Monoprice MP Mibi Delta Manual de usuario

MONOPRICE

MP Mini Delta 3D Printer

P/N 21666

User's Manual

CONTENTS

SAFETY WARNINGS AND GUIDELINES.......................................................................................................................................3

INTRODUCTION................................................................................................................................................................................................4

FEATURES..............................................................................................................................................................................................................4

CUSTOMER SERVICE....................................................................................................................................................................................5

PACKAGE CONTENTS.................................................................................................................................................................................5

PRODUCT OVERVIEW.................................................................................................................................................................................6

USING THE MENU SYSTEM....................................................................................................................................................................6

USING THE QUICK ACCESS LED BUTTON ................................................................................................................................. 7

PRINTER SETUP.................................................................................................................................................................................................8

COMPLETED PRINT REMOVAL .........................................................................................................................................................10

WI-FI SETUP.......................................................................................................................................................................................................10

SOFTWARE INSTALLATION AND SETUP...................................................................................................................................11

Installing Cura for Windows®......................................................................................................................................................12

Repetier-Host............................................................................................................................................................................................19

TECHNICAL SUPPORT...............................................................................................................................................................................21

REGULATORY COMPLIANCE..............................................................................................................................................................21

Notice for FCC ..........................................................................................................................................................................................21

Notice for Industry Canada...........................................................................................................................................................21

SAFETY WARNINGS AND GUIDELINES

Do not remove the insulating tape on the heater block, which is directly above the

nozzle.

Take care to avoid touching hot parts, including heat blocks, extruder nozzle,

extruded filament, and the heated bed.

Do not wear gloves when operating or repairing to avoid entanglement.

Keep the printer and all accessories out of reach of children.

Do not remove or disconnect the USB cable when printing from a computer.

Do not pull or twist the black cable at any time.

Do not force or tear anything when unpacking and during setup. This may cause

damage to the printer and/or its accessories.

Do not reach inside the printer during operation.

Always allow the printer and extruded filament to cool before reaching inside.

Ensure that the printer is turned off and unplugged from its power source before

making repairs or performing service.

Do not install this device on an unstable surface where it could fall and cause either

personal injury or damage to the device and/or other equipment.

Do not subject the product to extreme force, shock, or fluctuations in temperature

or humidity.

This device is intended for indoor use only.

Do not expose this device to water or moisture of any kind. Do not place drinks or

other containers with moisture on or near the device. If moisture does get in or on

the device, immediately unplug it from the power outlet and allow it to fully dry

before reapplying power.

Do not touch the device, the power cord, or any other connected cables with wet

hands.

Use only in a well-ventilated area. Do not use in close, confined spaces.

Prior to operation, check the unit and power cord for physical damage. Do not use if

physical damage has occurred.

Before plugging the unit into a power outlet, ensure that the outlet provides the

same type and level of power required by the device.

Unplug this device from the power source when not in use.

Take care to prevent damage to the power cord. Do not allow it to become

crimped, pinched, walked on, or become tangled with other cords. Ensure that the

power cord does not present a tripping hazard.

Never unplug the unit by pulling on the power cord. Always grasp the connector

head or adapter body.

INTRODUCTION

Thank you for purchasing this MP Mini Delta 3D printer from Monoprice! This printer

features a single extruder, which is capable of printing in PLA, ABS, and other materials.

You can print from a Windows® or Mac® PC using a USB connection or can print from 3D

model files stored on a microSD™card, without the need for a PC connection of any kind.

This printer is easy to setup and easy to use following the instructions in this manual.

FEATURES

Single extrusion print head

Can print PLA, ABS, and other materials

Open frame design for ease of use and maintenance

USB, microSD™, and Wi-Fi® connectivity options

Free WiFi Connect app available from the Google Play™ store or from iTunes®

Includes 256MB microSD card with Cura, Repetier-Host, and a sample 3D model

(auto00.g)

One-button printing of any file named auto00.g on an installed microSD card

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering,

purchasing, and delivery experience is second to none. If you have any problem with your

order, please give us an opportunity to make it right. You can contact a Monoprice

Customer Service representative through the Live Chat link on our website

www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-

6pm PT) or via email at [email protected]

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have all the items listed

below. If anything is missing or damaged, please contact Monoprice Customer Service for a

replacement.

1x MP Mini Delta 3D printer

1x Filament holder

1x Plastic scraper

1x USB cable

1x MicroSD™card

3x Hex wrench

1x Power adapter

1x AC power cord (NEMA 5-15 to

IEC 60320 C13)

PRODUCT OVERVIEW

1. Extruder

2. Nozzle

3. Micro USB Port

4. DC Power Connector

5. Quick Access LED Button

6. MicroSD™ Card Slot

7. Filament Holder Slots

USING THE MENU SYSTEM

The menu system is displayed on a lighted LCD screen.

The menu selection highlight or pointer is moved by pressing the top and bottom

buttons to the right of the display.

Press the top button to move the highlight/pointer to the left and up.

Press the bottom button to move the highlight/pointer to the right and down.

Press the top button while editing a value to increase that value.

Press the bottom button while editing a value to decrease that value.

Press the center button to activate the selected menu item or to save an edited

value.

USING THE QUICK ACCESS LED BUTTON

The Quick Access LED Button (5) is located between the USB port and microSD™ card slot.

Ensure that the included microSD card is inserted into the MicroSD Card Slot (6)

prior to using the Quick Access LED Button (5).

Press the Quick Access LED Button (5) to automatically start printing the auto00.g

sample model file on the included microSD card (formerly cat.gcode). The LED inside

the button will blink green three times, then will remain illuminated green while

printing is in progress. Note that any file named auto00.g will print automatically

when the Quick Access LED Button (5) is pressed.

Press the Quick Access LED Button (5) while printing is in progress to pause printing.

Printing may continue for 5-10 seconds before it becomes paused. The LED inside

the button will extinguish when the print task is paused and will remain

extinguished until printing is resumed.

Press the Quick Access LED Button (5) while a print task is paused to resume

printing.

Press and hold the Quick Access LED Button (5) for 4 seconds while printing is in

progress to cancel the print task. The LED inside the button will extinguish when the

print task is cancelled.

While the printer is idle, press and hold the Quick Access LED Button (5) for 4

seconds to initialize the built-in Wi-Fi® Smart Config function for use with the free

MP 3D Printer WiFi Connect app from the Google Play™ store or from iTunes®. The

LED inside the button will blink blue three times, then will extinguish. The Wi-Fi

Smart Config function will remain active until the button is pressed again or the

printer is powered off.

PRINTER SETUP

Warning! Take care not to remove or damage the black PEI build mat on the build platform.

This mat is essential to ensure the 3D model properly adheres to the build platform during

printing. If this mat becomes damaged or wears out, replace it with painter's tape, Kapton®

tape, or ordinary masking tape.

Perform the following steps to prepare the printer for use.

1. Remove the printer from its packaging and place it on a flat, stable surface with

plenty of ventilation and a nearby AC power outlet.

2. Open the Accessories box and remove the Filament Holder. Slide

the tab at the flat end into the Filament Holder Slots (7) on the

rear of the printer frame.

3. Insert the included microSD™card into the MicroSD Card Slot (6)

on the side of the printer.

4. Plug the DC barrel connector on the included AC power adapter into the power

connector on the side of the printer. Next, plug the C13 end of the included AC

Power Cable into the C14 panel connector on the AC Power Adapter, then plug the

other end into a nearby AC power outlet.

5. Press the bottom button once to highlight the Temperature entry, then press the

center button to select it.

6. Press the center button to select the Nozzle (2) temperature value, then use the top

and bottom buttons to set the target temperature. Set it to 230°C for ABS filament

or set it to 190°C for PLA filament. Press the center button to save the target

temperature and begin heating the extruder.

7. While the printer is heating, open your filament. Using a pair of scissors or side

cutters, diagonally snip the end of the filament to make a point, as shown in the

images below. Place the spool on the Filament Holder.

8. Once the target temperature is reached, press the bottom button three times to

select the Exit option, then press the center button to return to the previous menu

page.

9. Press the bottom button to highlight the Move option, then press the center

button to enter the Move menu.

10. The Extruder option should be highlighted. Press the center button to select it.

11. While squeezing the lever on the Extruder (1), insert the filament

and push it into the opening. Keep pushing until you feel

resistance, then release the lever.

12. Press the top button to feed filament into the printer. Allow the

motor to run until it stops feeding. Repeat this process until

filament starts to extrude out of the Nozzle (2).

13. Using the included plastic scraper, clean the filament from the nozzle and bed.

14. Press the center button to deselect the Extruder entry.

15. Press the bottom button twice to highlight the Exit entry, then press the center

button to return to the previous menu.

16. Press the top button twice to highlight the Print option, then press the center

button. The printer will read the microSD™card and display the contents on screen.

17. Use the top and bottom buttons to highlight the auto00.g file (formerly cat.gcode),

then press the center button to start printing the model.

Congratulations, your 3D printer is setup and you are printing your first model!

COMPLETED PRINT REMOVAL

Perform the following steps to remove a completed print.

1. Wait until the heated bed has cooled to room temperature.

2. Using the included Plastic Scraper, try to wedge it under the print.

3. Continue pushing until the print begins to lift off the bed, try to push the scraper

further under the print.

4. If you encounter difficulty pushing the scraper under the print, try approaching it

from another side or try working the scraper around the perimeter of the print.

Continue pushing until you can slide the scraper all the way under the print, then lift

the printed model off the bed surface.

WI-FI SETUP

You can connect the printer wirelessly to a 2.4Ghz Wi-Fi® network to print models from

your Android™ or iOS® phone or tablet. Perform the following steps to setup the Wi-Fi

connection for your device.

1. Download and install the free MP 3D Printer WiFi Connect app from the Google

Play™store or from iTunes®, depending on which type of mobile device you have.

2. Disconnect the USB cable from the printer. You cannot use USB and Wi-Fi

connections at the same time.

3. Power on the printer.

4. Start the MP 3D Printer WiFi Connect app on your mobile device.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora 3D de Monoprice

Monoprice

Monoprice 13860 Manual de usuario

Monoprice

Monoprice MP Voxel Manual de usuario

Monoprice

Monoprice extrusion i3 13860 Manual de usuario

Monoprice

Monoprice MP Delta Pro Manual de usuario

Monoprice

Monoprice Maker Ultimate 2 Manual de usuario

Monoprice

Monoprice MP Mini Delta V2 Manual de usuario

Monoprice

Monoprice 30526 Manual de usuario

Monoprice

Monoprice cadet Manual de instrucciones

Monoprice

Monoprice Delta Pro Manual de usuario

Monoprice

Monoprice Voxel 33820 Manual de usuario

Monoprice

Monoprice 30994 Manual de usuario

Monoprice

Monoprice MP10 Manual de usuario

Monoprice

Monoprice Maker Ultimate 2 Manual de usuario

Monoprice

Monoprice MP Maker Pro Mk.1 Manual de usuario

Monoprice

Monoprice 15365 Manual de usuario

Monoprice

Monoprice Select Mini Pro Manual de usuario

Monoprice

Monoprice 15710 Manual de usuario

Monoprice

Monoprice MP Mini SLA LCD Manual de usuario

Monoprice

Monoprice MP CADET Manual de usuario

Monoprice

Monoprice 35435 Manual de usuario

Monoprice

Monoprice MP Voxel Pro Manual de instrucciones

Monoprice

Monoprice MP Mini Delta V2 Manual de usuario

Monoprice

Monoprice MP Education Guider II Manual de usuario

Monoprice

Monoprice 34438 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario