Moxa Technologies UC-8580 Series Manual de usuario

P/N: 1802085800012

*1802085800012*

UC-8580 Series

Quick Installation Guide

Version 3.1, January 2021

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The UC-8580 Series computer is a programmable communication-centric

gateway offering a rich variety of communication interfaces, such as

Ethernet, serial, and digital inputs/outputs. This EN 50155-compliant

computer is built for rail applications and comes with multiple wireless

WAN gateway interfaces, making it an ideal choice for building wireless

communication infrastructure with 802.11 a/b/g/n/ac and for LTE data

collection and transmission.

Model Names and Package Checklist

The UC-8580 Series consists of the following models:

Antenna

Connector

Type

Model

Name

Operating

Temperature

Conformal

Coating

SMA

UC-8580-LX

-25 to 55°C (-13 to 131°F)

–

UC-8580-T-LX

-40 to 70°C (-40 to 158°F)

–

UC-8580-T-CT-LX

-40 to 70°C (-40 to 158°F)



QMA

UC-8580-Q-LX

-25 to 55°C (-13 to 131°F)

UC-8580-T-Q-LX

-40 to 70°C (-40 to 158°F)

UC-8580-T-CT-Q-LX

-40 to 70°C (-40 to 158°F)



The UC-8580 Series computer is shipped with the following items:

•UC-8580 Series computer

•CBL-4PINDB9F-100: 4-pin pin header to DB9 female console port

cable, 100 cm

•Quick installation guide (printed)

•Warranty card

Appearance

The UC-8580 comes in two different front-panel models to support the

two different types of antenna connectors (SMA and QMA) for wireless

modules. The GPS antenna connector is secured to the front panel by

default. The SMA model uses the SMA connector for all antennas while the

QMA model uses a TNC connector for the GPS antenna and QMA

connectors for all other antennas.

- 3 -

Front View

SMA Model

QMA Model

LED Indicators

Refer to the following table for the LED indicator definitions.

LED Name

Status

Function

Green

Power is on

Off

No power input or any other power-input error

Green

System is ready

Off

System is booting up, OS boot-up failure, or any

other system initialization error

Ethernet

(located next

to the

Ethernet

ports)

Green

Steady On: 100 Mbps Ethernet link

Blinking: Data transmission is in progress

Yellow Steady On: 1000 Mbps Ethernet link

Blinking: Data transmission is in progress

Off

Data transmission speed at 10 Mbps or the data

cable is not connected

Serial

Green

Tx: Data transmission is in progress

Yellow

Rx: Receiving data

Off

No operation on the serial ports

- 4 -

LED Name

Status

Function

Green

Data is being accessed from either the eMMC or

the mSATA module

Off

No data is being accessed

PGM

Red

Programmable LED for user-defined function

Wireless

Green

The number of glowing LEDs indicate the

wireless signal strength as follows:

3 Green: Excellent

2 Green: Good

1 Green: Poor

Off

No wireless signal

Installing the Computer

Wall or Cabinet Mounting

Use two screws per side to mount the UC-8580 computer on a wall or in

a cabinet. The illustration below shows an SMA model.

Wiring Requirements

Be sure to read and follow these common safety precautions before

proceeding with the installation of any electronic device:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communication wiring together with power

wiring in the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•Use the type of signal transmitted through a wire to determine which

wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

•Keep input wiring and output wiring separate.

•It is advisable to label the wiring to all devices in the system.

- 5 -

ATTENTION

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

UC-8580 computer.

Wiring Caution!

Calculate the maximum possible current in each

power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire size. If the current goes

above the maximum ratings, the wiring could overheat, causing

serious damage to your equipment.

Temperature Caution!

e careful when handling the unit. When the unit is plugged in,

the internal components generate heat, and consequently the

outer casing may feel hot to the touch.

Connecting the Power

Connect the 24 to 110 VDC power line with M12 A-coded connector to the

UC-8580 computer. If the power is supplied properly, the “P” LED will

glow a solid green after a 25 to 30-second delay. The power input location

and pin definition are shown in the following figures. The illustration

below shows an SMA model:

Grounding the Unit

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting the power.

Please note that this product is intended to be mounted on a

well-grounded mounting surface, such as a metal panel. The grounding

connected is provided and located on the front panel. Connect the

grounding wire to an appropriate grounded metal surface.

- 6 -

SMA Model

Connecting to the Network

The pin assignments for the UC-8580 computer’s Ethernet port are shown

in the following figure. If you are using your own Ethernet cable, make

sure that you match the pin assignment on the connector of the Ethernet

cable to the pin assignment shown below. The illustration below shows an

SMA model.

Connecting a Serial Device

Use a serial cable to connect your serial device to the computer’s serial

port. Serial ports P1 and P2 use terminal blocks and can be configured for

RS-232, RS-422, or RS-485 communication. The pin location and

assignment are shown in the following diagrams. The illustration below

uses an SMA model.

- 7 -

RS-232

TxD

RxD

RTS

CTS

GND

RS-422

TxD+

TxD-

RxD+

RxD-

GND

RS-485

–

DATA+

DATA-

GND

Connecting Digital Input/Output Devices

The UC-8580 computer comes with a 3-channel digital input and a

3-channel digital output terminal block that you can use to connect your

digital devices. The DI/O pin assignments and wiring methods are shown

below. The illustration below uses an SMA model:

Connecting a USB Device

The UC-8580 computer is provided with a USB 3.0 port on the front panel

for connecting a USB device. The illustration below shows an SMA model.

- 8 -

Connecting the Wi-Fi/Cellular Module and Antenna

The UC-8580 computer is provided with four sets of antenna holes for

installing antennas for the Wi-Fi and cellular modules. Unfasten the four

screws on the front panel and lift up the panel to check the location of the

Wi-Fi/cellular module sockets. The illustration below shows an SMA

model.

Socket Name

Usage

Cellular_1

Cellular module

Cellular_2

Cellular module

Cellular_3

Cellular module

Wi-Fi_4

Wi-Fi module

You will need to install the SIM cards for the cellular modules in the

designated SIM-card slots. For the cellular module in socket 1, insert SIM

cards in the SIM 1-1 and SIM 1-2 slots. The SIM cards for the cellular

module in socket 3 should be inserted in the SIM 3-1 and SIM 3-2 slots.

The Wi-Fi/cellular module package includes 1 wireless (Wi-Fi or cellular)

module, 2 or 3 antenna cables and connectors, 1 black tape, 1 tag sheet,

2 screws, 2 locking washers, and 2 nuts.

- 9 -

Accessories for the SMA Model

Accessories for the QMA Model

To install a wireless (Wi-Fi/cellular) module, do the following:

1. Remove the plastic protective

film on the thermal pads

attached to the wireless

module.

2. Insert the wireless module in

the designated socket and

tighten the two screws on the

module.

- 10 -

3. Attach the flat end of an antenna cable

to the connector marked MAIN on the

module and insert the

other end of the

cable (with the connector tube) into

the

antenna hole marked MAIN

on the front

panel of the computer. You must first

remove the black cover o

n the antenna

hole and insert the connector tube

through the back side of the front panel

before you can attach the antenna

cable. Follow the procedure described

above to attach the AUX antenna cable.

4. Use the black tape provided in the package to secure the antenna

cables to the module. Attach tags (also provided in the package) to

the cables as shown in the picture below so that you can identify

them.

5. Insert the antenna connectors through the D-shaped antenna holes

on the front panel. Be sure to align the D shape of the connector

tube with the antenna holes before you do so.

Secure the antenna connectors to the front panel by inserting the

locking washers through the connector tube followed by the nut and

then tightening the nut onto the threaded protection ring.

SMA Model

QMA Model

Otros manuales para UC-8580 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Puerta de Moxa Technologies

Moxa Technologies

Moxa Technologies MGate 4101-MB-PBS Manual de usuario

Moxa Technologies

Moxa Technologies SMG-6100 Manual de usuario

Moxa Technologies

Moxa Technologies OnCell Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort Z3150 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5111 Manual de usuario

Moxa Technologies

Moxa Technologies MGate EIP3000 Manual de usuario

Moxa Technologies

Moxa Technologies MGate W5108 series Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5122 Series Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3170 Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3170I Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Manual de usuario

Moxa Technologies

Moxa Technologies AIG-501-T-AZU-LX Manual de usuario

Moxa Technologies

Moxa Technologies MGate W5208 series Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3180 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5103 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN-T Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5600-8-DTL Series Manual de usuario

Moxa Technologies

Moxa Technologies MGate-4101-MB-PBS Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3470A-LTE Manual de instalación y operación

Moxa Technologies

Moxa Technologies OnCell G3111 Manual de usuario

Moxa Technologies

Moxa Technologies MGate W5108 series Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Manual de usuario

Moxa Technologies

Moxa Technologies 4101I-MB-PBS-T Manual de usuario

Moxa Technologies

Moxa Technologies UC-8580-T-CT-LX Instrucciones de uso

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario