Motorola EX-3524 Manual de usuario

Motorola Solutions

EX-3524/EX-3548

Layer 2 Gigabit Ethernet PoE/PoE+ Switch

Installation Guide

2 EX-3524/EX-3548 Layer 2 Gigabit Ethernet PoE/PoE+ Switch

MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions,

Installation Guide 3

1.0 Introduction ......................................................5

1.1 Unpacking ......................................................5

1.2 Document Conventions ............................................5

1.3 Warnings .......................................................6

1.4 Site Preparation ..................................................7

1.5 Selecting a Site ..................................................7

2.0 Specifications ....................................................8

2.1 Physical Specifications ............................................ 8

2.2 Environmental Specifications ....................................... 8

2.3 Electrical Specifications ........................................... 8

2.4 Power Cord Specifications .......................................... 9

2.4.1 Power Protection ............................................. 9

2.5 Switch Description ................................................ 9

2.5.1 Port LEDs .................................................. 10

2.5.2 10/100/1000BASE-T RJ-45 Ports................................ 10

2.5.3 Gigabit SFP Slots ............................................ 10

2.5.4 Mode Button ............................................... 10

2.5.5 Console Port ............................................... 10

2.5.6 System LEDs ............................................... 10

2.5.7 Reset Button ............................................... 10

2.5.8 Ground Point ............................................... 10

2.5.6 AC Power Socket ............................................ 11

2.6 LED Codes ..................................................... 12

2.6.1 System Status LEDs ......................................... 12

2.6.2 Port Status LED ............................................. 13

3.0 Hardware Setup .................................................. 14

3.1 Rack Mount Installation ........................................... 14

3.2 Shelf or Desktop Installation ....................................... 17

3.3 Power and Grounding ............................................ 18

4 EX-3524/EX-3548 Layer 2 Gigabit Ethernet PoE/PoE+ Switch

3.4 Port Connections ................................................ 19

3.4.1 Installing SFP Transceivers .................................... 19

3.4.2 Connecting Twisted-Pair Cables ................................ 20

3.4.3 Cable Requirements .......................................... 21

3.4.4 Power-over-Ethernet ......................................... 21

3.4.5 Connecting to SFP Ports ...................................... 22

4.0 Switch Management .............................................. 24

4.1 Connecting to the Console Port ..................................... 24

4.2 Resetting the Switch ............................................. 25

5.0 Regulatory Information ............................................ 26

5.1 Radio Frequency Interference Requirements - FCC ...................... 26

5.2 Radio Frequency Interference Requirements - Canada ................... 26

5.3 CE Marking and European Economic Area (EEA) ........................ 27

5.4 Statement of Compliance ......................................... 27

5.5 PSE Alarm ..................................................... 27

5.6 Power Cord Safety ............................................... 28

5.7 Waste Electrical and Electronic Equipment (WEEE) ..................... 31

5.7.1 Turkish WEEE Statement of Compliance .......................... 32

6.0 Motorola Solutions Support Center ................................. 33

Installation Guide 5

1 Introduction

The Motorola Solutions EX-3524 and EX-3548 are Gigabit Ethernet Layer 2 switches with either 24 or 48

10/100/1000-BASE-T ports, and four Small Form Factor Pluggable (SFP) transceiver slots for fiber connectivity. The

switches are built with leading-edge technology to deliver reliable high-performance connectivity for your data

network.

All of the 10/100/1000 Mbps ports on the switches support both the IEEE 802.3af and IEEE 802.3at-2009 PoE

standards.

Each switch also includes an SNMP-based management agent, which provides both in-band and out-of-band

access for managing the switch.

This document is written for the professional installer deploying EX-3524 and EX-3548 switches.

1.1 Unpacking

Verify that you have the equipment listed below:

• EX-3524 or EX-3548 switch

• Rack Mounting Kit containing two brackets and eight screws for attaching the brackets to the switch

• Console cable— RJ-45 to DB-9

• Four adhesive foot pads

•EX-3524/EX-3548 Layer 2 Gigabit Ethernet Switches Installation Guide (this document)

Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment,

contact Motorola Solutions Support immediately. Contact information is available at

https://portal.motorolasolutions.com/Support/US-EN.

1.2 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or equipment

malfunction.

6 EX-3524/EX-3548 Layer 2 Gigabit Ethernet PoE/PoE+ Switch

Translations of this manual, including all appropriate warnings and cautions, can be found at

https://portal.motorolasolutions.com/Support/US-EN/Wireless+Networks.

1.3 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment installation before

connecting the system to its power source.

• Remove jewelry and watches before installing this equipment.

• Install the equipment in a rack with adequate dimensions and weight allowances.

• Verify any device connected to this unit is properly wired and grounded.

• Connect all power cords to a properly wired and grounded electrical circuit.

• Verify the electrical circuits have appropriate overload protection.

• There is a risk of explosion if the battery supplied with this product is replaced with an incorrect type of

battery. Dispose of used batteries according to the instructions.

• Motorola strongly recommends the use of an Uninterruptible Power Supply (UPS) that supports the

EX-3524/EX-3548 switch power rating. Not using a UPS can result in data loss or equipment damage due

to a power surge or power failure.

• Verify that the power connector and socket are accessible at all times during the operation of the

equipment.

• Do not work with power circuits in dimly lit spaces.

• Do not install this equipment or work with its power circuits during thunderstorms or other weather

conditions that could cause a power surge.

• Verify there is adequate ventilation around the device, and ambient temperatures meet equipment

operation specifications.

• This product is designed for in building installation only and is not intended to be connected to exposed

(outside plant) networks.

• This product uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the

requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you

should never look directly at a transmit port when it is powered on.

• When selecting a fiber SFP device, considering safety, please make sure that it can function at a

temperature that is not less than the recommended maximum operational temperature of the product. You

must also use an approved Laser Class 1 SFP transceiver.

• Use only twisted-pair cables that conform to FCC standards with RJ-45 connectors.

WARNING! Indicates a condition or procedure that could result in personal injury or equipment

damage.

Installation Guide 7

1.4 Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment placement, port

capacity, power drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify where all installed components are located.

• Verify appropriate rack mounting requirements, as required.

• Provide a sufficient number of power drops for your equipment.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify that cable lengths are within the maximum allowable distances for optimal signal transmission.

• Verify that the device is powered through an Uninterruptible Power Supply (UPS).

1.5 Selecting a Site

Switch units can be mounted in a standard 19 inch equipment rack or on a flat surface. Be sure to follow the

guidelines listed below when choosing a site:

• Locate the switch unit at the center of all devices you want to link and near a power outlet.

• Maintain a temperature range within 0°to 50°C/32°to 122°F and humidity range within 10% to 90%

non-condensing.

• Provide adequate space (approximately 2 inches) on all sides for proper air flow.

• Confirm access for installing, cabling, and maintaining all devices.

• Install the switch unit so that status LEDs are clearly visible.

• Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.

• Ensure that twisted-pair cables are always routed away from power lines, fluorescent lighting fixtures,

and other sources of electrical interference, such as radios and transmitters.

• Ensure that the unit is connected to a separate grounded power outlet that provides 100 to 240VAC and

50 to 60Hz power levels.

• Ensure that the unit is within 6.6 ft / 2m of each device that is powered from an independent circuit

breaker.

• Use of a filter or circuit breaker is recommended.

8 EX-3524/EX-3548 Layer 2 Gigabit Ethernet PoE/PoE+ Switch

2 Specifications

2.1 Physical Specifications

2.2 Environmental Specifications

2.3 Electrical Specifications

Form factor 1U rack mount

Dimensions

(WxDxH)

EX-3524: 44.0 x 28.0 x 4.4 cm (17.32 x 11.00 x 1.73 in)

EX-3548: 44.0 x 40.9 x 4.4 cm (17.32 x 16.10 x 1.73 in)

Weight

EX-3524: 3.6 kg (7.83 lb)

EX-3548: 6.6 Kg (14.55 lb)

Operating temperature 0° C to 50° C (32° F to 122° F)

Operating humidity 10% to 90% (non-condensing)

Operating altitude EX-3524: 4004 m (13,136 ft)

EX-3548:2000 m (6, 561 ft)

Storage temperature -40° C to 70° C (-40° F to 158° F)

Storage humidity 10% to 90% (non-condensing)

Storage altitude 4572 m (15,000 ft)

AC input voltage

EX-3524: AC 100-240 V, 50-60 Hz, 6 A

EX-3548: AC 100-240 V, 50-60 Hz, 12 A

PoE power output

EX-3524: Up to 370 W

EX-3548: Up to 740 W

Installation Guide 9

2.4 Power Cord Specifications

A power cord is not supplied with the EX-3524/EX3548 switch. Use only a correctly rated power cord certified (as

appropriate) for the country of operation.

2.4.1 Power Protection

•If possible, use a circuit dedicated to data processing equipment. Commercial electrical

contractors are familiar with wiring for data processing equipment and can help with the load balancing

of these circuits.

•Install surge protection. Be sure to use a surge protection device between the electricity source and

the EX-3524/EX-3548 switch.

•Install an Uninterruptible Power Supply (UPS). A UPS provides continuous power during a power

outage. Some UPS devices have integral surge protection. UPS equipment requires periodic maintenance

to ensure reliability. A UPS of the proper capacity for the data processing equipment must be purchased.

2.5 Switch Description

The EX-3524 (top) and EX-3548 (bottom) are shown in the drawings below. The switches consist of several key

hardware components. This manual describes each specific component, or related components, together with

their installation requirements and procedures.

10 EX-3524/EX-3548 Layer 2 Gigabit Ethernet PoE/PoE+ Switch

2.5.1 Port LEDs

For information on port status LED indicators, see Port Status LEDs on page 13.

2.5.2 10/100/1000BASE-T RJ-45 Ports

The switch contains 24 10/100/1000BASE-T RJ-45 ports that support 10/100/1000BASE-T copper links to other

devices. For more information, see Connecting Twisted-Pair Cables on page 20.

2.5.3 Gigabit SFP Slots

The switch contains four Small Form Factor Pluggable (SFP) transceiver slots that operate up to Gigabit full duplex.

For more information, see Connecting to SFP Ports on page 22.

2.5.4 Mode Button

Pressing the Mode button on the front panel will change the Diag LED to display PoE status. For more information,

see LED Codes on page 12.

2.5.5 Console Port

The RJ-45 connector on the front panel far right side that is labeled “Console” provides an out-of-band serial

connection to a terminal or a PC running terminal emulation software. The port can be used for performing switch

monitoring and configuration. For more information, see Connecting to the Console Port on page 24.

2.5.6 System LEDs

For information on system status LED indicators, see LED Codes on page 12.

2.5.7 Reset Button

Pressing the reset button on the rear panel causes the switch to execute a hard reset. For more information, see

Resetting the Switch on page 26.

2.5.8 Ground Point

The switch should be connected to ground using this screw connection. For more information on how to connect

ground to the switch, see Power and Grounding on page 18.

Otros manuales para EX-3524

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Motorola

Motorola

Motorola BSR 64000 Manual de usuario

Motorola

Motorola WE800G - Wireless EN Bridge Manual de usuario

Motorola

Motorola Netopia 4686-XL Manual de usuario

Motorola

Motorola HMDC5025 Manual de usuario

Motorola

Motorola 49901 - Vanguard 340 Router Manual de usuario

Motorola

Motorola BSR 64000 Manual de usuario

Motorola

Motorola BR700 - EN Broadband Router Manual de usuario

Motorola

Motorola S2500 Manual de usuario

Motorola

Motorola AT&T NVG589 Manual de usuario

Motorola

Motorola WR850G - Wireless Broadband Router Manual de usuario

Motorola

Motorola Netopia 3300 Manual de usuario

Motorola

Motorola ML2410 Manual de usuario

Motorola

Motorola HOTZONE DUO 1.0 Manual de usuario

Motorola

Motorola Netopia 7000 Manual de usuario

Motorola

Motorola MR1700 Manual de usuario

Motorola

Motorola BSR 2000 Manual de usuario

Motorola

Motorola MG7315 Manual de usuario

Motorola

Motorola Wireless Broadband Platform Manual de usuario

Motorola

Motorola MH7021 Manual de usuario

Motorola

Motorola BSR 2000 Manual de usuario

Motorola

Motorola PTP 600 Series Manual de usuario

Motorola

Motorola Motomesh 1.0 Manual de usuario

Motorola

Motorola CPEI 890 Manual de usuario

Motorola

Motorola CPEI 775 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad

LevelOne

LevelOne FBR-1416 Manual de usuario