molex 207129 Series Manual de usuario
Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle
oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 1 of 6
Revision: A Revision ate: 06-06-11
TYPE 4A
INSULATION CRIMP
▲SEE NOTE
BRUSH
STRIP LENGTH
TERMINAL
STRIP
CONDUCTOR
CRIMP HEIGHT
CUT-OFF TAB
SEAM
BELL MOUTH
WIRE
CUT-OFF TAB
Applicatio Tooli g
Specificatio Sheet
Modular Crimp Head
Order No. 63823-8570
Ha d Crimp Tool
Order No. 63823-8500
FEATURES
% A full cycle ratcheting hand tool ensures complete crimps
% Ergonomically designed soft handles
% Precisely designed crimping profiles with simple contact positioning
% Easy handling due to outstanding force ratio
% Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63816-0100,
accompanied by Air Powered Crimp Adapter (Order No. 63816-0700).
% Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V),
accompanied by Battery Powered Crimp Adapter (Order No. 63816-0600).
SCOPE
Products: 2.79mm (.110”) Slip-On Quick isconnect Receptacle, for 16-20 AWG.
Termi al Series No.
Termi al Order No.
Wire Size I sulatio Diameter Strip Le gth
Reel Form O ly
AWG
mm²
mm I . mm I .
35711 35711-0700
35711-0710
16 1.31
1.80-2.30
.070-.091
4.50-5.00
.177-.197
18 0.80
20 0.52
Customer to cut off terminal from reel: 0.20mm (.008”) maximum Cut-off Tab.
See crimp specification for the individual Insulation iameter.
DEFINITION OF TERMS
Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle
oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 2 of 6
Revision: A Revision ate: 06-06-11
WIRE
INSULATION
PUNCH
TERMINAL
WIRE STOP BLADE
Figure 1
▲I sulatio Crimp Note:
ue to the terminal’s insulation grip design and/or
insulation diameter range, this tool uses “overlap” form
geometry in the insulation punch. This produces an
overlap insulation crimp (A620 – compliant). While the
insulation punch profile may appear “lopsided”, this is a
normal condition for this tool. See figure to the right.
(Some tools with multiple crimp pockets may not have
the “overlap” profile on all pockets).
CRIMP SPECIFICATIONS:
After crimping, the crimp profiles should measure the following.
Termi al Series No.
Wire Size Co ductor Crimp Profile
Height Width
AWG
mm²
mm I . mm
I . 16
18
20
35711
16 1.31 1.35-1.45
.053-.057
2.00
.079
X
18 0.80 1.15-1.25
.045-.049
2.00
.079
X
20 0.52 1.00-1.12
.039-.044
2.00
.079
X
Termi al
Series No.
Wire Size I sulatio Crimp Pull Force Mi imum
Height (Ref)
Width (Ref)
AWG
mm²
mm I . mm I . N Lb.
35711
16 1.31 2.75 .108 3.10 .122
130.43 29.32
18 0.80 2.70 .106 2.95 .116
83.36 18.74
20 0.52 2.35 .093 2.95 .116
59.82 13.45
■Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
OPERATION
Open the tool by squeezing the handles together, at the end of the
closing stroke, the ratchet mechanism will release the handles, and
the hand tool will spring open.
Crimpi g Termi als
1. Lift the wire stop blade up.
2. Insert the terminal fully into the correct profile until the terminal
is fully seated and stops.
3. Bring down the wire stop blade.
4. Slide the pre-stripped wire into the wire stop blade. See Figure
1. Be sure to hold the wire in place until the terminal is fully
crimped. See Figure 2.
5. Close the tool until the ratchet releases, the tool handles will then spring open.
6. Lift the wire stop blade up if it is still in down position.
7. Carefully remove the crimped terminal.
OVERLAP
INSULATION
CRIMP
OVERLAP FORM GEOMETRY
ANVIL
PUNCH
WIRE
Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle
oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 3 of 6
Revision: A Revision ate: 06-06-11
Figure 2
WIRE
TERMINAL
LOCATOR
INSULATION
PUNCH
INSULATION
ANVIL
WIRE STOP
BLADE
CONDUCTOR
ANVIL
CONDUCTOR
PUNCH
Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
Mai te a ce
It is recommended that each operator of the tool be made
aware of, and responsible for, the following maintenance steps:
1. Remove dust, moisture, and other contaminants with a
clean brush, or soft, lint free cloth.
2. o not use any abrasive materials that could damage the
tool.
3. Make certain all pins; pivot points and bearing surfaces are
protected with a thin coat of high quality machine oil. o
not oil excessively. The tool was engineered for durability
but like any other equipment it needs cleaning and
lubrication for a maximum service life of trouble free
crimping. Light oil (such as 30 weight automotive oil) used
at the oil points, every 5,000 crimps or 3 months, will
significantly enhance the tool life.
4. Wipe excess oil from hand tool, particularly from crimping
area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics
of an application.
5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,
and store the tool in a clean, dry area.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or
closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.
Warra ty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will
not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,
fixturing, or use of handle extensions voids this warranty.
CAUTION: Repetitive use of this tool should be avoided.
CAUTIONS:
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle
oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 4 of 6
Revision: A Revision ate: 06-06-11
Notes:
1. This tool should only be used for the terminals and wire gauges specified on this sheet.
2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above).
Variations in tools, terminals, wire stranding, and insulation types may affect crimp height.
3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all
insulation sizes.
4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts
available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.
5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no
influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips
on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping
Handbook 63800-0029 for additional information on crimping and crimp testing.
6. Molex does not certify crimp hand tools.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
Applicatio s for the Modular Crimp Head
WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction
and without first reading and understanding the instructions in the proper Manual or Specification Sheet.
See Chart below for the correct Manual or Specification Sheet.
WARNING: NEVER install tooling or service this tool while it is into any power source. isconnect the
power by unplugging or turn off the Actuator from its power source.
CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.
CAUTION: Wear safety glasses when operating or serving this tool.
Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle
oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 5 of 6
Revision: A Revision ate: 06-06-11
MODULAR
CRIMP
HEAD
BATTERY
POWER
CRIMP
ADAPTER
LOCKING
PINS
LOCKING PINS
BATTERY
POWERED
TOOL
AIR
POWER
TOOL
MODULAR
CRIMP HEAD
LOCKING
PINS
LOCKING
PINS
AIR
POWER
CRIMP
ADAPTER
The chart below shows all applications for this Modular Crimp Head.
Modular Crimp Head
Order No.
Tool
Order o.
Tool
Descriptio
Adapter
Order No.
Adapter
Descriptio
Figure
No.
63823-8570
63816-0000
Hand Crimp Frame (Short) N/A N/A 3
63816-0050
Hand Crimp Frame (Long) N/A N/A 3
63816-0200
Battery Power Tool (110 V)
63816-0600
Battery Power Crimp Adapter
4
63816-0250
Battery Power Tool (220 V)
63816-0600
Battery Power Crimp Adapter
4
63816-0100
Air Power Tool 63816-0700
Air Power Crimp Adapter 5
Applicatio s for the Modular Crimp Head
Ha d Crimp Tool Battery Powered Tool Air Powered Tool
Figure 3 Figure 4 Figure 5
MODULAR
CRIMP
HEAD
LOCKING
PINS
HAND CRIMP
FRAME LONG
OR SHORT
Hand Crimp Tool: for 2.79mm (.110”) Slip-On Quick isconnect Receptacle
oc No: ATS-6382385HM Release ate: 06-06-11 UNCONTROLLED COPY Page 6 of 6
Revision: A Revision ate: 06-06-11
RATCHET
RELEASE LEVER
HANDLE
SPRING
CRIMPING
SPRING (2)
3
6
4
Figure 6
2
5
1
M4 X 14mm
LONG BHCS
PARTS LIST
Ha d Crimp Tool 63823-8500
Item
Order Number
Descriptio Qua tity
1 63823-8570 Modular Crimp Head 1
2 63816-0050 Hand Crimp Frame (Long)
1
3 63823-8575 Locator 1
4 63816-0001 Locking Pin 2
5 63600-0525 Handle Spring 1
6 63600-0520 Crimping Spring 2
http://www.molex.com
Otros manuales para 207129 Series
100
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Herramientas de crimpado de molex
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 59354 Manual de usuario
molex
molex 63825-7570 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63811-5300 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63827-8200 Manual de usuario
molex
molex 63825-4800 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63825-5800 Guía del usuario
molex
molex CR60930B Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63827-6070 Manual de usuario
molex
molex 63823-6370 Manual de usuario
Manuales populares de Herramientas de crimpado de otras marcas
Textron
Textron ESG105L Manual de usuario
Tyco Electronics
Tyco Electronics 90035-3 Manual de usuario
Emerson
Emerson Klauke ES 20RMCCFB Manual de usuario
Continental Refrigerator
Continental Refrigerator PC150HD Manual de usuario
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario