance.
11. Cover all empty slots using either filler panels (standard or EMC) or slot
blockers with filler panels, depending on your application.
Note For more information about installing slot blockers and filler
panels, go to ni.com/r/pxiblocker.
12. Power on the chassis.
ni.com
8
PXIe-7911/7912/7915 Getting Started
PXIe-7911/7912/7915 Front Panels
The following figures show the PXIe-7911/7912/7915 front panels.
Figure 2. PXIe-7911 Front Panel
PXIe-7911
FlexRIO Coprocessor
Kintex UltraScale
KU035 FPGA
© National Instruments 9
PXIe-7911/7912/7915 Getting Started
Figure 3. PXIe-7912 Front Panel
PXIe-7912
FlexRIO Coprocessor
DIO
Kintex UltraScale
KU040 FPGA
4 GB
DRAM
The following table describes the signal connections for the PXIe-7912.
Connector Description Function
DIO Molex™ Nano-Pitch DIO
connector
Multi-signal DIO connector that provides access to FPGA
multi-gigabit transceivers (MGTs) and general-purpose
LVCMOS signals.
The following table lists the available pins on the DIO connector.
Signal Type Description
MGT Tx± <3..0> Xilinx UltraScale GTH Output
MGT Rx± <3..0> Xilinx UltraScale GTH Input
DIO <7..0> Single-ended Bidirectional
5.0 V DC Output
ni.com
10
PXIe-7911/7912/7915 Getting Started
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Hardware de computadora de National Instruments
National Instruments
National Instruments GPIB-1014 Series Manual de usuario
National Instruments
National Instruments NI-9238 Manual de usuario
National Instruments
National Instruments GPIB Series Manual de usuario
National Instruments
National Instruments NI PXIe-8130 Manual de usuario
National Instruments
National Instruments PXI-8335 Manual de usuario
National Instruments
National Instruments NI PXIe-8130 Manual de usuario
National Instruments
National Instruments PXI Express NI PXIe-1065 Manual de usuario
National Instruments
National Instruments DAQPad-6020E Manual de usuario
National Instruments
National Instruments Isolated Analog Output Module SCC-AO10 Manual de usuario
National Instruments
National Instruments IMAQTM Manual de usuario
National Instruments
National Instruments PXI NI 8171 Series Manual de usuario
National Instruments
National Instruments sbRIO-9607 Manual de usuario
National Instruments
National Instruments NI PXIe-8105 Manual de usuario
National Instruments
National Instruments PXI-8101 Manual de usuario
National Instruments
National Instruments MXI Express x4 Manual de usuario
National Instruments
National Instruments NI 9213 Manual de usuario
National Instruments
National Instruments 9260 Manual de usuario
National Instruments
National Instruments USB-7856 Manual de usuario
National Instruments
National Instruments NI PXIe-1082 Manual de usuario
National Instruments
National Instruments PXIe-5832 Manual de usuario
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
Hauppauge
Hauppauge WinTV-HVR-2250 Manual de usuario
