Motorola 2108-N9 Manual de usuario
User Manual
Gigabit Ethernet Router with HPNA and 802.11n / 2108-N9
Gigabit Ethernet Router with 802.11n / 2108-D9
2
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS – POWER SUPPLY INSTALLATION.
Connect the power supply
cord to the power jack on the Motorola Netopia
®
Gateway. Plug the power supply into an appropriate electri-
cal outlet.
CAUTION:
Depending on the power supply provided with the product, either the direct plug-in power supply
blades, power supply cord plug or the appliance coupler serves as the mains power disconnect. It is impor-
tant that the direct plug-in power supply, socket-outlet or appliance coupler be located so it is readily acces-
sible.
TELECOMMUNICATION INSTALLATION.
When using your telephone equipment, basic safety precau-
tions should always be followed to reduce the risk of fire, electric shock and injury to persons, including
the following:
• Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry
tub, in a wet basement or near a swimming pool.
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electrical shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
PRODUCT VENTILATION.
The Motorola Netopia
®
Gateway is intended for use in a consumer's
home. Ambient temperatures around this product should not exceed 104°F (40°C). It should not be used in
locations exposed to outside heat radiation or trapping of its own heat. The product should have at least one
inch of clearance on all sides except the bottom when properly installed and should not be placed inside
tightly enclosed spaces unless proper ventilation is provided.
SAVE THESE INSTRUCTIONS
Motorola Part Number:
578175-001-00 revision a
Copyright © 2010 by Motorola, Inc.
All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative
work (such as translation, transformation or adaptation) without written permission from Motorola, Inc. Motorola reserves the
right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to
provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or
expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola
may make improvements or changes in the product(s) described in this manual at any time. MOTOROLA and the Stylized M
Logo are registered in the US Patent & Trademark Office. Microsoft, Windows, Windows Me, and Windows NT are either
trademarks or registered trademarks of Microsoft Corporation in the U.S and/or other countries. Macintosh is a registered
trademark of Apple, Inc. Firefox is a registered trademark of the Mozilla Foundation. All other product or service names are the
property of their respective owners.
Safety Information
3
ENGLISH
Thank you for selecting the Motorola Netopia
®
2108-D9 or -N9 Gigabit Ethernet Gateway. This
guide will help you set up and configure your network.
Check your package contents. It should contain the items shown here:
If you don’t have everything, contact your supplier immediately.
Checklist
1
User Manual
Motorola Gateway
Power
Supply
1 Gray RJ-45
Ethernet Cable
1 Yellow RJ-45
Ethernet Cable
Wallmounting Kit
(2 screws + 2 anchors)
Wallmounting
Kit
4
ENGLISH
1.
Select a suitable place on the network to install the Wireless Gateway.
You can stand it up in its stand; lay it flat on a desktop; or mount it on a wall using the
included wall mounting kit hardware (see “Wall Mounting instructions (optional)” on
page 15).
2.
Use standard Cat5 Ethernet cables to connect PCs to the LAN ports on the
rear of the Wireless Gateway.
One is supplied with your Gateway (yellow cable).
3.
Connect the DSL or Cable modem to the gray WAN port on the Wireless Gate-
way.
Use the cable supplied with your DSL/Cable modem. If the cable is missing, a standard
Cat5 Ethernet cable can be used.
4.
Connect the supplied power adapter to the Wireless Gateway.
Use only the power adapter provided. Using a different one may cause hardware dam-
age. Turn the power ON with the ON/OFF Power Switch.
5.
Check the LEDs:
• The Power LED should be ON.
• The LAN LED(s) that have a cable connected should be ON when the connected device
is also on.
• The Wireless LED should be ON only when a wireless client is connected to this
Gateway.
• (
2108-N9 HPNA model only
) The HPNA LED should be ON only when an HPNA
device(s) is connected via coaxial cable.
• The WAN LED should be ON when the WAN Port is connected via Cat5 cabling.
Connections
2
5
ENGLISH
• The Internet LED may initially be OFF. After proper configuration, it should come ON
When all of your connections are made, your network may look like this:
DC Power
Rear View
LAN
Ports
WAN Port
Power Switch
6
ENGLISH
The figure below shows how to connect a Motorola 2108-N9 HPNA-enabled Gateway to
a home coaxial cable network using a Motorola HPNA Adaptor (purchased separately).
Follow the same steps to connect any Ethernet device such as a hub or printer to a coax-
ial cable network.
6.
Enable Wireless devices.
In order to use the Access Point in the Wireless Gateway, other Wireless devices must
use the same SSID and Wireless Security settings as the Wireless Gateway.
In-House
Coax Wiring
Ethernet
wall jack
wall jack
Motorola HPNA Adapter
settop box
Motorola 2108-N9 Gateway
HPNA port
7
ENGLISH
The Wireless Gateway's default settings are as follows.
Ensure the Wireless Gateway and the other Wireless Stations are using the same set-
tings.
• Use the Wireless setup screen to configure the Wireless Access Point in the Wireless
Gateway.
• Configure the Wireless stations (PCs) using your normal method for configuring their
Wireless interface.
• Wireless clients must also be set to use Infrastructure mode.
Setting Wireless Gateway
SSID
Default value:
unique to your Gateway
This may be changed on the Wireless screen, on the Wireless Gateway's main
menu.
Wireless
Default Broadcast SSID:
Disabled
Default Security:
WEP128
Use the Wireless screen on the main menu to change this as required.
8
ENGLISH
When all of your connections are complete, the status LEDs on the front of your Motorola Neto-
pia
®
Gateway will light, in accordance with the following diagram:
LED Definition
Power (Green, Red)
Off = Power Off
Green = Power On
Red = either power supply had become unstable or POST
failed
Blinking Red = Posting
Blinking Green = FW upgrading
Front View
Power
Internet
WAN
LAN 1~4
HPNA (2108-N9 model only)
Wireless
WPS
9
ENGLISH
Internet
Off = No IP connection
Solid Green = IP connection exists
Blinking Green = IP level traffic
WAN
Off = No connection
Solid Green = Connection
Blinking Green = traffic
LAN 1~4
Off = No connection
Solid Green = Connection
Blinking Green = traffic
HPNA
(2108-N9 model only)
Off = No connection
Solid Green = Connection
Blinking Green = traffic
Wireless
Off = No connection
Solid Green = Connection
Blinking Green = traffic
WPS (Green, Yellow, Red)
Off = No action
Solid Green = WPS Success
Blinking Yellow = WPS in progress
Blikng Red = WPS Error or session overlap
LED Definition
10
ENGLISH
You can access the configuration pages at any time as follows:
1.
Run a Web browser, such as Firefox, Safari, or Microsoft Internet Explorer, and
enter
http://192.168.1.254
in the URL Address text box.
Press Return.
2.
When prompted, enter the Username and Password supplied by your ISP, if
required.
Some ISPs do not require Username and Password. Refer to your ISP.
3.
Refer to the data from your ISP, and the table below, to ensure your choices
are correct.
Enter the information supplied by your Internet Service Provider.
Device Configuration
Connection Type Data Required
Dynamic IP Address (DHCP) Usually, none.
Specified (Static) IP Address IP Address allocated to you, and related information.
PPPoE Login name and password.
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Enrutador de red de Motorola
Motorola
Motorola 68390 - Vanguard 320 Router Manual de usuario
Motorola
Motorola BSR 2000 Manual de usuario
Motorola
Motorola EWR6300 Manual de usuario
Motorola
Motorola PTP 600 Series Manual de usuario
Motorola
Motorola MG8702 Manual de usuario
Motorola
Motorola 68390 - Vanguard 320 Router Manual de usuario
Motorola
Motorola Wireless Broadband Platform Manual de usuario
Motorola
Motorola EX-3524 Manual de usuario
Motorola
Motorola 2247 Manual de usuario
Motorola
Motorola EX-3524 Manual de usuario
Motorola
Motorola CPEI 890 Manual de usuario
Motorola
Motorola POWERBROADBAND 45101 Manual de usuario
Motorola
Motorola Netopia R910 Manual de usuario
Motorola
Motorola MotoWI4 PTP 600 Series Manual de instrucciones
Motorola
Motorola HOTZONE DUO 1.0 Manual de usuario
Motorola
Motorola BSR 2000 Manual de programación
Motorola
Motorola SURFboard SBG941 Series Manual de usuario
Motorola
Motorola VL-RISC MCF5202 Manual de usuario
Motorola
Motorola BSR 64000 Manual de usuario
Motorola
Motorola S2500 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad
LevelOne
LevelOne FBR-1416 Manual de usuario