Moxa Technologies ToughNet TN-5516 Series Manual

Reproduction without permission is prohibited.

P/N: 1802055160013

TN-5516/5518 Series

Hardware Installation Guide

Moxa ToughNet Switch

Fourth Edition, November 2010

nsole and relay output.

/VAC (88 to 300 VDC, 85 to 264 VAC),

e Protocol) for the precise time

nt with different policies.

•Turbo Ring, Turbo Chain,and RSTP/STP (IEEE802.1w/D).

Overview

The ToughNet TN-5516/5518 series M12 managed Ethernet switches are

designed for industrial applications in harsh environments. The TN series

switches use M12 connectors to ensure tight, robust connections, and

guarantee reliable operation against environmental disturbances, such as

vibration and shock. The wide selection of 12/24/36/48 VDC, 72/96/110

VDC, or 110/220 VDC/VAC dual redundant power supplies increases the

reliability of your communications. The TN-5516 switches provide up to

16 fast Ethernet M12 ports.

The TN-5518 switches provide up to 16 fast Ethernet M12 ports, and the

2 ports located on the bottom provide a Gigabit Ethernet interface with

bypass relay option. Models with an extended operating temperature

range of -40 to 75°C are also available. The TN-5516/5518 series

Ethernet switches are compliant with EN50155/50121-3-2/50121-4

(railway applications), NEMA TS2 (traffic control systems), and e-Mark

(vehicles) requirements, making the switches suitable for a variety o

industrial applications.

Package Checklist

Your ToughNet TN-5516/5518 switch is shipped with the following items.

If any of these items is missing or damaged, please contact your

customer service representative for assistance.

•1 Moxa ToughNet switch.

•Hardware installation guide.

•CD-ROM with user’s manual, Windows utility, and SNMP MIB file

•Moxa product warranty statement

•M12 to DB9 console port cable.

r console and relay output port•2 protective caps fo

•Panel mounting kit.

Features

Anti-Vibration Circular Connectors for Robust Links

•M12 D-coding 4-pin female connectors for Fast Ethernet

10/100BaseT(X) ports.

•M12 connectors for Gigabit Ethernet 10/100/1000BaseT(X) ports

•M12 A-coding 5-pin male connectors for co

•M23 6-pin male connector for power input

Dual, Isolated Redundant Power Inputs

•Supports 12/24/36/48 VDC (8.4 to 60 VDC).

•Supports 72/110 VDC (50.4 to 54 VDC), isolated.

•Supports 110/220 VDC

isolated.

•Dual redundant, parallel load-sharing power supplie

High Performance Network Switching Technolog

•IPv6 ready, certified by the IPv6 Logo Committee.

•IEEE 1588 PTP (Precision Tim

synchronization of networks.

•DHCP Option 82 for IP address assignme

•Modbus/TCP industrial Ethernet protocol.

- 2 -

•IGMP Snooping and GMRP for filtering multicast traffic from industria

Ethernet protocols. l

stallable M12 D-coded screw-in connector,

llable M12 A-coded screw-in connector,

DK-DC50131: DIN-Rail mounting kit, 50 x 131 mm.

•Port-based VLAN, IEEE802.1Q VLAN, and GVRP protocol to ease

network planning.

•QoS (IEEE802.1p/1Q and TOS/DiffServ) to increase determinism

•802.3ad, LACP for optimum bandwidth utilization.

•IEEE802.1X and https/SSL to enhance network security.

•SNMP v1/v2c/v3 for different levels of network management.

•RMON for efficient network monitoring and proactive capability

•Bandwidth management prevents unpredictable network status

•Lock port allows access by only authorized MAC addresses

•Port mirroring for online debugging.

•Automatic warning by exception through email, relay output

•Automatic recovery of connected devices’ IP addresses.

•Line-swap fast recovery.

•LLDP for automatic topology discovery through network managemen

software.

•Configurable through Web browser, Telnet/Serial console, and

Windows utility.

Designed for Industry-specific Applications

•Two Gigabit Ethernet ports to meet high bandwidth requirements.

•Bypass relay option on the 2 Gigabit Ethernet ports ensure non-stop

data communication in the event the switch stops working due to a

power failure .

•Three rotary switches for setting the last 3 digits of the IP address

makes maintenance even easier. a•EN 50155/50121-3-2/50121-4, NEMA TS2, and e-Mark compli

•e (for “-T” models). nt

-40 to 75°C operating temperature rang

•IP54/IP67, rugged high-strength case.

•Panel mounting or DIN-Rail mounting installation capability.

Recommended Optional Accessories

•CBL-M23(FF6P)Open-BK-100-IP67: 1-meter M23 to 6-pin powe

cable with IP67-rated female 6-pin M23 connector.

•CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UT

Ethernet cable with IP67-rated male 4-pin M12 D-coded connector.

•CBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable

with IP67-rated female 5-pin M12 A-coded connector.

•M12D-4P-IP68: Field-in

male 4-pin, IP68-rated.

•M12A-5P-IP68: Field-insta

female 5-pin, IP68-rated.

•CAP-M12F-M: Metal cap for M12 female connector

•

- 3 -

TN-5516 Panel Layouts

Botton View

Rear View

8 9 10 11 12

hielded M23 connector).

for power input 2.

ad.

ler or chain tail.

aseT(X) port (female 4-pin shielded M12 connector with D

ver with Model name1. 3 Rotary switches and protective co

r panel mounting kit.2. Screw holes fo

3. Console port.

4. Grounding screw.

5. Relay output port.

6. Power input voltage range indication.

7. Power input port (male 5-pin s

8. PWR1 LED: for power input 1.

9. PWR2 LED:

10. FAULT LED.

11. MSTR/HEAD LED: for ring master or chain he

12. CPLR/TAIL LED: for ring coup

13. TP port’s 10/100 Mbps LED.

14. 10/100B

coding).

15. Waterproof vent.

E1 LED: Not used by the TN-5516 series.

16. Product label.

17. 12 Screw holes for DIN-Rail mounting kit.

18. E2: LED: Not used by the TN-5516 series

19.

- 4 -

TN-5518 Panel Layouts

ve1. 3 Rotary switches and protective co

r panel mounting kit. r with Model name.

for power input 2.

ad.

ler or chain tail.

aseT(X) port (female 4-pin shielded M12 connector with D

2. Screw holes fo

3. Console port.

4. Grounding screw.

5. Relay output port.

6. Power input voltage range indication.

hielded M23 connector).7. Power input port (male 5-pin s

8. PWR1 LED: for power input 1.

9. PWR2 LED:

10. FAULT LED.

11. MSTR/HEAD LED: for ring master or chain he

12. CPLR/TAIL LED: for ring coup

13. TP port’s 10/100 Mbps LED.

14. 10/100B

coding).

15. Waterproof vent.

- 5 -

16. Product label.

17. 12 Screw holes for DIN-Rail mounting kit. .

18. E2 LED: Down-side E2 Gigabit port's 10/100/1000 Mbps LED

19. E1 LED: Down-side E1 Gigabit port's 10/100/1000 Mbps LED

20. Gigabit Ethernet port E1 (corresponding to port 17 in the TN-5518

User's Manual).

21. Gigabit Ethernet port E2 (corresponding to port 18 in the TN-5518

User's Manual).

ATTENTION

DO NOT open or remove the vent (#15). Once the seal has bee

removed, the warranty becomes invalid. n

Exposed connectors (including 3, 5, and 14) when not in use

must be tightly covered with protective caps (an optional

accessory) to ensure IP54/IP67-rated protection.

After the rotary switches (1) are set, the protective cover must b

properly affixed to ensure IP54/IP67-rated protection

- 6 -

Mounting Dimensions (unit = mm)

TN-5516 Series

69.80

67.70

52.70

DIN-RAIL KIT

o8.00

DIN-RAIL KIT

235.00

220.00

175.80

120.00

170.00

120.00

250.00

21.00

37.00

177.00

37.00

o4.50

8.00

- 7 -

TN-5518 Series

Panel/Wall Mounting

Mounting the TN-5516/5518 to a wall requires 4 screws. Use the

Net switch as a guide to mark the correct positions of the 4 screws.

he 4 screws in the panel mounting kit. If you

ld like to use your own screws, make sure the

screw head is between 6.0 mm and 7.0 mm in

ameter and the shaft is less than 4.0 mm in

meter, as shown at the right.

ew the screws in all the way—leave a space of about 2 mm to

allow room for sliding the ToughNet switch between the wall and the

ws.

STEP

Tough

STEP

Use t

6.0 - 7.0 mm

< 4.0 mm

wou

dia

Do not scr

scre

- 8 -

NOTE Before tightening the screws into the wall, make sure the screw

head and shaft size are sui

one of the keyhole-shapedtable by inserting the screw through

apertures of the ToughNet sw

itch.

STEP 3:

Once the screws are fixed in the wall, hang the ToughNet switch on the 4

screws through the large opening of the keyhole-shaped apertures, and

then slide the switch downwards. Tighten the four screws for added

stability.

NOTE To provide greater protection from vibrations and shocks, use

screws with shaft diameter between 6.0 mm and 7.0 mm, and fix

the ToughNet switch onto the wall directly through the large

opening of the keyhole-shaped apertures.

DIN-Rail Mounting (optional)

With the optional DIN-Rail

mounting kit DK-DC50131 (must be

purchased separately), you can

mount the TN-5516/5518 on a

35mm DIN-Rail.

Use 12 screws (6 screws per plate)

STEP 1:

to atta ail

attach e rear pane

of the

ch the two DIN-R

ment plates to th l

Recessed button

switch.

Spring-loaded bracket

STEP

If the s n

to rele e

spring down a few millimeters in each

directio

pring-loaded bracket is locked in place, push the recessed butto

ase it. Once released, you should feel some resistance from th

as you slide the bracket up and

- 9 -

STEP 3:

Positio itch on then the ToughNet sw

DIN-R lamps oveail, tilting to hook c

the top

STEP 4:

Swing the switch down fully onto the

edge of the rail.

DIN-Rail, until both clamps

completely latch.

DIN-Rail

everse Step 3 and 4

To remove the Moxa ToughNet Switch from the DIN-Rail, use a

screwdriver to pull out the two spring-loaded brackets from the bottom

until they are fixed in the “locked” position. Then r

above.

DIN-Rail

Wiring Requirements

WARNING

Turn the power off before disconnecting modules or wires. The

correct power supply voltage is listed on the product label. Check

the voltage of your power source to make sure you are using the

correct voltage. Do NOT use a voltage greater than what is

specified on the product label.

These devices must be supplied by a SELV source as defined in

the Low Voltage Directive 2006/95/EC and 2004/108/EC.

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your Moxa switch.

This device has UL508 approval. Use copper conductors only,

60/75°C, and tighten to 4.5 pound-inches. For use in pollution

degree 2 environments.

- 10 -

Otros manuales para ToughNet TN-5516 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Moxa Technologies

Moxa Technologies

Moxa Technologies NPort 1220 Manual de usuario

Moxa Technologies

Moxa Technologies ThinkCore DA-660-8/16-LX Manual de usuario

Moxa Technologies

Moxa Technologies EDS-516A Series Manual de usuario

Moxa Technologies

Moxa Technologies PT-7828 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-600 Series Manual

Moxa Technologies

Moxa Technologies IKS-6728-8PoE Manual

Moxa Technologies

Moxa Technologies PT-G7728 Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G4014 Series Manual de usuario

Moxa Technologies

Moxa Technologies MDS-G4000 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-205 Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-P510 Series Manual

Moxa Technologies

Moxa Technologies EDS-316 EtherDevice Manual

Moxa Technologies

Moxa Technologies ThinkCore DA-660-8-CE Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G308 Manual

Moxa Technologies

Moxa Technologies ToughNet TN-4500A Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-4009 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-4008 Series Manual de usuario

Moxa Technologies

Moxa Technologies PT-7710 Series Manual

Moxa Technologies

Moxa Technologies NPort S8000 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-405A Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-2016-ML Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-508 Series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-2010-ML Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario