Moxa Technologies MGate 5105-MB-EIP Manual de usuario

– 1 – – 2 – – 3 –

P/N: 1802051050011

MGate 5105-MB-EIP

Quick Installation Guide

Second Edition, June 2014

Overview

The MGate 5105-MB-EIP is an industrial Ethernet gateway for

Modbus RTU/ASCII/TCP and EtherNet/IP network communication.

Package Checklist

Before installing the MGate 5105-MB-EIP, verify that the package

contains the following items:

•1 MGate 5105-MB-EIP gateway

•RJ45 to DB9 cable (for console use)

•Documentation and software CD

•Quick installation guide

•Warranty card

Optional Accessories:

•DR-45-24: 45W/2A DIN rail 24 VDC power supply with

universal 85 to 264 VAC input

•DR-75-24: 75W/3.2A DIN rail 24 VDC power supply with

universal 85 to 264 VAC input

•DR-120-24: 120W/5A DIN rail 24 VDC power supply with 88 to

132 VAC/176 to 264 VAC input by switch

•WK-36-02: Wall mounting kit

•Mini DB9F-to-TB Adaptor: DB9 female to terminal block

adapter

Please notify your sales representative if any of the above items

are missing or damaged.

Hardware Introduction

LED Indicators

LED

Color

Description

Ready

Off

Power is off or fault condition exists

Green

Steady: Power is on and the MGate is

functioning normally

Blinking: The MGate has been located by

the MGate Manager’s Location function

Red

Steady: Power is on and the MGate is

booting up

Blinking slowly: Indicates an IP conflict, or

DHCP or BOOTP server is not responding

properly

Flashing quickly: microSD card failed

EIP

(Scanner)

Off

No I/O data is exchanged

Green

Steady: I/O data is exchanged with all

devices

Blinking: I/O data is exchanged with at

least one device

(Not all configured devices can

communicate with gateway)

EIP

(Adapter)

Off

No I/O data is exchanged

Green

I/O data is exchanged with all devices

Off

No communication with Modbus device

Green

Modbus communication progress

Red

Communication error

When MGate 5105 acts as Master:

1. Slave device returned an error

(exception)

2. Received frame error

(parity error,

checksum error)

3. Timeout (slave device no

response)

When MGate 5105 acts as Slave:

1. Received invalid function code

2. Master accessed invalid register

address or coil addresses

3. Received frame error

(parity error,

checksum error)

Dimensions

Unit: mm (inch)

Reset Button

Restore the MGate to factory default settings by using a pointed

object (such as a straightened paper clip) to hold the reset button

down until the Ready LED stops blinking (approx. 5 seconds).

Pull-high, Pull-low, and Terminator for RS-485

Remove the MGate 5105-MB-EIP’s top cover and you will find DIP

switches to adjust each serial port’s pull-high resistor, pull-low

resistor, and terminator.

Pull-high

resistor

Pull-low

resistor

Terminator

1 kΩ

120 Ω

OFF

150 kΩ*

–*

*Default

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas:

+1-714-528-6777 (toll-free: 1-888-669-2872)

Europe:

+49-89-3 70 03 99-0

Asia-Pacific:

+886-2-8919-1230

China:

+86-21-5258-9955 (toll-free: 800-820-5036)

Hardware Installation Procedure

1. Connect the power adapter. Connect the 12-48 VDC power line

or DIN rail power supply to the MGate 5105-MB-EIP device’s

terminal block.

2. Use a Modbus serial cable to connect the MGate to a Modbus

slave device.

3. Use an Ethernet cable to connect the MGate to the EtherNet/IP

controller.

4. The MGate 5105-MB-EIP is designed to be attached to a

DIN rail or mounted on a wall. For DIN rail mounting, push

down the spring and properly attach it to the DIN rail until it

“snaps” into place. For wall mounting, install the wall mount kit

(optional) first, and then screw the device onto the wall. The

following figure illustrates the two mounting options:

Software Installation Information

To install MGate Manager, insert the MGate Documentation and

Software CD into your PC’s CD-ROM drive, and then run the

following setup program to begin the installation process from the

“Software” directory:

MGM_Setup_[Version]_Build_[DateTime].exe

The filename of the latest version may have the following format:

MGM_Setup_Verx.x.x_Build_xxxxxxxx.exe.

For detailed information about MGate Manager, refer to the MGate

5105-MB-EIP User's Manual, which can be found in the “Document”

directory.

Pin Assignments

Modbus Serial Port (Male DB9)

RS-232

RS-422/

RS-485 (4W)

RS-485 (2W)

DCD

TxD-(A)

–

RXD

TxD+(B)

–

TXD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

Ethernet Port (RJ45)

Signal

Tx+

Tx-

Rx+

Rx-

Power Input and Relay Output Pinouts

V2+ V2-

V1+ V1-

Shielded

Ground

Power

Input 2

Power

Input 2

N.O.

Common

N.C.

Power

Input 1

Power

Input 1

Specifications

Power Requirements

Power Input

12 to 48 VDC

Power Consumption

455 mA @ 12 VDC, 125 mA @ 48 VDC

Operating Temperature Standard models: 0 to 60°C (32 to

140°F)

Wide temp. models: -40 to 75°C (-

to 167°F) for –T model

Ambient Relative Humidity

5 to 95% RH

Dimensions

36 x 105 x 140 mm

(1.42 x 4.13 x 5.51 in)

Reliability

Alert Tools

Built-in buzzer and RTC

MTBF

513,139 hrs

1. DEMKO Certification number: 13 ATEX 1307610X

IEC Certification Number: IECEx UL 13.0051X;

2. Ambient Temperature Range (-40°C ≤ Tamb ≤ 75°C)

3. Certification String: Ex nA nC IIC T3 Gc

4. Standards Covered: EN 60079-0:2012/IEC 60079-0 6th Ed.

AND EN 60079-15:2010/IEC 60079-15 4th Ed.

5. The conditions of safe usage:

a. The Ethernet Communications Devices are intended for

mounting in a tool-accessible IP54 enclosure and used in

an area of not more than pollution degree 2 as defined by

IEC 60664-1.

b. Conductors suitable for use in an ambient temperature

greater than 86°C must be used for the power supply

terminal.

c. A 4mm2conductor must be used when connection to the

external grounding screw is utilized.

d. Provisions shall be made, either in the equipment or

external to the equipment, to prevent the peak rated

voltage being exceeded by the transient disturbances of

more than 140%.

Terminal Block (Plug mated with Socket): Rated 300 V, 10 A,

105°C, 12-28 AWG (0.0804 mm2- 3.31 mm2) wire size, torque

value 4.5 lb-in (0.509 N-m). The input terminal cable size 14 AWG

(2.1 mm2).

Moxa Inc.

Fl. 4, No. 135, Lane 235, Baoqiao Rd.

Xindian Dist., New Taipei City, 23145

Taiwan, R.O.C.

Otros manuales para MGate 5105-MB-EIP

Tabla de contenidos

Otros manuales de Puerta de Moxa Technologies

Moxa Technologies

Moxa Technologies MGate 5135 Series Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3470A-LTE Manual de instalación y operación

Moxa Technologies

Moxa Technologies MGate 5217 Series Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP-T Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3100 Series Manual de usuario

Moxa Technologies

Moxa Technologies AIG-500 Series Instrucciones de uso

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Manual de usuario

Moxa Technologies

Moxa Technologies OnCell Series Manual de usuario

Moxa Technologies

Moxa Technologies 6110 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5134 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6110 Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3180 Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3100 Series Manual de usuario

Moxa Technologies

Moxa Technologies MRC Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3150A-LTE-EU-T Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3111 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Manual de usuario

Moxa Technologies

Moxa Technologies AIG-301 Series Manual de usuario

Moxa Technologies

Moxa Technologies MGate 4101-MB-PBS Manual de usuario

Moxa Technologies

Moxa Technologies AIG-100 Series Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3180 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5122 Series Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5109 Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3170 Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario