MIMAKI CF-0912 Manual de usuario

RECIPROCAL FLAT BED CUTTING PLOTTER

CF Series

D200962

RC model

RT model

INSTRUCTION MANUAL

MIMAKI ENGINEERING CO., LTD.

TKB Gotenyama Building, Kitashinagawa, Shinagawa-ku, Tokyo 141-0001, Japan

Phone: +81-3-5420-8671 Fax: +81-3-5420-8687

URL: http: // www. mimaki. co. jp

1. Prior to using this device, be sure to read this Instruction Manual and become fully famil-

iar with its operation method and usage cautions.

2. While the plotter is operating (while it is moving or its blades are vibrating), absolutely

never bring any part of your body (face, hands), clothes, or other objects near the flat bed

(cutting panel), as serious injury may result.

Particularly when lifting the head and operating the device without a work piece in order

to check data, one's hand can enter under the head safety cover. As this may cause

serious injury, proceed with great care.

3. The head units (A, B, C) move at high speed. When checking work results or adjusting

work slippage or floating, be sure to stop the device and perform these actions in either

the local mode or with the power switched off.

4. When attaching tools (reciprocal cutter, etc.), be sure to power off the device beforehand.

Attempting to change tools while the power is on presents the risk of unexpected injuries

due to erroneous panel operation, etc.

CAUTION

This device is a first-class information processing device (information processing device that

shall be commissioned in a commercial and industrial area) and conforms to the Voluntary

Control Council Interference (VCCI) standard that has been developed for the purpose of

prevention of radio disturbance in commercial or industrial areas. This device, therefore, can

interfere with radios and televisions if put into service in a residential area and its adjacent

areas. Correct handling procedure shall be followed according to this Instruction Manual.

In the case where MIMAKI-designated cable is not used for the connection of this device, limits

provided by VCCI rules can be exceeded. To prevent this, use of MIMAKI-designated cable is

essential for the connection of this device.

Interference to televisions and radios

The product covered by this Instruction Manual produces high frequency waves while it is in opera-

tion. The product can interfere with radios and televisions if set up or commissioned under

improper conditions. The product is not guaranteed against any damage to specific-purpose radio

and televisions. The product’s interference with your radio or television will be checked by turning

off the power to the product.

If the interference is elimiated by turning the product off, the product is the cause of interference.

In the event that the product is the cause of interference, try to elimiate it by taking one of th

following corrective measures or taking some of them in combination.

•Change the direction of the antenna of your radio/television to find one that avoids interference.

•Install your radio/television at a place that is sufficiently spaced from the product.

•Connect the plug of your radio/television into a receptacle that does not share the power supply

with the product.

CAUTION

•MIMAKI ENGINEERING CO., LTD. shall have no liability for any damage of any kind (in-

cluding but not limited to unearned profits, indirect damages, special losses and other debts)

caused by the use of malfunction of the product unless otherwise specified in MIMAKI warranty

provisions. The same applies to any case where MIMAKI ENGINEERING CO., LTD. has been

informed of the possible risk of such damages in prior.

For example, MIMAKI shall not be liable to any damage to media (works) due to the use of the

product or any indirect damage that is caused by a product that is manufactured with damaged

media.

•Reproduction of this manual in whole or in part is strictly prohibited.

— i —

FOREWORD

Congratulations on your purchase of a “CF-Pro Series” of reciprocal flat bed cutting plotter.

This Instruction Manual is intended for RC model and RT model under the “CF-Pro Series.”

Any function for which no head name is designated is common to all models.

Please read and fully understand this Instruction Manual before putting the machine into service.

It is also necessary to keep this Instruction Manual on hand.

•This device uses blades and is extremely dangerous while it is operating. Absolutely

never bring your hands or head near the head as doing so may result in cut fingers,

etc.

NOTES

•Make arrangements to deliver this Instruction Manual to the person in charge of the operation of

this device.

•This Instruction Manual has been carefully prepared for your easy understanding, however, please

do not hesitate to contact a distributor or our office in your country if you have any questions.

• Description contained in this Instruction Manual are subject to change without notice.

•In the case where this Instruction Manual should be illegible due to destruction by fire or break-

age, purchase another copy of the Instruction Manual from our office.

FOR SAFE OPERATION

Prior to using this device, be sure to read this Instruction Manual and become fully familiar with its

operation method and usage cautions.

Pictorial signs

Pictorial signs are used in this Instruction Manual for safe operation of and in

prevention of damages to the device. Pictorial signs and their meanings are given

below. Read and fully understand the following before reading the text.

Indicates the case where it is asumed that misuse of the machine, ignoring this

sign, can expose the operator to danger of injury or death.

Indicates the case where it is assumed that misuse of the machine, ignoring

this sign, can cause danger only to property.

Example of pictorial signs

The symbol “ ” indicates the case where some phenomenon that requires a

CAUTION sign (including “DANGER” and “WARNING” signs) exists. A con-

crete precaution (precaution against an electric shock in the case of the sketch

given on the left) is shown in the illustration.

The symbol “ ” indicates a prohibited behavior. A concrete illustration of

prohibition (disassembly is prohibited on the sketch given on the left) is shown

in or next to the illustration.

The symbol “ ” indicates a thing that is forced to be done and instruction that

is forced to be followed. A concrete illustration of instruction (the removal of a

plug from the receptacle is instructed in the sketch given on the left) is drawn in

the illustration.

The symbol “ ” indicates helpful information that will facilitate the use of

the device.

WARNING

CAUTION

— iii —

Do not disassemble or remodel the device.

*Never disassemble or remodel the

main unit of the plotter and the

blower unit. Disassembling/re-

modeling any of them will result in

electric shocks or breakdown of the

device.

Do not use the device in damp places.

*Avoid damp environments when

putting the device into service. Do

not splash water onto the device.

High-humidity or water will give

rise to fire, electric shocks or

breakdown of the device.

Abnormal event occurs.

*If the device is used under an

abnormal condition where the

device produces smoke or un-

pleasant smell, fire or electric

shocks can result. Be sure to turn

off the power switch immediately

and detach the plug from the

receptacle. Check first to be sure

that the device no longer produces

smoke, and contact a distributor in

your district or MIMAKI office for

repair. Never repair your device by

yourself since it is very dangerous

for you to do so.

Power supply and voltage

*Be sure to use the device with

the power supply specifications

indicated.

Be sure to connect the plug of

the power cable to a grounded

receptacle.

If not, fire or electric shocks can

result.

Handling of the cable

*Take care not to damage, break or

work on the power cable or com-

munication cable. If a heavy matter

is placed on the power cable, heated

or drawn, the power cable can break

to cause fire or electric shocks.

Handling of tools

*Store cutter holders or blades in a

place that is out of the reach of

children. Never place cutter holders

or blades in the tray on the operation

panel.

Preventive measure against dust

*When handling any dust-producing

substance that will jeopardize the

health of personnel, wear a mask or

the like to prevent dust.

Leave maintenance to a serviceman.

*Leave maintenance works to a ser-

viceman whenever the device has

broken. Never conduct maintenance

works by yourself since the works

are always accompanied by

possible risks of electric shocks, etc.

WARNING

Use the following electrical specifications.

Be sure to connect the power cable to

a power outlet with the following

electrical specifications.

Main unit: 100 VAC ±10%

50/60 Hz

500W or higher

Blower: 100 VAC

50/60 Hz

Breaker of 30 A or higher

Do not restart the power until 30 seconds

after turn off.

If the device is restarted, do not turn

on the power until 30 seconds after

turning off. The device may be caused

faulty function.

Do not put any matters on the cable.

Do not bend the power cable and the

communication cable, and do not

placed any matters. These cables may

be broken and heated, the power cable

can cause fire or electric shocks.

Do not dress baggy suits and accessories.

Do not work with dressing baggy suits

and any accessories, and also tie any

long hairs.

Do not move your face in front of cut panel.

Do not move your face and hands in

front of the cut panel while the unit is

working.

The device can wind and touch your

hairs or hands.

The device is moved by our serviceman only.

The device is too sensitive equipment,

so in case if you require movement of

the unit, please contact to our

serviceman.

CAUTION

For safe operation

— v —

A place exposed to direct sunlight

Do not install the device at a place

where the temperature of the cut panel

surface exceeds 60°C. The cut panel

can deform or break down.

A place in which temperature and humidity

vary by a great margin

Use the device under the following

environment.

Operating environment:

10 to 35°C

35 to 75% (Rh)

A place exposed to direct air blow from air

conditioner., etc.

Cutting quality could be adversely

affected.

A plate that is not horizontal

If the plotter is not leveled, the plotter

will fail to give correct results. Also

the tilted plotter can break.

A place that vibrates

The device will fail to give correct

results if installed in a place that

vibrates.

A place filled with dirt, dust or tobacco

smoke

The plotter is a precision machine.

Do not use it in a place that is filled

with dirt and dust.

Near flammable materials

When the blower is used fully open,

the exhaust port temperature becomes

extremely high. Do not place flammable

materials near the blower or in front

of the exhaust port.

CAUTION

Precautions in installation

HOW TO READ THIS INSTRUCTION MANUAL

Name of function shown on LCD

List of values

that can be set

Gives the

description of

operating procedure.

Indication on LCD

is bracketed as

[INTERFACE].

Indicates the key

to be used to select

a function from

indications given on

LCD shown on the

left.

Page number

Number of step

of operating

procedure

LCD display

— vii —

Structure of this Instruction Manual

Chapter 1 Set-up

This chapter describes the procedures to be taken after the unpacking to specify func-

tions that are required for the connection of this device to your computer.

Chapter 2 Basic operation

This chapter describes normal operation of the device such as the replacing/attaching

of tools or works.

Chapter 3 When abnormal conditions are encountered

This chapter describes how to correct troubles after the occurrence of an abnormal

condition on the device.

Chapter 4 Application functions

This chapter describes helpful functions that facilitate operation.

Chapter 5 Self-test

This chapter describes “self-test” that is performed to check whether or not the device

unit has failed.

Appendix

This appendix describes the replacement of blades, menu structure and output smaples

and introduces separately-available parts.

FEATURES OF THE DEVICE

The device is capable of cutting thick materials and flexible materials.

The device can cut thick materials of up to 20 mm thick by moving the cutter up and down at high

speed. It can cut a variety of materials such as sponge and fiberboard, which cannot be cut by

conventional cutting plotters.

Heads corresponding to materials are prepared

RT model: Pen/1.5-kg tangential cutter/reciprocal cutter

RC model: Pen/5-kg tangential cutter/reciprocal cutter

Applicable materials

Upgraded reliability and consistent cutting quality

With its four-axis ( X, Y, Z, θ) software servo control, the device promises upgraded reliability.

With its high-rigid special drive mechanism, the device produces high- precision beautiful cutting

results while preventing overshoot and warp. Furthermore, eccentricity of the cutter holder can be

adjusted through software by the eccentricity correcting function, achieving cutting results with

upgraded accuracy.

Sponge

Vinyl chloride sheet for signboard

Reflecting sheet

Sand-blast rubber

Industrial sheet rubber

Wood rack

Coated board No. 10

RT Model RC Model

Corrugated fiberboard (E to AB corrugation)

Coated board No. 10

Vinyl chloride sheet for signboard

Industrial sheet rubber

Pasteboard

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Trazador de MIMAKI

MIMAKI

MIMAKI JV33 Series Instrucciones de montaje

MIMAKI

MIMAKI UCJV300 Guía de inicio rápido

MIMAKI

MIMAKI UJF-605C Instrucciones de montaje

MIMAKI

MIMAKI CFL-605RT Manual de usuario

MIMAKI

MIMAKI CG-60SRIII Manual de usuario

MIMAKI

MIMAKI GP-604D Manual de usuario

MIMAKI

MIMAKI CF3-1631 Manual de usuario

MIMAKI

MIMAKI TS34-1800A Guía de referencia

MIMAKI

MIMAKI DM3-1810S Manual de usuario

MIMAKI

MIMAKI CG-60AR Instrucciones de instalación

MIMAKI

MIMAKI CG-60EX Manual de usuario

MIMAKI

MIMAKI CF3-1631 Manual de usuario

MIMAKI

MIMAKI CG-60AR Manual de usuario

MIMAKI

MIMAKI JV22-130 Manual de usuario

MIMAKI

MIMAKI JV400-SUV Series Guía de inicio rápido

MIMAKI

MIMAKI CG-60SL Manual de usuario

MIMAKI

MIMAKI JV400-SUV Series Manual de mantenimiento

MIMAKI

MIMAKI UJF-7151 plus Manual de usuario

MIMAKI

MIMAKI CG-60st Manual de usuario

MIMAKI

MIMAKI Tx400 Manual de usuario

MIMAKI

MIMAKI TPC-1000 Manual de usuario

MIMAKI

MIMAKI ME-300STII Manual de usuario

MIMAKI

MIMAKI TPC-1000 Instrucciones de instalación

MIMAKI

MIMAKI JV400-LX Manual de usuario

Manuales populares de Trazador de otras marcas

MUTOH

MUTOH Kona 760 Manual de usuario

HP 7475a Manual de usuario

Vulcan-Hart

Vulcan-Hart FC-500VC Manual de usuario

Roland

Roland TrueVIS VG-640 Manual del propietario

Furuno

Furuno RP-180 Manual de usuario

Roland

Roland VersaCamm SP-540V Manual de usuario

Ioline

Ioline Summit Manual de usuario

Summa

Summa S CLASS Manual de usuario

Gerber Technology

Gerber Technology GERBERplotter MP Series Manual de usuario

Furuno

Furuno RP-17 Manual de usuario

HP 7470A Manual de usuario

SII

SII LP-1010 Manual de usuario

Great Computer

Great Computer JII-61 Manual de usuario

Roland

Roland VersaUv LEF - 12i Manual de usuario

Lectra

Lectra Alys 120 Manual de usuario

MUTOH

MUTOH Ultima SC-850D Manual de usuario

Skycut

Skycut D Series Manual de usuario

Commodore

Commodore 1520 Manual de usuario