Morphy Richards IB42345 Manual de usuario

AquaMax steam station

Please read and keep these instructions

www.morphyrichards.com

getting the best from your

new steam station...

•Safety first

Caution must be used when handling this appliance as it does get

very hot. Always switch off the unit and allow to cool before

cleaning or storing.

• Anti-scale

Anti-scale cartridges are available from our Morphy Richards

service department please contact our replacement parts number

above.

42345 Rev 2 31/5/05 9:39 AM Page 1

Important safety

instructions

The use of any electrical appliance

requires the following common sense safety

rules.

Primarily there is danger of injury or

death and secondly the danger of damage

to the appliance. These are indicated in the

text by the following two conventions:

WARNING: Danger to the person!

IMPORTANT: Damage to the appliance! In

addition we offer the following safety

advice.

Location

•Do not use outdoors.

Children

•Close supervision is necessary when any

appliance is used near children.

Personal safety

•WARNING: Burns can occur from

touching hot metal parts, hot water

or steam.

•WARNING: To protect against the

risk of electric shock do not put the

appliance in water or in any other

liquid.

•Do not use the vertical steam feature on

clothes that are being worn.

•Do not leave the steam station

unattended whilst plugged in or on an

ironing board. Never allow the mains

cord to over hang the work surface.

•The socket should always be off before

plugging or unplugging from the socket.

Never yank the cord to disconnect from

the socket, instead, grasp plug and pull

to disconnect.

•Do not allow the cord to touch hot

surfaces. Let the steam station cool

completely before putting away.

Other safety considerations

•Use the steam station only for its

intended use.

•Always disconnect the steam station

from the electrical socket when filling

the tank and when not in use.

•Do not operate the steam station with a

damaged cord or if the steam station

has been dropped or damaged. To avoid

the risk of electric shock, do not

disassemble the steam station, but

telephone Morphy Richards for advice.

Incorrect reassembly can cause a risk of

electric shock when the steam station is

used.

Special instructions

•If your steam station does not work,

check the following points:

Has the temperature control been set to

the required temperature? Is the plug in

its socket? Is the plug itself or the

socket faulty? (Check by plugging in

another appliance).

•WARNING: When not in use, your

steam station should never be left

on an ironing board unattended.

•To prevent damage to the textile being

ironed, follow the temperature guide

carefully. (Test the inside of the hem of

the garment).

•When ironing is complete, remove the

plug from the socket and allow to cool

before storage.

•If you drop or severely knock your steam

station this could cause internal damage

even if the outside appears alright. Have

it checked by a qualified electrician.

•It is recommended that everytime the

steam station is used the steam button

is depressed away from the ironing

board for approximately 30 seconds.

This enables the iron to discharge any

droplets of water held in the system.

•This process should be applied if you

have not steam ironed for several

minutes.

42345 Rev 2 31/5/05 9:39 AM Page 2

Electrical

requirements

Check that the voltage on the rating

plate of your appliance corresponds with

your house electricity supply which must be

A.C. (Alternating current).

If the socket outlets in your home are

not suitable for the plug supplied with this

appliance the plug should be removed and

the appropriate one fitted.

WARNING : The plug removed from

the mains lead, if severed, must be

destroyed as a plug with a bared

flexible cord is hazardous if engaged

into a live socket outlet.

Should the fuse in the 13 amp plug

require changing a 13 amp BS1362 fuse

must be fitted.

WARNING: This appliance must be

earthed.

Instructions for use

Temperature guide

Heat setting markings on the adjustable control dial of all Morphy Richards irons match

those of the International Textile Care Labelling Code.

Symbol

(120˚C Max) Cool (160˚C Max) Warm (210˚C Max) Hot

Control knob

positions

Do not

iron at all

Fabric Nylon, Acetates

e.g. Acrilan

Courtelle, Orlon

Triacetates, e.g.

Tricel/Polyester

Wool, Polyester

mixtures e.g.

Polyester/Cotton

Cotton, Linen

Rayon, Rayon

mixtures,

e.g. Rayon/Linen

Ironing Iron on wrong side

if moisture required

use damp cloth

(Not Acetate)

Fabrics requiring this

setting usually require

steam pressing for heavy

cotton, denim etc.

With water in tank Dry Steam

Without water in tank Dry ironing

42345 Rev 2 31/5/05 9:39 AM Page 3

Components of your

steam station

⁄ Steam on/off button

¤ Filling cap

‹ Removable anti-scale

cartridge

› Anti-scale release button

ﬁ Water tank

ﬂPower cord

‡ Temperature dial with indicator

· Temperature indicator light

‚ Supply cord

„ Steam on/off indicator light

‰ Filling funnel

Before use

Note: The steam facility should only be

used on garments which are suitable for

ironing at the 3 dot setting.

Clothes can be steam ironed at the 2 dot

setting, but only for a short period.

Textiles and clothes are supposed to

carry ironing instructions. If they don’t you

should follow the fabric guide on page 3, but

be sure to test the temperature by ironing the

hem of the garment or similar area first.

If you turn the control dial down from a

hot setting to a cooler setting, wait until the

steam station temperature has stabilised

before you continue ironing.

Filling

1Make sure that the steam station is not

plugged in before filling the tank with

water.

2Lift up the fill cap ¤and fill the tank ﬁ

with water through the filling hole using

the funnel provided. A1.1 litres fills the

tank. After filling replace the fill cap. In

hard water areas the use of distilled or

demineralised water is recommended.

WARNING: Never use battery topping

up fluid or water containing any

substances like starch, or sugar, or

defrosted water from a refrigerator.

3Always pour out the remaining water if the

product is not to be used for a few

weeks. Water can be left in the unit

between normal ironing periods.

WARNING: When filling your steam

station with tap water always use the

funnel provided. Never fill directly under

the tap.

Temperature control

Plug in the steam station and switch on.

Set the temperature control dial on the iron

Bto the temperature required, but don’t

start ironing immediately.

⁄

‹›ﬁ

ﬂ

‡

‚

„

‰

42345 Rev 2 31/5/05 9:39 AM Page 4

If you wait a few minutes, the steam

station will stabilise at the required setting.

Your Morphy Richards iron is fitted with an

indicator light ·which will go on and off

while you are ironing.

This is perfectly normal as it shows that

the iron is maintaining the heat setting you

have chosen.

It is always a good idea to begin with

cool fabrics and work up to higher settings.

An iron heats up quicker than it cools

down so you’ll save time and electricity.

Features of your iron

Temperature indicator light

The indicator light shows that the iron is

warming up. When the required temperature

is reached the light will go out and will cycle

on-off during operation.

Dry ironing

You can use your steam station as a dry

iron only.

Any temperature setting may be used

depending on the garment. You do not

need to put any water in the tank when dry

ironing only.

'Click' on - 'click' off steam button

To activate the steam press the steam

button ⁄once and release. The indicator

light „will illuminate, indicating the iron is

in steam mode. The first time you use the

steam station, it will take approximately 30

seconds for the steam to start. Any noise

will be due to the pump removing air from

the system.

To stop the steam, press and release the

steam button ⁄again.

Note: When the tank needs re-filling with

water the pump will become noisy.

This is quite normal but the tank should

be immediately filled with water. Failure to

do so could damage the steam system.

Anti-scale system

The anti-scale cartridge is designed to

reduce build-up of limescale which occurs

during steam ironing, this will prolong the

working life of your steam station. However

please note that the anti-scale cartridge will

not completely stop the natural process of

limescale build-up.

Anti-scale cartridge replacement

1Press the release button to the side of

the cartridge. C

2Lift out the old unit and replace with a

new one.

3Press to lock in position.

How often you need to replace your

anti-scale cartridge depends on how often

you use your iron with its steam functions

and how ‘hard’ your water supply is. Water

hardness varies greatly from one area to

another. For advice on the relative hardness

of your water, contact your local water

supplier.

However, please note that the anti-scale

cartridge will not completely stop the

natural process of limescale build-up. If in

average you spend 2 hours per week

ironing, then we suggest you replace your

anti-scale cartridge as shown in the table

below. If you iron more or less frequently

then you should alter the interval between

re-fills accordingly.

Water hardness Soft Medium Hard

Refill interval 6 3 11/2

(months)

42345 Rev 2 31/5/05 9:39 AM Page 5

Emptying and storing

When you have finished ironing, unplug

your steam station. Ensure that the steam

control is set to the 'OFF' position.

Do not store in the box, place the iron

onto the steam station base and allow to

cool before storage.

Maintenance

WARNING: Do not attempt to descale

the steam station with descaling

products.

To clean a stainless steel soleplate

To keep the soleplate of your steam

station clean and free of limescale, we

recommend that you use one of the gentle

chrome, silver or stainless steel cleaners that

are generally available. Always follow the

manufacturers instructions. To clean off

melted man-made fibres set the steam

station at 3 dot position and pass it over a

clean piece of cotton which will draw the

deposit off the surface.

To clean the exterior

Allow the steam station to cool and wipe

the iron and base unit with a damp cloth and

mild detergent, then wipe with a dry cloth.

Helpline

If you have any difficulty with your

appliance, do not hesitate to call us.

We are more likely able to help than the

store from where you bought it.

Please have the following information

ready to enable our staff to deal with your

query quickly.

•Name of the product

•Model number as shown on the underside

of the appliance.

42345 Rev 2 31/5/05 9:39 AM Page 6

Your two year guarantee

It is important to retain the retailers

receipt as proof of purchase. Staple your

receipt to this back cover for future

reference.

Please quote the following information if

the product develops a fault. These numbers

can be found on the base of the product.

Model no. Serial no.

All Morphy Richards products are

individually tested before leaving the factory.

In the unlikely event of any appliance proving

to be faulty within 28 days of purchase it

should be returned to the place of purchase

for it to be replaced.

If the fault develops after 28 days and

within 24 months of original purchase, you

should contact the Helpline number quoting

Model number and Serial number on the

product, or write to Morphy Richards at the

address shown. You will be asked to return

the product (in secure, adequate packaging)

to the address below along with a copy of

proof of purchase.

Subject to the exclusions set out below

(see Exclusions) the faulty appliance will then

be repaired or replaced and dispatched

usually within 7 working days of receipt.

If for any reason this item is replaced

during the 2 year guarantee period, the

guarantee on the new item will be calculated

from original purchase date. Therefore it is

vital to retain your original till receipt or

invoice to indicate the date of initial

purchase.

To qualify for the 2 year guarantee the

appliance must have been used according to

the manufacturers instructions.

EXCLUSIONS

Morphy Richards shall not be liable to

replace or repair the goods under the terms

of the guarantee where:

1The fault has been caused or is

attributable to accidental use, misuse,

negligent use or used contrary to the

manufacturers recommendations or where

the fault has been caused by power

surges or damage caused in transit.

2The appliance has been used on a voltage

supply other than that stamped on the

products.

3Repairs have been attempted by persons

other than our service staff (or authorised

dealer).

4Where the appliance has been used for

hire purposes or non domestic use.

5Morphy Richards are not liable to carry

out any type of servicing work, under the

guarantee.

6Anti-scale cartridges for all Morphy

Richards irons, steam generators are not

covered by the guarantee.

This guarantee does not confer any rights

other than those expressly set out above and

does not cover any claims for consequential

loss or damage. This guarantee is offered as

an additional benefit and does not affect your

statutory rights as a consumer.

•This guarantee is valid in the UK and

Ireland only.

42345 Rev 2 31/5/05 9:39 AM Page 7

Morphy Richards products are intended for

household use only.

Morphy Richards has a policy of continuous

improvement in product quality and design.

The company, therefore reserves the right

to change the specification of its models at

any time.

The After Sales Division

Morphy Richards Ltd, Mexborough

South Yorkshire, England, S64 8AJ

Helpline (office hours)

UK 0870 060 2615

Republic of Ireland 1800 409119

RN42345M UK Rev 2 03/05

42345 Rev 2 31/5/05 9:39 AM Page 8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hierro de Morphy Richards

Morphy Richards

Morphy Richards Comfigrip Advanced 40715 Manual de usuario

Morphy Richards

Morphy Richards TURBOSTEAM RN40630 MUK REV2 Manual de usuario

Morphy Richards

Morphy Richards JET STREAM Manual de usuario

Morphy Richards

Morphy Richards Turbo steam iron Manual de usuario

Morphy Richards

Morphy Richards breeze Manual de usuario

Morphy Richards

Morphy Richards ELITE S Manual de usuario

Morphy Richards

Morphy Richards IB40622 Manual de usuario

Morphy Richards

Morphy Richards TURBOSTEAM RN40513 Manual de usuario

Morphy Richards

Morphy Richards Turbosteam Manual de usuario

Morphy Richards

Morphy Richards IB42700 Manual de usuario

Morphy Richards

Morphy Richards 40850 COMFIGRIP IRON Manual de usuario

Morphy Richards

Morphy Richards Breeze 40310 Manual de usuario

Morphy Richards

Morphy Richards Saturn IntelliTemp 305003 Manual de usuario

Morphy Richards

Morphy Richards Precise Steam Iron steam/spray shot Manual de usuario

Morphy Richards

Morphy Richards POWER STEAMELITE Manual de usuario

Morphy Richards

Morphy Richards TURBOSTEAM 40659 Manual de usuario

Morphy Richards

Morphy Richards IB40620 Manual de usuario

Morphy Richards

Morphy Richards Steam Generator Manual

Morphy Richards

Morphy Richards IB4050X Manual de usuario

Morphy Richards

Morphy Richards SPEED STEAMPRO Manual de usuario

Morphy Richards

Morphy Richards Turbosteam Manual de usuario

Morphy Richards

Morphy Richards 40707 Manual de usuario

Morphy Richards

Morphy Richards RN40655 Manual de usuario

Morphy Richards

Morphy Richards IB40460 Manual de usuario

Manuales populares de Hierro de otras marcas

Clatronic

Clatronic DB 3703 Manual de usuario

TEFAL

TEFAL FV4093Z0 Manual de usuario

Gorenje

Gorenje SIH 2200 BS Manual de usuario

Philips

Philips GC6012 Manual de usuario

Bosch

Bosch 2 Series Manual de usuario

Riffel

Riffel Catena KB-819 Manual de usuario

Texi

Texi Hestia Manual de usuario

Maxwell

Maxwell MW-3010 Manual de usuario

TREVIDEA

TREVIDEA Girmi ST60 Manual de usuario

Philips

Philips HI5914/30 Manual de usuario

Primula

Primula Vapormat Manual de usuario

Magio

Magio MG-541 Manual de usuario

Scarlett

Scarlett SC-1334S Manual de usuario

Bosch

Bosch Sensixx B22L Manual de usuario

Philips

Philips GC651 Manual de usuario

Vitek

Vitek VT-1247 VT Manual de usuario

Cleanmaxx

Cleanmaxx 3397 Manual de usuario

Philips

Philips GC800 Manual de usuario