Mitsubishi Electric F940 Manual de usuario

HARDWARE MANUAL

F940GOT-SWD-E/LWD-E

Foreword

• This manual contains text, diagrams and explanations which will guide the reader in the

correct installation and operation of the communication facilities of FX series.

• Before attempting to install or use the communication facilities of FX series this manual

should be read and understood.

• If in doubt at any stage of the installation of the communication facilities of FX series

always consult a professional electrical engineer who is qualified and trained to the local

and national standards which apply to the installation site.

F940GOT-SWD-E/LWD-E

HARDWARE MANUAL Manual number : JY992D77901

Manual revision : D

Date : February 2000

F940GOT-SWD-E/LWD-E

Guidelines for the safety of the user and protection of the F940GOT-SWD-E/LWD-E

This manual provides information for the installation and use of the Graphic Operation Terminal F940GOT.

The manual has been written to be used by trained and competent personnel. The definition of such a person

or persons is as follows;

a ) Any engineer who is responsible for the planning, design and construction of automatic equipment

using the product associated with this manual should be of a competent nature, (trained and qualified

to the local and national standards required to fulfill that role). These engineers should be fully aware

of safety with regards to automated equipment.

b ) Any commissioning or service engineer must be of a competent nature, trained and qualified to the

local and national standards required to fulfill that job. These engineers should also be trained in the

use and maintenance of the completed product. This includes being completely familiar with all asso-

ciated documentation for the said product. All maintenance should be carried out in accordance with

established safety practices.

c ) All operators of the compliance product should be trained to use that product in a safe and coordi-

nated manner in compliance to established safety practices. The operators should also be familiar

with all documentation which is connected with the actual operation of the completed equipment.

Note:The term ‘completed equipment’ refers to a third party constructed device which contains or uses the

product associated with this manual.

F940GOT-SWD-E/LWD-E

iii

Note’s on the symbology used in this manual

At various times through out this manual certain symbols will be used to highlight points of information which

are intended to ensure the users personal safety and protect the integrity of the equipment. Whenever any of

the following symbols are encountered, its associated note must be read and understood. Each of the sym-

bols used will now be listed with a brief description of its meaning.

Hardware warnings

Software warnings

1 ) Indicates that the identified danger WILL cause physical and property damage.

2 ) Indicates that the identified danger POSSIBLY cause physical and property damage.

3 ) Indicates a point of further interest or further explanation.

1 ) Indicates special care must be taken when using this element of software.

2 ) Indicates a special point of which the user of the associate software element should be aware.

3 ) Indicates a point of interest or further explanation.

F940GOT-SWD-E/LWD-E

Memo

F940GOT-SWD-E/LWD-E

CONTENTS

1. INTRODUCTION...................................................................................1-1

1.1 Outline of product................................................................................................1-2

1.2 Product configuration...........................................................................................1-8

1.3 System configuration.........................................................................................1-14

2. Installation, Wiring and General Specifications.....................................2-1

2.1 Installation of main body......................................................................................2-1

2.2 Wiring of power supply........................................................................................2-4

2.3 Functions of operation keys and connectors.......................................................2-9

2.4 Outside dimensions...........................................................................................2-12

2.5 General specificationsl ......................................................................................2-13

2.6 Connection to personal computer......................................................................2-15

2.7 CPU port connection .........................................................................................2-18

2.8 Computer link port connection (MELSEC A Series)..........................................2-26

2.9 Connection to SYSMAC C Series .....................................................................2-29

2.10 Connection to FLEX-PC N Series .....................................................................2-32

2.11 Connection by general-purpose communication ...............................................2-35

3. Startup...................................................................................................3-1

3.1 Startup procedure................................................................................................3-2

3.2 Operation environment setting ............................................................................3-5

4. Extension Module..................................................................................4-1

4.1 Data transfer adaptor...........................................................................................4-1

F940GOT-SWD-E/LWD-E

5. Maintenance..........................................................................................5-1

5.1 Outline of maintenance........................................................................................5-1

5.2 Replacement of battery .......................................................................................5-3

5.3 Replacement of backlight....................................................................................5-5

6. Troubleshooting.....................................................................................6-1

6.1 Power indication ..................................................................................................6-1

7. Additional Functions (in Ver3.00 or later)..............................................7-1

7.1 Applicable Versions and Models .........................................................................7-1

7.2 Connection to MELSEC QnA Series PC.............................................................7-2

7.3 Connection to SLC 500 Series............................................................................7-3

7.4 Connection to Bar Code Reader .........................................................................7-5

7.5 Screen Hard Copy Function ................................................................................7-7

7.6 Additional Function in Alarm History Display.......................................................7-8

7.7 Specification of Ten-Key Window Initial Display Position....................................7-8

8. Additional Functions (in V3.10 or later) .................................................8-1

8.1 Applicable Versions and Models .........................................................................8-1

9. Additional Functions (in V4.00 or later) .................................................9-1

9.1 Applicable Versions and Models .........................................................................9-1

Note to User

This manual describes installation, wiring and the specifications of the F940GOT.

For handling and operating procedures of the F940GOT main body, refer to the

F940GOT Operation Manual offered separately.

INTRODUCTION 1.

1-1

1. INTRODUCTION

This section describes the product configuration and the system configuration of the graphic

operation terminal.

Confirm various functions of each unit.

F940GOT-SWD-E/LWD-E

F940GOT-SWD-E/LWD-E INTRODUCTION 1.

1-2

1.1 Outline of product

The graphic operation terminal (which may be hereafter

abbreviated as "GOT") is attached on the panel face of a

control panel or an operation panel, and connected to a

program connector in an FX or A Series programmable

controller (which may be hereafter abbreviated as "PLC")

(except the A0J2) inside the control panel.

Not only the CPU port connection method but also the

computer link port connection method is available so that

the GOT can be connected to a PLC other than MELSEC

or a micro computer board.

You can monitor various devices and change the data of

the PLC while checking the screen of the GOT.

There are several display screens built in the GOT which

offer various functions. In addition, you can create display

screens.

The built-in screens (system screens) and the screens

made by the user (user screens) have the following func-

tions respectively.

FX or

A Series PLC

Program

connector

GOT main body

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Terminal táctil de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric F930GOT-BWD-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT2508-VTBA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT16 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric E1032 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric FA-TH16XRA20S Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT2104-PMBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT2103-PMBDS Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT2103-PMBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Guía de instalación

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT1000 GT14 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1685 Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT 1000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric E1071 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1695M-XTBD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT2000 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric GOT 1000 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric A960GOT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MAC 10 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario