Molex 63825-6070 Manual de usuario

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 1 of 8

Revision: A Revision Date: 4-26-13

INSULATION CRIMP

▲SEE NOTE

BRUSH

STRIP LENGTH

BEL

L MOUTH

CUT

OFF

TAB

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP HEIGHT

TWISTING

SEAM

WIRE

Application Toolin

Specification Sheet

Tool Kit

Order No. 63825-6070

Hand Crimp Tool

Order No. 63825-6000

FEATURES

% A full cycle ratcheting hand tool ensures complete crimps

% Ergonomically designed soft handles

% Precisely designed crimping profiles with simple contact positioning

% Easy handling due to outstanding force ratio

 Tool kits are easily installed into the Hand Crimp Tool or the 63816- 3 Power Crimp Head which is installed

into the 63816- 2 (11 V) or the 63816- 25 (22 V) Battery Powered Tool.

 Many different Tool kits can be used with a single Battery Powered Tool.

 This tool is IPC/WHMA-A-62 Class 2 and RoHS compliant.

SCOPE

Products: CSP 6.3 Receptacle Terminal, 3mm², 2mm² (double), and 5mm² metric wire.

Terminal Series No.

Terminal Order No.

Wire Size

Insulation Diameter

Strip Len th



Reel Form Only

Wire Style

mm²

In.

98891 98891-1 13 T3 ZHID

–

3.2

.118

–

.126

5. – 5.5 .2 – .22

–

2.5

. 9

–

. 98

5 3.7 – 3.9 .146 – .154



Customer to cut off terminal from reel: .

mm (.

”) maximum Cut

off Tab.

DEFINITION OF TERMS

TYPE 4C

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 2 of 8

Revision: A Revision Date: 4-26-13

▲Insulation Crimp Note:

Due to the terminal’s insulation grip design

and/or insulation diameter range, this tool

uses “overlap” form geometry in the

insulation punch for the 3mm² and 5mm²

wires. This produces an overlap insulation

crimp (A62 – compliant). While the

insulation punch profile may appear

“lopsided”, this is a normal condition for this

tool. See figure to the right.

The 2 x 2mm² insulation crimp punch uses

the standard “B” crimp.

CONDITIONS:

After crimping, the conductor profiles should measure the following (see notes below).

Terminal Series No.

Bell mouth

Conductor Brush

Bend Up

Bend Down

Twist

Roll

De ree

(Max)

De ree

(Max)

9889

–

. 16

–

. 24

–

1.8

. 8

–

. 7

Terminal Series No.

Wire Size

Con

ductor Crimp

Profile

Hei ht

Width

98891

1.87

–

1.93

. 74

–

. 76

3.6 – 3.7

.142 – .146

2. 7

–

2.13

. 81

–

. 84

2.27

–

2.33

. 89

–

. 92

Terminal Series No.

Wire Size

Insulation Crimp

Pull Force

Minimum

Hei ht

Maximum

Width

Maximum

Lb.

98891

.157

.185

2 x 2

.157

.212

4.1

.161

5.2

.2 5

Tool Qualification Notes:

1. Pull force should be measured with no influence from the insulation crimp.

2. Pull force on the 2 x 2mm² crimp is based on pulling one wire.

3. The above specifications are guidelines to an optimum crimp.

Note:

A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,

insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,

destructive, pull force test should be preformed to check hand tool crimp. Pull Force value must exceed the

minimum pull force specifications listed.

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage

can occur to the tool or die.

OVERLAP

INSULATION

CRIMP

OVERLAP FORM GEOMETRY

ANVIL

PUNCH

WIRE

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 3 of 8

Revision: A Revision Date: 4-26-13

ANVILS

POWER

CRIMP

HEAD

Fi ure

PUNCHES

M4 X 10 LONG

BHCS

M4 X 18 LONG

BHCS

SWING

LOCATOR

OPEN

PRESS DOWN

ON THE BRASS

PIVOT SHAFT

LIFT UP ON

THE LOCATOR

Fi ure

Fi ure 4

SWING OPEN

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

LOCATOR

TERMINAL

IN PLACE

LOCATOR LATCH

IN OPEN POSITION

INSTALLATION

To install the Tool Kit into the Power Crimp Head follow the steps below:

Anvils and Punches Installation

1. Insert the Anvils into the bottom slots of the nest. Install the M4 x 1 long BHCS and tighten in place.

2. Insert the Punches into the top slots of the nest. Install the M4 x 18 long BHCS and tighten in place. See

Figure 1.

Locator Installation and Removal

Follow the steps below to install or replace the locator. See Figure 2.

To install the locator

1. Position the locator with the hole over the brass pivot shaft and snap it into place.

To remove the locator

1. Open the crimp hand tool.

2. Swing the existing locator open and away from the hand tool.

3. Firmly press down on the

brass pivot shaft with your

thumb, while pulling the

locator up. Slip the locator

off the top of the brass pivot

shaft.

OPERATION

Open the tool by squeezing the

handles together, at the end of

the closing stroke, the ratchet

mechanism will release the

handles, and the hand tool will

spring open.

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 4 of 8

Revision: A Revision Date: 4-26-13

Fi ure 6

WIRE IN TERMINAL

JAWS

PARTIALLY

CLOSED

WIRE AGAINST

WIRE STOP

HANDLE

OPEN

LOCATOR

CLOSED

Fi ure 5

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

Crimpin Terminals

1. Select the desired terminal listed in the preceding charts.

2. Turn the Locator Lock Latch down to unlock. See Figure 3.

3. Swing the terminal locator away from the crimp tool shown in Figure 4. Some terminals with large insulation

grips may interfere with the crimp tooling when swinging the locator into position. The terminal must then be

loaded into the locator in the closed/crimp

position. See Figure 5.

4. Press down on the wire stop on the locator as

shown in Figure1. Insert the proper terminal

into the proper nest opening. Make sure when

choosing the nest opening, it will correspond

with the A, B or C profile on the hand tool.

5. Return the locator to its original position.

6. Turn the Locator Lock Latch up to lock. Make

sure that the terminal is visually centered over

the punch.

7. Insert the proper wire over the terminal.

8. Gently touch the wire stop with the end of the

wire. See Figure 6 and 7.

9. Compress the terminal by squeezing the tool

handles until the ratchet mechanism cycle has

been completed. Release handles to open the

jaws.

1 . Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on

the wire. The terminal locator can be in either position.

11. Visually inspect the crimped terminal for proper crimp location.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

For the Battery Power Tool:

1. Cycle the Battery Power Tool to crimp the terminal to the wire.

2. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on

the wire. The terminal locator can be in either position.

3. Visually inspect the crimped terminal for proper crimp location.

Fi ure 7

WIRE

INSULATION

PUNCH

CONDUCTOR ANVIL

LOCATOR

INSULATION

ANVIL

WIRES AGAINST

LOCATOR STOP

CONDUCTOR

PUNCH

TERMINAL

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 5 of 8

Revision: A Revision Date: 4-26-13

Maintenance

It is recommended that each operator of the tool

be made aware of, and responsible for, the

following maintenance steps:

1. Remove dust, moisture and other

contaminants with a clean brush, or soft, lint-

free cloth.

2. Do not use any abrasive materials that could

damage the tool.

3. Make certain all pins; pivot points and

bearing surfaces in the tool head are

protected with a thin coat of high quality

machine oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of

equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping. The use of

light oil, such as 3 weight automotive oil, every 5, crimps or monthly, will significantly enhance the tool life

and ensure a stable calibration. See Figure 8A or 8B for lubrication points.

4. Store the tool in a clean and dry area when not in use.

Miscrimps or Jams for Crimp Hand Tools Only (See Fi ure 11)

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by rotating the small slotted screw marked with an arrow. See Figure 11.

Warranty

This tool kit is for electrical terminal crimping purposes only. This tool kit is made of the best quality materials. All

vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 3

days. Should such a defect occur, we will repair or exchange the tool kit free of charge. This repair or exchange

will not be applicable to altered, misused, or damaged tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

CAUTION: Repetitive use of this tool should be avoided.

Certification

Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for

customers to re-certify hand tools.

LUBRICATION

POINTS

(BOTH SIDES)

LIGHT OIL

(EVERY MONTH

5,000 CRIMPS)

Fi ure8A

Fi ure 8B

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 6 of 8

Revision: A Revision Date: 4-26-13

% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped

12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

25mm (1. ”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and

replaced.

% This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.

The chart below shows all applications for this Tool Kit.

Tool Kit

Order No. Tool Order No.

Tool Description

Power

Head

Order No.

Ada

pter

Description Fi ure No.

63825-6 7

6381

1 5

Hand Crimp Frame (Short)

N/A

6381

Hand Crimp Frame (Long)

N/A

63816

Battery Power

Tool (11 V)

63816

Power Crimp Head

63816

Battery Power

Tool (22 V)

63816

ower Crimp Head

Applications for the Tool Kit

Hand Crimp Tool

Battery Powered Tool

Fi ure

WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper

instruction and without first reading and understanding the instructions in the proper Manual or

Specification Sheet. See Chart above for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the

power is turned off.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

POWER

CRIMP

HEAD

LOCKING PINS

BATTERY

POWERED

TOOL

TOOLING KIT

HAND CRIMP

FRAME LONG

AND SHORT

TOOLING KIT

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 7 of 8

Revision: A Revision Date: 4-26-13

RATCHET

RELEASE SCREW

Fi ure 11

M4 X 8mm

LONG BHCS

M4 X 18mm

LONG BHCS

M4 X 10mm

LONG BHCS

WITH TOOL KIT

LOCATOR ONLY

HAND TOOL PARTS LIST

Item Number

Order Number

Description

Quantity

6381

Hand Crimp Frame (Long)

6382

Tool Kit with

Locator

638

Locator Base

6382

Locator (only)

Hand Crimp Tool for CSP 6.3 Receptacle Terminal

Doc No: ATS-638256 HM Release Date: 4-26-13 UNCONTROLLED COPY Page 8 of 8

Revision: A Revision Date: 4-26-13

Fi ure 12

Lon

BHCS

Lon

BHCS

Lon

BHCS

POWER HEAD PARTS LIST

Item

rder No

En ineerin No.

Description

Quantity

63816- 3 63816- 3 Power Crimp Head 1

63825-6 7 63825-577 Tool Kit 1

Visit our Web site at http://www.molex.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 64005-6400 Manual de usuario

molex

molex 11-01-0101 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63828-0600 Manual de usuario

molex

molex 63811-9370 Manual de usuario

molex

molex CR5905 Manual de usuario

molex

molex 4D Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex ServiceGrade Guía del usuario

molex

molex 98897 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63825-5800 Guía del usuario

molex

molex AT-200 Manual

molex

molex 2002180370 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex ServiceGrade 64016-0038 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex AT-200 Manual

molex

molex 63816-1000 Manual de usuario

molex

molex 63825-9570 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63825-9900 Manual de usuario

molex

molex 63823-5200 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex 63825-6070 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas