Morphy Richards SEMI-ELECTRONIC 40715 Manual de usuario

Semi-electronic iron steam/spray/shot

Please read and keep these instructions

www.morphyrichards.co.uk

getting the best from

your new iron...

•Safety first

Caution must be used when handling this appliance as it does get

very hot. Always switch off the unit and allow to cool before

cleaning or storing.

•Jet cleaning

Your iron will give the best ironing results and will last longer if you

apply jet cleaning after each period of ironing.

40715 Rev 1 31/5/05 9:11 AM Page 1

Important safety

instructions

The use of any electrical appliance

requires the following common sense safety

rules.

Primarily there is danger of injury or

death and secondly the danger of damage

to the appliance. These are indicated in the

text by the following two conventions:

WARNING: Danger to the person!

IMPORTANT: Damage to the appliance! In

addition we offer the following safety

advice.

Location

•Do not use outdoors.

Children

•Close supervision is necessary when any

appliance is used near children.

Personal safety

•WARNING: Burns can occur from

touching hot metal parts, hot water

or steam. Use caution when you

turn a steam iron upside down,

there may be hot water in the water

tank.

•WARNING: To protect against the

risk of electric shock do not put the

appliance in water or in any other

liquid.

•Do not use the vertical steam feature on

clothes that are being worn.

•Do not leave the iron unattended whilst

plugged in or on an ironing board. Never

allow the mains lead to over hang the

work surface.

•The socket should always be off before

plugging or unplugging from the socket.

Never yank the cord to disconnect from

the socket, instead, grasp plug and pull

to disconnect.

•Do not allow the cord to touch hot

surfaces. Let the iron cool completely

before putting away. Loop cord loosely

around the iron before storing.

Other safety considerations

•Use the iron only for its intended use.

•Always disconnect the iron from the

electrical socket when filling with water

or emptying, and when not in use.

•Do not operate the iron with a damaged

cord or if the iron has been dropped or

damaged. To avoid the risk of electric

shock, do not disassemble the iron, but

telephone Morphy Richards for advice.

Incorrect reassembly can cause a risk of

electric shock when the iron is used.

Special instructions

•If your iron does not work, check the

following points:

Has the temperature control been set to

the required temperature? Is the plug in

its socket? Is the plug itself or the

socket faulty? (Check by plugging in

another appliance).

•WARNING: When not in use, your

iron should never be placed flat and

left on an ironing board.

•To prevent damage to the textile being

ironed, follow the temperature guide

carefully. (Test the inside of the hem of

the garment).

•When ironing is complete, remove the

plug from the socket, empty any

remaining water from the tank, and allow

to cool before storage.

•If you drop or severely knock your iron

this could cause internal damage even if

the outside appears alright. Have it

checked by a qualified electrician.

•It is recommended that you use up one

beaker of water by operating your iron’s

steam and shot of steam functions

before ironing any clothes as some

dripping may occur while your irons

steam system is activated.

40715 Rev 1 31/5/05 9:11 AM Page 2

Electrical

requirements

Check that the voltage on the rating

plate of your appliance corresponds with

your house electricity supply which must be

A.C. (Alternating current).

If the socket outlets in your home are

not suitable for the plug supplied with this

appliance the plug should be removed and

the appropriate one fitted.

WARNING : The plug removed from

the mains lead, if severed, must be

destroyed as a plug with a bared

flexible cord is hazardous if engaged

into a live socket outlet.

Should the fuse in the 13 amp plug

require changing a 13 amp BS1362 fuse

must be fitted.

WARNING: This appliance must be

earthed.

Instructions for use

Temperature guide

Heat setting markings on the function console panel of your Morphy Richards irons match

those of the International Textile Care Labelling Code.

Symbol

(120˚C Max) Cool (160˚C Max) Warm (210˚C Max) Hot

Control knob

positions

Do not

iron at all

Fabric Nylon, Acetates

e.g. Acrilan

Courtelle, Orlon

Triacetates, e.g.

Tricel/Polyester

Wool, Polyester

mixtures e.g.

Polyester/Cotton

Cotton, Linen

Rayon, Rayon

mixtures,

e.g. Rayon/Linen

Ironing Iron on wrong side

if moisture required

use damp cloth

(Not Acetate)

Fabrics requiring this

setting usually require

steam pressing for heavy

cotton, denim etc.

With water in tank Dry and spray Steam/spray/shot of steam

Jet clean

Without water in tank Dry ironing

40715 Rev 1 31/5/05 9:11 AM Page 3

Components of your

iron

⁄ Variable steam button

¤ Shot of steam button

‹ Spray button

› Filling hole with cap

ﬁ Spray nozzle

ﬂSoleplate

‡ Temperature console

· Water tank

‚ Life long anti-scale (certain models only)

„ Filling beaker

‰ Auto shut-off indicator

Before use

Note: The steam facility should only be

used on garments which are suitable for

ironing at the 2, 3 dot settings.

When ironing with the steam facility at

the 2 dot setting, the steam output should

be set at the lower end of the steam range

(see variable steam section).

Textiles and clothes are supposed to

carry ironing instructions. If they don’t you

should follow the fabric guide on page 3,

but be sure to test the temperature by

ironing the hem of the garment or similar

area first.

If you adjust the temperature from a hot

setting to a cooler setting, wait until the iron

temperature has stabilised before you

continue ironing.

It is always a good idea to begin with

cool fabrics and work up to higher settings.

An iron heats up quicker than it cools

down so you’ll save time and electricity.

Filling

1Make sure that the iron is not plugged in

and then set the variable steam control

⁄to the ‘0’ position before filling the

iron with water.

2Lift up the fill cap and fill the water

through the filling hole ›into the water

tank ·, using the beaker provided. A

1 beaker fills the tank (400ml). After

filling replace the fill cap. In hard water

areas the use of distilled or

demineralised water is recommended.

WARNING: Never use battery

topping up fluid or water containing

any substances like starch, or sugar,

or defrosted water from a

refridgerator.

3Always pour out the remaining water

after use.

WARNING: When filling your iron

with tap water always use the beaker

provided. Never fill directly under the

tap.

⁄¤‹

›

ﬁ

ﬂ‡·

‚

„

‰

40715 Rev 1 31/5/05 9:11 AM Page 4

Temperature control

•Default setting + 3 dot (cotton)

•To increase temperature press the top

button.

•To decrease temperature press the

bottom button.

•The light panel will flash to indicate that

the iron has not yet reached the correct

temperature.

• Once the correct temperature has been

reached , the light will stop flashing and

there will be one ‘beep’ to signal that the

iron is now ready for use.

Features of your iron

Dry ironing

You can use your iron as a dry iron only.

Make sure the variable steam control ⁄is

set to the ‘0’ symbol.

Any temperature setting may be used

depending on the garment. The spray

feature may be used provided there is water

in the tank (see filling section). You do not

need to put any water in the tank when dry

ironing only.

Spray

Press the spray button ‹

and aim the spray of water at

stubborn creases. You can do

this whilst dry ironing providing

there is water in the tank. When

using the water spray it may be

necessary to push the button a

few times to get the spray pump primed.

Variable steam

Fill the iron with water as described in

‘Filling’, page 4 and insert the plug into the

electrical socket.

The steam output can be varied from

low to high by turning the variable steam

control C. When using the iron at the

bottom of the steam range, the steam

output should be adjusted to the low

setting.

The steam facility should only be used

on garments which are suitable for ironing

at 2, 3 dot and MAX setting.

Steam off

‘MAX’ steam

Increase

temperature

Decrease

temperature

40715 Rev 1 31/5/05 9:11 AM Page 5

Shot of steam

Press the shot of steam

button ¤to obtain a burst

of extra steam for ironing out

creases in heavy material

such as denim etc.

The shot of steam can be

used whilst dry ironing, providing there is

water in the tank, and the temperature

control is set within the steam range.

Do not use shot of steam at

temperatures below the steam range shown

on the control dial.

Note: For optimum steam quality, do not

operate the shot more than three times in

succession.

Vertical steam

Hold the iron in a vertical position

between 1cm and 2cm away from the item

D. Press the shot of steam button ¤, this

will create vertical steam. This feature is

especially useful for removing creases from

hanging clothes, curtains, wall hangings,

etc.

Note; For optimum steam quality, do not

operate the shot more than three times in

succession.

No drip system

Your iron is fitted with a no drip system

which is designed to prevent water

escaping from the soleplate when the iron is

too cold.

During use, the no drip system may emit

a loud click, particularly during heat-up or

whilst cooling down. This is perfectly

normal and indicates that the system is

functioning correctly.

Auto shut-off

Your iron is fitted with the auto shut-off

function it will automatically shut down after

a set period. The ‘safety switch off’ led will

flash on the function panel.

If the iron is left unattended in the

horizontal position it will shut down after 30

seconds.

If it is left in the vertical position it will

shut down after 8 minutes.

To reactivate the iron gently shake it and

wait for the iron to heat-up as normal.

Life long anti-scale

system

The life long anti-scale system reduces

scale deposits and helps prolong the life of

the iron.

40715 Rev 1 31/5/05 9:11 AM Page 6

Maintenance

Jet cleaning

Your iron has a built in cleaning system

designed to keep the water valve, steam

chamber and steam vents clear of lint and

loose mineral deposits. The ‘jet clean’ should

be operated after each period of ironing.

To operate, ensure that there is little water

in the tank, place the iron on its heel and turn

the temperature control dial to the maximum

setting. Wait for the beep, then unplug the

iron and hold it about 6’’ (150mm) above the

sink in the ironing position. Press the shot of

steam button about 10 times in succession.

After this cleaning operation, empty out

any remaining water.

WARNING: Do not attempt to descale

the soleplate with descaling products.

To clean a stainless steel soleplate

To keep the soleplate of your iron clean

and free of limescale, we recommend that

you use one of the gentle chrome, silver or

stainless steel cleaners that are generally

available. Always follow the manufacturers

instructions. To clean off melted man-made

fibres set the iron at 3 dot position and pass

it over a clean piece of cotton which will

draw the deposit off the surface.

To clean the exterior

Allow the iron to cool and wipe over with

a damp cloth and mild detergent, then wipe

with a dry cloth.

Emptying and storing

When you have

finished ironing, unplug

your iron. Ensure that the

variable steam control is

set at the ‘0’ position, lift

up the fill cap and empty

any remaining water out

of the filling hole.

Do not store in the box, but in an upright

position, so that any drops of water

remaining cannot leak out and discolour the

soleplate.

Important: The flex can be

damaged if wound too tightly

around the iron after use. Make

a loose loop with the flex and

wrap it around the iron. The

iron must be cool before

winding the flex and storing on

its heel.

Helpline

If you have any difficulty with your

appliance, do not hesitate to call us.

We are more likely able to help than the

store from where you bought it.

Please have the following information

ready to enable our staff to deal with your

query quickly.

•Name of the product

•Model number as shown on the underside

of the appliance.

40715 Rev 1 31/5/05 9:11 AM Page 7

Morphy Richards products are intended for

household use only.

Morphy Richards has a policy of continuous

improvement in product quality and design.

The company, therefore reserves the right

to change the specification of its models at

any time.

The After Sales Division

Morphy Richards Ltd, Mexborough

South Yorkshire, England, S64 8AJ

Helpline (office hours)

UK 0870 060 2615

Republic of Ireland 1800 409119

RN40715M UK Rev 1 0304

Your two year guarantee

It is important to retain the retailers

receipt as proof of purchase. Staple your

receipt to this back cover for future

reference.

Please quote the following information if

the product develops a fault. These numbers

can be found on the base of the product.

Model no. Serial no.

All Morphy Richards products are

individually tested before leaving the factory.

In the unlikely event of any appliance proving

to be faulty within 28 days of purchase it

should be returned to the place of purchase

for it to be replaced.

If the fault develops after 28 days and

within 24 months of original purchase, you

should contact the Helpline number quoting

Model number and Serial number on the

product, or write to Morphy Richards at the

address shown. You will be asked to return

the product (in secure, adequate packaging)

to the address below along with a copy of

proof of purchase.

Subject to the exclusions set out below

(see Exclusions) the faulty appliance will then

be repaired or replaced and dispatched

usually within 7 working days of receipt.

If for any reason this item is replaced

during the 2 year guarantee period, the

guarantee on the new item will be calculated

from original purchase date. Therefore it is

vital to retain your original till receipt or

invoice to indicate the date of initial

purchase.

To qualify for the 2 year guarantee the

appliance must have been used according to

the manufacturers instructions. For example

kettles should have been regularly descaled.

EXCLUSIONS

Morphy Richards shall not be liable to

replace or repair the goods under the terms

of the guarantee where:

1The fault has been caused or is

attributable to accidental use, misuse,

negligent use or used contrary to the

manufacturers recommendations or where

the fault has been caused by power

surges or damage caused in transit.

2The appliance has been used on a voltage

supply other than that stamped on the

products.

3Repairs have been attempted by persons

other than our service staff (or authorised

dealer).

4Where the appliance has been used for

hire purposes or non domestic use.

5Morphy Richards are not liable to carry

out any type of servicing work, under the

guarantee.

6Plastic filters for all Morphy Richards

kettles and coffee makers are not covered

by the guarantee.

This guarantee does not confer any rights

other than those expressly set out above and

does not cover any claims for consequential

loss or damage. This guarantee is offered as

an additional benefit and does not affect your

statutory rights as a consumer.

•This guarantee is valid in the UK and

Ireland only.

40715 Rev 1 31/5/05 9:11 AM Page 8

Otros manuales para SEMI-ELECTRONIC 40715

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hierro de Morphy Richards

Morphy Richards

Morphy Richards POWER STEAMELITE Manual de usuario

Morphy Richards

Morphy Richards 40850 COMFIGRIP IRON Manual de usuario

Morphy Richards

Morphy Richards SEMI-ELECTRONIC IRON RN40692 Manual de usuario

Morphy Richards

Morphy Richards TURBOSTEAM 40659 Manual de usuario

Morphy Richards

Morphy Richards Orbit Manual de usuario

Morphy Richards

Morphy Richards 40725 Manual de usuario

Morphy Richards

Morphy Richards Turbo steam iron Manual de usuario

Morphy Richards

Morphy Richards INTELLIDOME Manual de usuario

Morphy Richards

Morphy Richards Precise Steam Plus Manual de usuario

Morphy Richards

Morphy Richards Comfigrip Advanced 40715 Manual de usuario

Morphy Richards

Morphy Richards IB42345 Manual de usuario

Morphy Richards

Morphy Richards 40707 Manual de usuario

Morphy Richards

Morphy Richards JET STREAM Manual de usuario

Morphy Richards

Morphy Richards VAPOCARE Manual de usuario

Morphy Richards

Morphy Richards IB42270 Manual de usuario

Morphy Richards

Morphy Richards Semi-electronic iron Manual de usuario

Morphy Richards

Morphy Richards Steam Generator ironing system Manual de usuario

Morphy Richards

Morphy Richards RN40655 Manual de usuario

Morphy Richards

Morphy Richards RN303100MUK Manual de usuario

Morphy Richards

Morphy Richards Cruiser Manual de usuario

Morphy Richards

Morphy Richards Steam Generator Manual

Morphy Richards

Morphy Richards IB303106EE Manual de usuario

Morphy Richards

Morphy Richards IB40621 Manual de usuario

Morphy Richards

Morphy Richards breeze Manual de usuario

Manuales populares de Hierro de otras marcas

Clatronic

Clatronic DB 3703 Manual de usuario

TEFAL

TEFAL FV4093Z0 Manual de usuario

Gorenje

Gorenje SIH 2200 BS Manual de usuario

Philips

Philips GC6012 Manual de usuario

Bosch

Bosch 2 Series Manual de usuario

Riffel

Riffel Catena KB-819 Manual de usuario

Texi

Texi Hestia Manual de usuario

Maxwell

Maxwell MW-3010 Manual de usuario

TREVIDEA

TREVIDEA Girmi ST60 Manual de usuario

Philips

Philips HI5914/30 Manual de usuario

Primula

Primula Vapormat Manual de usuario

Magio

Magio MG-541 Manual de usuario

Scarlett

Scarlett SC-1334S Manual de usuario

Bosch

Bosch Sensixx B22L Manual de usuario

Philips

Philips GC651 Manual de usuario

Vitek

Vitek VT-1247 VT Manual de usuario

Cleanmaxx

Cleanmaxx 3397 Manual de usuario

Philips

Philips GC800 Manual de usuario