Mitsubishi Electric GOT2000 Series Manual de usuario

GRAPHIC OPERATION TERMINAL

User's Manual (Utility)

GOT2000 Series

A - 1

Thank you for choosing Mitsubishi Electric Graphic Operation Terminal (Mitsubishi GOT).

Read this manual and make sure you understand the functions and performance of the GOT thoroughly

in advance to ensure correct use.

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual

carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

Note that the caution level may lead to a serious accident according to the circumstances. Always

follow the instructions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

WARNING

Some failures of the GOT, communication unit or cable may keep the outputs on or off.

Some failures of a touch panel may cause malfunction of the input objects such as a touch switch.

An external monitoring circuit should be provided to check for output signals which may lead to a

serious accident.Not doing so can cause an accident due to false output or malfunction.

Do not use the GOT as the warning device that may cause a serious accident.

An independent and redundant hardware or mechanical interlock is required to configure the device

that displays and outputs serious warning.

Failure to observe this instruction may result in an accident due to incorrect output or malfunction.

WARNING

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

A - 2

[DESIGN PRECAUTIONS]

WARNING

When the GOT backlight has a failure, the GOT status will be as follows. Failure to observe this

instruction may result in an accident due to incorrect output or malfunction.

• GT27, GT25, GT23

The POWER LED blinks (orange/blue), the display section dims, and inputs by a touch switch are

disabled.

• GT2105-Q

The POWER LED blinks (orange/blue), and the display section dims. However, inputs by a touch

switch are still available.

• GT2107, GT2104-R, GT2104-P, GT2103-P

The display section dims. However, inputs by a touch switch are still available.

Even if the display section dims, inputs by a touch switch may still be available. This may cause an

unintended operation of the touch switch.

For example, if an operator assumes that the display section has dimmed because of the screen

save function and touches the display section to cancel the screen save, a touch switch may be

activated.

The GOT backlight failure can be checked with a system signal of the GOT. (This system signal is

not available on GT2107, GT2104-R, GT2104-P, and GT2103-P.)

The display section of the GOT is an analog-resistive type touch panel.

When multiple points of the display section are touched simultaneously, an accident may occur due

to incorrect output or malfunction.

•GT27

Do not touch three points or more simultaneously on the display section. Doing so may cause an

accident due to an incorrect output or malfunction.

• GT25, GT23, GT21

Do not touch two points or more simultaneously on the display section. Doing so may cause a

touch switch near the touched points to operate unexpectedly, or may cause an accident due to

an incorrect output or malfunction.

When programs or parameters of the controller (such as a PLC) that is monitored by the GOT are

changed, be sure to reset the GOT, or turn on the unit again after shutting off the power as soon as

possible.

Not doing so can cause an accident due to false output or malfunction.

If a communication fault (including cable disconnection) occurs during monitoring on the GOT,

communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.

For bus connection (GT27, GT25 Only) : The CPU becomes faulty and the GOT becomes

inoperative.

For other than bus connection : The GOT becomes inoperative.

A system where the GOT is used should be configured to perform any significant operation to the

system by using the switches of a device other than the GOT on the assumption that a GOT

communication fault will occur.

Not doing so can cause an accident due to false output or malfunction.

A - 3

[DESIGN PRECAUTIONS]

[MOUNTING PRECAUTIONS]

CAUTION

Do not bundle the control and communication cables with main-circuit, power or other wiring.

Run the above cables separately from such wiring and keep them a minimum of 100mm apart.

Not doing so noise can cause a malfunction.

Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

When the GOT connects to an Ethernet network, the IP address setting is restricted according to the

system configuration.

• GT27,GT25,GT23

When a GOT2000 series model and a GOT1000 series model are on an Ethernet network, do not

set the IP address 192.168.0.18 for the GOTs and the controllers on this network.

Doing so can cause IP address duplication at the GOT startup, adversely affecting the

communication of the device with the IP address 192.168.0.18.

The operation at the IP address duplication depends on the devices and the system.

•GT21

• When multiple GOTs connect to the Ethernet network:

Do not set the IP address (192.168.3.18) for the GOTs and the controllers in the network.

• When one GOT connects to the Ethernet network:

Do not set the IP address (192.168.3.18) for the controllers other than the GOT in the network.

Doing so can cause IP address duplication at the GOT startup, adversely affecting the

communication of the device with the IP address 192.168.3.18.

The operation at the IP address duplication depends on the devices and the system.

When using the Ethernet interfaces, set an IP address for each interface to access a different

network.

Turn on the controllers and the network devices to be ready for communication before they

communicate with the GOT.

Failure to do so can cause a communication error on the GOT.

When the GOT is subject to shock or vibration, or some colors appear on the screen of the GOT, the

screen of the GOT might flicker.

WARNING

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the GOT main unit to/from the panel.

Not doing so can cause the unit to fail or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting or

removing the option unit onto/from the GOT. (GT27, GT25 Only)

CAUTION

Use the GOT in the environment that satisfies the general specifications described in this manual.

Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

A - 4

[MOUNTING PRECAUTIONS]

CAUTION

When mounting the GOT to the control panel, tighten the mounting screws in the specified torque

range with a Phillips-head screwdriver No. 2.

• GT27, GT25, GT23, GT2107

Specified torque range (0.36 N•m to 0.48 N•m)

• GT2105-Q

Specified torque range (0.30 N•m to 0.50 N•m)

• GT2104-R, GT2104-P, GT2103-P

Specified torque range (0.20 N•m to 0.25 N•m)

Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the

GOT.

When mounting a unit on the GOT, tighten the mounting screws in the following specified torque

range.

• GT27, GT25 (except GT25-W)

When loading the communication unit or option unit other than wireless LAN unit to the GOT, fit it

to the connection interface of the GOT and tighten the mounting screws in the specified torque

range (0.36 N•m to 0.48 N•m) with a Phillips-head screwdriver No. 2.

When loading the wireless LAN unit to the GOT, fit it to the side interface of GOT and tighten the

mounting screws in the specified torque range (0.10 N•m to 0.14 N•m) with a Phillips-head

screwdriver No. 1.

When the GOT is installed vertically, its side interface is positioned on the bottom.

To prevent the falling of the wireless LAN communication unit from the side interface, install or

remove the unit while holding it with hands.

• GT25-W

When mounting the wireless LAN communication unit on the GOT, fit it to the wireless LAN

communication unit interface and tighten the mounting screws in the specified torque range (0.10

N•m to 0.14 N•m) with a Phillips-head screwdriver No.1.

• GT2103-P

When mounting the SD card unit on the GOT, fit it to the side of the GOT and tighten the tapping

screws in the specified torque range (0.3 N•m to 0.6 N•m) with a Phillips-head screwdriver No. 2.

Under tightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, failure or malfunction due to the damage of the screws or unit.

When closing the USB environmental protection cover, note the following points to ensure the IP

rating.

• GT27, GT25 (except GT25-W)

Push the [PUSH] mark on the latch firmly to fix the cover to the GOT.

• GT25-W, GT2107

Push the [PULL] mark on the latch firmly to fix the cover to the GOT.

• GT2105-Q

Tighten the lower fixing screws of the cover in the specified torque range (0.36 N•m to 0.48 N•m)

to fix the cover to the GOT.

Remove the protective film of the GOT.

When the user continues using the GOT with the protective film, the film may not be removed.

In addition, for the models equipped with the human sensor function, using the GOT with the

protective film may cause the human sensor not to function properly

A - 5

[MOUNTING PRECAUTIONS]

[WIRING PRECAUTIONS]

CAUTION

For GT2512F-S, GT2510F-V, and GT2508F-V, attach an environmental protection sheet dedicated

to the open frame model (sold separately) to the display section.

Or, attach a user-prepared environmental protection sheet.

Not doing so may damage or soil the GOT or cause foreign matter to enter the GOT, resulting in a

failure or malfunction.

When installing the supplied fittings on GT2512F-S, GT2510F-V, or GT2508F-V, tighten screws in

the specified torque range (0.8 N•m to 1.0 N•m).

Meld studs on the control panel to fasten the fittings.

The studs must have strength adequate to withstand a tightening torque of 0.9 N•m or more.

Make sure that no foreign matter such as welding waste is at and around the bases of the studs.

Tighten nuts on the studs in the specified torque range (0.8 N•m to 0.9 N•m) with a wrench for M4

nuts.

Undertightening a screw or nut may cause the GOT to drop, short-circuit, or malfunction.

Overtightening a screw or nut may damage it or the GOT, causing the GOT to drop, short-circuit, or

malfunction.

Operate and store the GOT in environments without direct sunlight, high temperature, dust, humidity,

and vibrations.

When using the GOT in the environment of oil or chemicals, use the protective cover for oil.

Failure to do so may cause failure or malfunction due to the oil or chemical entering into the GOT.

WARNING

Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

CAUTION

When grounding the FG terminal and LG terminal of the GOT power supply section, note the

following points.

Not doing so may cause an electric shock or malfunction.

• GT27, GT25, GT23, GT2107, GT2105-Q

Make sure to ground the FG terminal and LG terminal of the GOT power supply section solely for

the GOT (ground resistance: 100 Ωor less, ground cable diameter: 1.6 mm or more). (GT2705-V,

GT25-W, GT2107 and GT2105-Q do not have the LG terminal.)

• GT2104-R, GT2104-P, GT2103-P

Make sure to ground the FG terminal of the GOT power supply section with a ground resistance of

100 Ωor less. (For GT2104-PMBLS and GT2103-PMBLS, grounding is unnecessary.)

A - 6

[WIRING PRECAUTIONS]

CAUTION

When tightening the terminal screws, use the following screwdrivers.

• GT27, GT25, GT23, GT2107, GT2105-Q

Use a Phillips-head screwdriver No. 2.

• GT2104-R, GT2104-P, GT2103-P

For the usable screwdrivers, refer to the following.

➠GOT2000 Series User's Manual (Hardware)

Tighten the terminal screws of the GOT power supply section in the following specified torque range.

• GT27, GT25, GT23

Specified torque range (0.5 N•m to 0.8 N•m)

For a terminal processing of a wire to the GOT power supply section, use the following terminal.

• GT27, GT25, GT23, GT2107, GT2105-Q

Use applicable solderless terminals for terminal processing of a wire and tighten them with the

specified torque.

Not doing so can cause a fire, failure or malfunction.

• GT2104-R, GT2104-P, GT2103-P

Connect a stranded wire or a solid wire directly, or use a rod terminal with an insulation sleeve.

Correctly wire the GOT power supply section after confirming the rated voltage and terminal

arrangement of the product.

Not doing so can cause a fire or failure.

Tighten the terminal screws of the GOT power supply section in the following specified torque range.

• GT27, GT25, GT23, GT2107, GT2105-Q

Specified torque range (0.5 N•m to 0.8 N•m)

• GT2104-R, GT2104-P, GT2103-P

Specified torque range (0.22 N•m to 0.25 N•m)

Exercise care to avoid foreign matter such as chips and wire offcuts entering the GOT.

Not doing so can cause a fire, failure or malfunction.

The module has an ingress prevention label on its top to prevent foreign matter, such as wire offcuts,

from entering the module during wiring.

Do not peel this label during wiring.Before starting system operation, be sure to peel this label

because of heat dissipation. (GT27, GT25 Only)

Plug the communication cable into the GOT interface or the connector of the connected unit, and

tighten the mounting screws and the terminal screws in the specified torque range.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

Plug the QnA/ACPU/Motion controller(A series) bus connection cable by inserting it into the

connector of the connected unit until it "clicks".

After plugging, check that it has been inserted snugly.

Not doing so can cause a malfunction due to a contact fault. (GT27, GT25 Only)

A - 7

[TEST OPERATION PRECAUTIONS]

[STARTUP/MAINTENANCE PRECAUTIONS]

WARNING

Before testing the operation of a user-created monitor screen (such as turning on or off a bit device,

changing the current value of a word device, changing the set value or current value of a timer or

counter, and changing the current value of a buffer memory), thoroughly read the manual to fully

understand the operating procedures.

During the test operation, never change the data of the devices which are used to perform significant

operation for the system.

False output or malfunction can cause an accident.

WARNING

When power is on, do not touch the terminals.

Doing so can cause an electric shock or malfunction.

Correctly connect the battery connector.

Do not charge, disassemble, heat, short-circuit, solder, or throw the battery into the fire.

Doing so will cause the battery to produce heat, explode, or ignite, resulting in injury and fire.

Before starting cleaning or terminal screw retightening, always switch off the power externally in all

phases.

Not switching the power off in all phases can cause a unit failure or malfunction.

Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

CAUTION

Do not disassemble or modify the unit.

Doing so can cause a failure, malfunction, injury or fire.

Do not touch the conductive and electronic parts of the unit directly.

Doing so can cause a unit malfunction or failure.

The cables connected to the unit must be run in ducts or clamped.

Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental

pulling of the cables or can cause a malfunction due to a cable connection fault.

When unplugging the cable connected to the unit, do not hold and pull from the cable portion.

Doing so can cause the unit or cable to be damaged or can cause a malfunction due to a cable

connection fault.

Do not drop the module or subject it to strong shock. A module damage may result.

A - 8

[STARTUP/MAINTENANCE PRECAUTIONS]

[TOUCH PANEL PRECAUTIONS]

[PRECAUTIONS WHEN THE DATA STORAGE IS IN USE]

CAUTION

Do not drop or give an impact to the battery mounted to the unit.

Doing so may damage the battery, causing the battery fluid to leak inside the battery.

If the battery is dropped or given an impact, dispose of it without using.

Before touching the unit, always touch grounded metals, etc. to discharge static electricity from

human body, etc.

Not doing so can cause the unit to fail or malfunction.

Use the battery manufactured by Mitsubishi Electric Corporation.

Use of other batteries may cause a risk of fire or explosion.

Dispose of used battery promptly.

Keep away from children.Do not disassemble and do not dispose of in fire.

Be sure to shut off all phases of the external power supply before replacing the battery or using the

dip switch of the terminating resistor.

Not doing so can cause the unit to fail or malfunction by static electricity.

CAUTION

For the analog-resistive film type touch panels, normally the adjustment is not required.

However, the difference between a touched position and the object position may occur as the period

of use elapses.

When any difference between a touched position and the object position occurs, execute the touch

panel calibration.

When any difference between a touched position and the object position occurs, other object may be

activated.

This may cause an unexpected operation due to incorrect output or malfunction.

WARNING

If the SD card is removed from drive A of the GOT while being accessed by the GOT, the GOT may

stop processing data for about 20 seconds.

The GOT cannot be operated during this period.

The functions that run in the background including a screen updating, alarm, logging, scripts, and

others are also interrupted.

Before removing the SD card, check the following items.

• GT27, GT25, GT23

Check that the SD card access LED is off before removing the SD card.

•GT21

Disable the SD card access in the GOT utility, and then check that the SD card access LED is off

before removing the SD card.

Otros manuales para GOT2000 Series

Tabla de contenidos

Otros manuales de Terminal táctil de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric GOT SIMPLE Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Instrucciones de uso

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT 1000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT 1000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT14 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT-A900 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MAC 10 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric E1100 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT2103-PMBDS Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1695M-XTBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Got 1000 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric A960GOT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1155HS-QSBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric E1071 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT11 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1685 Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT 1000 Series Instrucciones de funcionamiento y mantenimiento

Mitsubishi Electric

Mitsubishi Electric GT2512-STBA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric F940 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric E1032 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario