Moxa Technologies UC-2100-W Series Manual de usuario

P/N: 1802021000211

*1802021000211*

UC-2100-W Series

Quick Installation Guide

Version 2.0, October 2019

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The UC-2100-W Series computing platform is designed for embedded

data acquisition and processing applications. The computer comes with

up to two software-selectable RS-232/422/485 full-signal serial ports

and single or dual Ethernet LAN ports. In addition, the Arm-based

computing platform is available in various models that can fulfill diverse

interface requirements, such as dual serial, LAN ports, and wireless

connections. These versatile communication capabilities let users

efficiently adapt the palm-sized computing platform to a variety of

complex communications solutions.

Model Names and Package Checklist

The UC-2100-W Series includes the following models:

•UC-2114-T-LX

•UC-2116-T-LX

Before installing a UC-2100-W computer, verify that the package

contains the following items:

•UC-2100-W Series computer

•Console cable

•Power jack

•Quick Installation Guide (printed)

•Warranty card

Notify your sales representative if any of the above items are missing

or damaged.

NOTE

The console cable and power jack can be found inside the

product box, beneath the molded-pulp cushion.

- 3 -

Appearance

UC-2114

UC-2116

- 4 -

LED Indicators

The function of each LED is described in the table below:

LED Name

Status

Function

Power

Green

Power is on, and the device is

functioning normally

Off

Power is off

Ethernet

(10/100 Mbps)

Green

Steady On: 10 Mbps Ethernet link

Blinking: Data transmission is in

progress

Yellow

Steady On: 100 Mbps Ethernet link

Blinking: Data transmission is in

progress

Off

Speed lower than 10 Mbps or the

cable is not connected

Ethernet

(10/100/1000

Mbps)

Green

Steady On: 100 Mbps Ethernet link

Blinking: Data transmission is in

progress

Yellow Steady On: 1000 Mbps Ethernet link

Blinking: Data transmission is in

progress

Off

Speed lower than 10 Mbps or the

cable is not connected

Serial (Tx)

Green

Serial port is transmitting data

Off

Serial port is not transmitting data

Serial (Rx)

Yellow

Serial port is receiving data

Off

Serial port is not receiving data

User

Green/Yellow

User Programmable

LEDs that

indicate the

Wireless

signal strength

Yellow

The number of glowing LEDs

indicates the signal strength

3 LEDs: Excellent

2 LEDs : Good

1 LED : Poor

Off

Wireless module is not detected

CAN1/CAN2 (Tx)

Green

CAN port is transmitting data

Off

CAN port is not transmitting data

CAN1/CAN2 (Rx)

Green

CAN port is receiving data

Off

CAN port is not receiving data

Reset Button

The UC-2100-W Series computer is provided with a reset button, which

is located on the top panel of the computer. To reboot the computer,

press the reset button less than 1 second. Press and hold the reset

button between 7 to 9 seconds to reset the computer to the factory

default settings. When the reset button is held down, the User LED will

blink twice every second. The User LED will become steady when you

hold the button continuously for 7 to 9 seconds. Release the button

within this period to load the factory default settings.

- 5 -

Installing the Computer

Wall or Cabinet Mounting

Use two screws per side to mount the UC-2100-W Series on a wall or

inside a cabinet.

Wiring Requirements

Be sure to read and follow these common safety precautions before

proceeding with the installation of any electronic device:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE

Do not run signal or communication wiring and power wiring in

the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•Use the type of signal transmitted through a wire to determine

which wires should be kept separate. The rule of thumb is that

wiring that shares similar electrical characteristics can be bundled

together.

•Keep input wiring and output wiring separate.

•It is strongly advised that you label wiring to all devices for easy

identification.

ATTENTION

This equipment is intended to be used in Restricted Access

Locations.

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

UC-2100-W Series computers.

Wiring Caution!

Calculate the maximum possible current in each power wire

and common wire. Observe all electrical codes dictating the

maximum current allo

wable for each wire size. If the current

goes above the maximum ratings, the wiring could overheat,

causing serious damage to your equipment.

- 6 -

CAUTION

Be careful when handling the unit. When the unit is plugged in,

the internal components generate

heat, and consequently the

outer casing may feel hot to the touch.

Connecting the Power

Connect the 9 to 48 VDC power line to the

terminal block, which is connected to the UC-

2100-W Series computer. If the power is

supplied properly, the “Power” LED will glow a

solid green light. The power input location and

pin definition are shown in the adjacent

diagram. The input terminal block (CN5) is

suitable for a wire size of 12 to 30 AWG (3.3 to

0.05 mm2) and a torque value of 0.5 N-m

(4.425 lb-in).

MPORTANT

This product is intended to be supplied by a UL Listed power

adapter

or DC power source whose output meets SELV/LPS.

The power source must be

rated 9 to 48 VDC, minimum 0.6 A,

and minimum Tma = 75°C.

Grounding the Unit

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from

the terminal block connector to the grounding surface prior to

connecting the power. Please note that this product is intended to be

mounted on a well-grounded mounting surface, such as a metal panel.

The minimum cross-sectional area of the earthing conductor shall be

equal to the input wiring cable.

Connecting to the Console Port

The UC-2100-W console port is a 4-pin pin-header RS-232 port located

on the right panel of the case. It is designed for serial console

terminals, which are useful for viewing the boot up message, or for

debugging system boot up issues. Remove the protective cover on the

port to connect the console cable.

- 7 -

Serial Console Port & Pinouts

Serial Console Cable

Signal

TxD

RxD

GND

Connecting to the Network

The Ethernet ports are located on the top or bottom panel of the UC-

2100-W computers. The pin assignments for the Ethernet port are

shown in the following figure. If you are using your own cable, make

sure that the pin assignments on the Ethernet cable connector match

the pin assignments on the Ethernet port.

10/100 Mbps

10/100/1000 Mbps

Tx+

TRD(0)+

Tx-

TRD(0)-

Rx+

TRD(1)+

–

TRD(2)+

–

TRD(2)-

Rx-

TRD(1)-

–

TRD(3)+

–

TRD(3)-

Connecting to a Serial Device

The serial ports are located on the bottom panel

of the

UC-2100-W computer. Use a serial cable

connect your serial device to the computer’s

ser

ial port. These serial ports have male DB9

connectors and can be configured for RS

-232,

-422, or RS-485 communication. The pin

location and assignments are shown in the

following table.

Pin RS-232 RS-422

RS-485

(4-wire)

RS-485

(2-wire)

DCD

TxDA(-)

–

RxD

TxDB(+)

–

TxD

RxDB(+)

DataB(+)

DTR

RxDA(-)

DataA(-)

GND

DSR

–

RTS

–

CTS

–

- 8 -

Connecting to a CAN Device

The UC-2114 and UC-2116 come with two CAN ports, which use the 5-

pin terminal block and are compatible with the CAN 2.0A/B standard.

The pin assignment of the port is shown below.

Signal

GND

Chassis

Vout

Installing SIM Cards

You will need to install a SIM card on your UC-2100-W computer.

Follow these steps to install the SIM card.

1. Remove the screw on the cover located

on the right panel.

2. Insert the SIM card into the socket.

Make sure you place the chip-side on

the bottom.

3. To remove the SIM card, simply push

the SIM card and release it.

Installing the microSD Card

Both UC-2114 and UC-2116 come with a storage socket that allows

users to install one microSD card. Follow these steps to install the

microSD card:

1. The microSD socket is located

below the

right panel of the computer. Unfasten

the screw and remove the right panel

cover.

2. Insert the microSD card into the socket

Ensure that the card is inserted in the

right direction.

3. Replace the cover and fasten the screw

on the cover to secure the cover.

To remove the

microSD

card, simply push the

card in and release it.

Adjusting the DIP Switch

The UC-2114 and UC-2116 computers come with one DIP switch for

users to adjust the serial port parameters. To set up the DIP switch, do

the following:

- 9 -

1. Remove the screws on the DIP switch cover

located on the rear panel of the computer.

2. Remove the thin film on the DIP switch and

adjust the setting as required.

Refer to the table below for the DIP switch

settings. The default value is OFF.

Low

High

Term.

–

1 KΩ

120 Ω

–

OFF

150 KΩ

–

Real-time Clock

The real-time clock in the UC-2100-W is powered by a lithium battery.

We strongly recommend that you do not replace the lithium battery

without the help of a Moxa support engineer. If you need to change the

battery, contact the Moxa RMA service team.

ATTENTION

There is a risk of explosion if the battery is replaced wi

th an

incorrect type of battery

Accessing the UC-2100-W Using a PC

You can use a PC to access the UC-2100-W by one of the following

methods:

A. Through the serial console port with the following settings:

Baudrate = 115200 bps, Parity = None, Data bits = 8, Stop bits

= 1, Flow Control = None.

ATTENTION

Remember to choose the “VT100” terminal type. Use the

console cable to connect a PC to the UC

-2100-W's serial

console port

B. Using SSH over the network.

Refer to the following IP addresses and login information:

Default IP Address

Netmask

LAN 1

192.168.3.127

255.255.255.0

LAN 2

192.168.4.127

255.255.255.0

Password: moxa

Otros manuales para UC-2100-W Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de Moxa Technologies

Moxa Technologies

Moxa Technologies V2416 Series Manual de usuario

Moxa Technologies

Moxa Technologies DRP Series Manual de usuario

Moxa Technologies

Moxa Technologies MPC-2240 Series Manual de usuario

Moxa Technologies

Moxa Technologies MPC-2120 Series Instrucciones de uso

Moxa Technologies

Moxa Technologies MC-7130-MP Manual de usuario

Moxa Technologies

Moxa Technologies V2406A Series Manual

Moxa Technologies

Moxa Technologies V3200 Series Manual de usuario

Moxa Technologies

Moxa Technologies DA-683 Series Manual de usuario

Moxa Technologies

Moxa Technologies DA-682A-DPP Series Manual de usuario

Moxa Technologies

Moxa Technologies V3200 Series Instrucciones de uso

Moxa Technologies

Moxa Technologies UC-7101 Instrucciones de uso

Moxa Technologies

Moxa Technologies UC-8410A Series Instrucciones de uso

Moxa Technologies

Moxa Technologies EM-1240-LX Manual de usuario

Moxa Technologies

Moxa Technologies UC-7402 Manual de usuario

Moxa Technologies

Moxa Technologies DRP Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8410 Manual de usuario

Moxa Technologies

Moxa Technologies DA-820 Series Manual de usuario

Moxa Technologies

Moxa Technologies IA260 series Manual de usuario

Moxa Technologies

Moxa Technologies UC-7400 Manual de usuario

Moxa Technologies

Moxa Technologies V2406A Series Manual de usuario

Moxa Technologies

Moxa Technologies V2406C Series Instrucciones de uso

Moxa Technologies

Moxa Technologies UC-8100-LX Instrucciones de montaje

Moxa Technologies

Moxa Technologies DA-720-C5-DPP Manual de usuario

Moxa Technologies

Moxa Technologies MC-1100 Series Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario