ML Accessories EMPDL Manual de instrucciones

INSTALLATION & MAINTENANCE MANUAL

EMPDL

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following product:

EMPDL

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is ﬁtted) does not exceed the rating of the

circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• Allow 50mm above and around the ﬁtting for air dissipation (do not cover the ﬁtting with insulation)

• This product is for indoor use only

• This product is Class II double insulated

• This product is IP20 rated

SAFETY

INSTALLATION

• Provide power to the required point of installation

• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to infringe

with any joists, gas / water pipes or electrical cables

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following product:

EMPDL

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of

the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)

•This product is for indoor use only

•This product is Class II double insulated

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas / water pipes or electrical cables

Fig. 1

•This fitting will suit 70mm – 130mm cut-outs when using the adaptor ring (see Fig. 2)

Fig. 2

Fig. 1

• This ﬁtting will suit 70mm – 130mm cut-outs when using the adaptor ring (see Fig. 2)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following product:

EMPDL

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of

the circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)

•This product is for indoor use only

•This product is Class II double insulated

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas / water pipes or electrical cables

Fig. 1

•This fitting will suit 70mm – 130mm cut-outs when using the adaptor ring (see Fig. 2)

Fig. 2

• Connect the luminaire to the mains supply via a suitable junction box (not supplied) ensuring the correct

polarity is observed: L - Live (brown), N - Neutral (blue) (see Fig. 3)

GENERAL

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole

luminaire should be replaced.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

•Connect the luminaire to the mains supply via a suitable junction box (not supplied) ensuring the

correct polarity is observed: L - Live (brown), N - Neutral (blue) (see Fig. 3)

Fig. 3

•Connect the battery via the plug and socket to the inverter

•Place the battery and inverter into the ceiling void ensuring that there is at least 50mm of clearance

above and around them

•Lift both of the spring clips on the sides of the luminaire and push into the ceiling

•Switch on and check for correct operation, ensuring the green indicator LED is illuminated

•We recommend, on commissioning the installation, a minimum charge period of 24-36 hours before

carrying out an emergency duration test

•If the batteries have been left in a discharged state for an extended period, we recommend that one or

more charge and discharge cycles are completed which should help to restore the battery capacity

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole

luminaire should be replaced.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.

This product is non-dimmable.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local

authorities for the disposal of this toxic waste.

WARRANTY

This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the

batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned

to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for

any installation costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product specification without prior notice.

TESTING FOR EMERGENCY LUMINAIRES

Recommended routine test procedure in accordance with BS5266

•Daily check – check LED charge indicator is illuminated

•Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch

or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator is

illuminated

•Annual three hour duration test - simulate a mains supply failure for three hour continuous test by operation

of key switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge

indicator is illuminated

•If the luminaire fails any of the above tests, please contact a qualified electrician. See below for test record

sheet

Fig. 3

• Connect the battery via the plug and socket to the inverter

• Place the battery and inverter into the ceiling void ensuring that there is at least 50mm of clearance above

and around them

• Lift both of the spring clips on the sides of the luminaire and push into the ceiling

• Switch on and check for correct operation, ensuring the green indicator LED is illuminated

• We recommend, on commissioning the installation, a minimum charge period of 24-36 hours before

carrying out an emergency duration test

• If the batteries have been left in a discharged state for an extended period, we recommend that one or more

charge and discharge cycles are completed which should help to restore the battery capacity

WARRANTY

This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal

of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should

be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept

responsibility for any installation costs associated with the replacement product. Your statutory rights are not

affected. ML Accessories reserve the right to alter product speciﬁcation without prior notice.

Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.

This product is non-dimmable.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local

authorities for the disposal of this toxic waste.

Recommended routine test procedure in accordance with BS5266

• Daily check – check LED charge indicator is illuminated

• Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch

or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator is

illuminated

• Annual three hour duration test - simulate a mains supply failure for three hour continuous test by operation

of key switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge

indicator is illuminated

• If the luminaire fails any of the above tests, please contact a qualiﬁed electrician. See below for test record

sheet

TESTING FOR EMERGENCY LUMINAIRES

230V 50Hz, IP20, Class 2, Non-Dim, Non-IC, house, Ta 0~45

DCxxx21_V2

DCSEP21_V2

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

45°C

Tabla de contenidos

Otros manuales de Equipo de iluminación de ML Accessories

ML Accessories

ML Accessories TPOV60B Manual de instrucciones

ML Accessories

ML Accessories BL01BK Manual de instrucciones

ML Accessories

ML Accessories LSPIKEA Manual de instrucciones

ML Accessories

ML Accessories ENM5 Manual de instrucciones

ML Accessories

ML Accessories SHE1B Manual de instrucciones

ML Accessories

ML Accessories RWL2A Manual de instrucciones

ML Accessories

ML Accessories EMLRECL Manual de instrucciones

ML Accessories

ML Accessories NH027 Manual de instrucciones

ML Accessories

ML Accessories NCLB12 Manual de instrucciones

ML Accessories

ML Accessories OWALL1 Series Manual de instrucciones

ML Accessories

ML Accessories ENM5C Manual de instrucciones

ML Accessories

ML Accessories AC65118 Manual de instrucciones

ML Accessories

ML Accessories 5410A Manual de instrucciones

ML Accessories

ML Accessories NH023AW Manual de instrucciones

ML Accessories

ML Accessories AXREMC Manual de instrucciones

ML Accessories

ML Accessories TPR14LEDS Manual de instrucciones

ML Accessories

ML Accessories SURF236HF Manual de instrucciones

ML Accessories

ML Accessories T8BLED12 Manual de instrucciones

ML Accessories

ML Accessories EAPIR1BK Manual de instrucciones

ML Accessories

ML Accessories CFR5CCT Manual de instrucciones

ML Accessories

ML Accessories LEDFRA6 Manual de instrucciones

ML Accessories

ML Accessories SUR5LED Manual de instrucciones

ML Accessories

ML Accessories E27PR Manual de instrucciones

ML Accessories

ML Accessories UNDKIT3WWW Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario