ML Accessories OPRCDKIT Manual de instrucciones

These instructions should be read carefully and retained after installation by the

end user for future reference and maintenance.

These instructions should be used to aid installation of the following product:

OPRCDKIT

GENERAL INSTRUCTIONS

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building Regulations. If in any doubt, consult a

qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this product is ﬁtted) does not exceed

the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location

for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is Class I and must be earthed

• This product is IP66 rated (outdoor socket outlet) / IP20 rated (RCD plug)

INSTALLATION

• Choose a suitable position for the outdoor socket outlet. It should be ﬁxed to a rigid ﬂat

surface as unevenness could cause damage to the product or affect operation

• Choose a suitable location close to the socket outlet to bring the supply cable through

the wall to inside the building

• Drill a suitable hole through the wall, ensuring not to infringe with any gas/water pipes

or electrical cables. The hole should slope very slightly down towards the outside in order

to prevent water ingress through the wall

• Remove the socket outlet front assembly from the backbox and carefully lift off the gasket.

Drill the required number of ﬁxing holes in the backbox (see Fig. 1)

• Using the backbox as a template, mark the location for, and drill the ﬁxing holes ensuring

not to infringe with any gas/water pipes or electrical cables

Fig. 1

• The backbox has drain hole drilling guides marked (see Fig. 2). Drilling a drain hole is

advised if the unit is installed in a location subject to temperature ﬂuctuations where

build-up of condensation may occur. It is not advised if the unit will be subject to spray

or jets, as drilling a drain hole will reduce the IP rating. A 3-5mm hole can be drilled at

the bottom back edge of the enclosure where marked

• Remove one of the pre-ﬁtted blank plugs as required by pushing out from the inside

Remove the lock ring from the IP66 gland, insert the gland through the hole, screw the

lock ring onto the gland and tighten. Any unused cable entries must have the blank plugs

ﬁtted

• Feed the mains cable into the unit and tighten the gland onto the cable

• Secure the baseplate to the surface. The ﬁxing holes are slotted to allow some rotational

adjustment

• Replace the gasket onto the backbox, then wire as shown in Fig. 3 ensuring the correct

polarity is observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)

Fig. 2

• An earth connection must be made to the earth terminal of the socket.

The earth terminal in the backbox is provided for convenience and does not need to be

connected

• Check all electrical connections are secure with no loose strands of cable

• Ensuring the gasket does not become damaged or pinched, ﬁt the socket assembly

onto the backbox, taking care not to compress, damage or trap any cables, and secure with

the screws provided - do not overtighten

• Fit screw covers

• Pass the cable through the wall and cut to suitable length if required

• Remove the terminal cover from the RCD plug and wire as shown in Fig. 4 ensuring the

correct polarity is observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)

Fig. 3

Fig. 2

•Remove one of the pre-fitted blank plugs as required by pushing out from the inside. Remove the lock

ring from the IP66 gland, insert the gland through the hole, screw the lock ring onto the gland and

tighten. Any unused cable entries must have the blank plugs fitted

•Feed the mains cable into the unit and tighten the gland onto the cable

•Secure the baseplate to the surface. The fixing holes are slotted to allow some rotational adjustment

•Replace the gasket onto the backbox, then wire as shown in Fig. 3 ensuring the correct polarity is

observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)

Fig. 3

•An earth connection must be made to the earth terminal of the socket. The earth terminal in the

backbox is provided for convenience and does not need to be connected

•Check all electrical connections are secure with no loose strands of cable

•Ensuring the gasket does not become damaged or pinched, fit the socket assembly onto the backbox,

taking care not to compress, damage or trap any cables, and secure with the screws provided - do not

overtighten

•Fit screw covers

•Pass the cable through the wall and cut to suitable length if required

•Remove the terminal cover from the RCD plug and wire as shown in Fig. 4 ensuring the correct polarity

is observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)

Fig. 4

•Secure the cable with the cord grip provided

•Close the terminal cover and fasten with the screws provided

•Plug the RCD plug into a socket outlet, switch on and check for correct operation. See below for

operation of the RCD

For security, and to prevent unwanted tampering with the socket outlet, a lug feature with a 6mm hole is

provided to accept a padlock or similar locking security device (not included).

Note: The power indicator is lit when there is power to the unit and the switch is on, irrespective of whether a

load is plugged in or not.

RCD TEST PROCEDURE

When the RCD is first plugged in, press the green RESET button to switch on the supply to the socket. The red

indicator should appear.

To test that the RCD is operating correctly, press the blue TEST button. The red indicator should turn black and

power to the socket should be disconnected.

To restore power, press the green RESET button. The red indicator should reappear.

If the RCD should trip due to a fault, the RESET button can be pressed after the fault is rectified. If the RCD will

not reset, remove any connected loads from the socket outlet and check for water ingress or damage.

Following a power cut the RCD will automatically reset itself and does not need manually resetting. Care should

be taken to avoid connected loads powering up without warning.

The TEST button should be pressed at regular intervals to check that the RCD is functioning correctly. We

recommend testing every 3 months. If the red indicator does not turn black when the TEST button is pressed,

do not use.

The RCD plug is fitted with a 13A fuse to BS1362. To replace the fuse, gently prise open the fuse carrier with a

small flat-bladed screwdriver.

WARNING

To ensure continued safe and proper weatherproof operation, the unit must not be left with the cover raised

open or the catch left unlocked.

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

ACCESSORIES LTD ACCESSORIES LTD ACCESSORIES LTD

ACCESSORIES LTD

Tabla de contenidos

Otros manuales de Equipo de iluminación de ML Accessories

ML Accessories

ML Accessories Knightsbridge SFPL Series Manual de instrucciones

ML Accessories

ML Accessories 4IPB Manual de instrucciones

ML Accessories

ML Accessories WALL1 Manual de instrucciones

ML Accessories

ML Accessories Knightsbridge EMTWINPC Manual de instrucciones

ML Accessories

ML Accessories SPIKEW Manual de instrucciones

ML Accessories

ML Accessories T8BLED15EM1 Manual de instrucciones

ML Accessories

ML Accessories SURF418HF Manual de instrucciones

ML Accessories

ML Accessories TRLED12 Manual de instrucciones

ML Accessories

ML Accessories EMLSUS Manual de instrucciones

ML Accessories

ML Accessories SURF236HF Manual de instrucciones

ML Accessories

ML Accessories OWALL1 P Series Manual de instrucciones

ML Accessories

ML Accessories RDSHCBR Manual de instrucciones

ML Accessories

ML Accessories BT ACT Series Manual de instrucciones

ML Accessories

ML Accessories RW6WW Manual de instrucciones

ML Accessories

ML Accessories EMPDL Manual de instrucciones

ML Accessories

ML Accessories FLN10 Manual de instrucciones

ML Accessories

ML Accessories AC65136EM Manual de instrucciones

ML Accessories

ML Accessories CAPWGU Manual de instrucciones

ML Accessories

ML Accessories MLRCTM2 Manual de instrucciones

ML Accessories

ML Accessories UNDKIT3WWW Manual de instrucciones

ML Accessories

ML Accessories LWR2G Manual de instrucciones

ML Accessories

ML Accessories GUSPBK Manual de instrucciones

ML Accessories

ML Accessories E27PR Manual de instrucciones

ML Accessories

ML Accessories AMLEDB Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario