Milwaukee PH54 Manual de usuario

pH54

Waterproof pH-meter

USER MANUAL

SPECIFICATIONS

Range 0.00 to 14.00 pH

Resolution 0.01 pH

Accuracy (@25 °C) ±0.1 pH

Calibration Manual, at 2 points

through trimmers

pH electrode MA73600 or

(replaceable) MA73600-S

Environment 0 to 50°C; 100% RH

Battery type 3 x 1.5V, alkaline

Battery life more than 1500

hours of continuous use

Dimensions 165 x 30 x 30 mm

Weight 80 g

ACCESSORIES

MA73600 Replaceable pH electrode

MA73600-S Replaceable pH long

electrode

M10007B pH 7.01 buffer solution,

20 mL sachet (25 pcs)

M10004B pH 4.01 buffer solution,

20 mL sachet (25 pcs)

M10010B pH 10.01 buffer solution,

20 mL sachet (25 pcs)

M10000B Electrode rinse solution,

20 mL sachet (25 pcs)

MA9015 Electrode storage solution,

220 mL bottle

MA9016 Electrode cleaning solution,

220 mL bottle This meter is in compliance with the CE directives.

ISTRPH54 06/18

CONDITIONING:

Remove the cap and immerse the pH54 in

MA9015 storage solution for 2 hours to activate

the electrode.

CALIBRATION:

Unscrew the battery compartment cap on the

top of the meter and perform one of the following

two-point calibration procedure, according to

the required application:

Acid calibration for measurements below pH7:

• Immerse the electrode in pH7.01

(M10007) buffer solution.

• Allow the reading to stabilize and

with a small screwdriver turn the

“7” calibration trimmer inside the

battery compartment until the display

shows “7.01”.

• Rinse the electrode with tap

water and immerse it in pH4.01

(M10004) buffer solution.

• Allow the reading to stabilize and with a small

screwdriver turn the “4” calibration trimmer

until the display shows “4.01”.

Alkaline calibration for measurements above pH7:

• Immerse the electrode in pH7.01 (M10007)

buffer solution.

• Allow the reading to stabilize and with a

small screwdriver turn the “7” calibration

trimmer until the display shows “7.01”.

• Rinse the electrode with tap water and immerse

it in pH10.01 (M10010) buffer solution.

• Allow the reading to stabilize and with a

small screwdriver turn the “4” calibration

trimmer until the display shows “10.01”.

Replace the battery compartment cap.

OPERATION:

• Remove the protective cap.

• Turn the pH54 on by pressing the ON key.

• Immerse the electrode in the solution to be

tested.

• Stir gently and wait for the reading

to stabilize.

• After use, rinse the electrode with

water to minimize contamination.

• Store the electrode with a few

drops of storage (MA9015) or pH7

(M10007) solution in the protective

cap.

• Always replace the protective cap after use.

NEVER USE DISTILLED OR DEIONIZED WATER

FOR STORAGE PURPOSES.

ELECTRODE REPLACEMENT:

The electrode can be easily replaced in the

following way:

• Remove the protective cap.

• Unscrew the plastic ring on the

top of the electrode.

• Pull out the MA73600 (or

MA73600-S) pH electrode and

replace it with a new one (align-

ing the colored pin towards the

LCD side).

• Make sure the gaskets are in place before

screwing back the ring.

BATTERY REPLACEMENT:

The pH54 is going to turn off when the bat-

teries are to weak. To replace the batteries

unscrew the battery compartment cap and

replace all three 1.5V batteries while paying

attention to their polarity. Make sure the gasket

is in place before screwing back the cap.

Batteries should only be replaced in a nonhaz-

ardous area using the battery type specied

in this instruction manual.

WARRANTY:

This meter is warranted from all defects in materials and manufac-

turing for a period of two years. The electrode is warranted for

a period of one year. During this period, the required repair or

replacement of parts, where the damage is not due to negligence

or erroneous operation by the user, will be effected free of charge.

Otros manuales de Instrumento de medición de Milwaukee

Milwaukee

Milwaukee MW100 Manual de usuario

Milwaukee

Milwaukee REDLITHIUM 3521-20 Manual de usuario

Milwaukee

Milwaukee Smart PH Meter Manual de usuario

Milwaukee

Milwaukee M12 3632-20 Manual de usuario

Milwaukee

Milwaukee MI 404 Manual de usuario

Milwaukee

Milwaukee REDLITHIUM L4 3PL Manual de usuario

Milwaukee

Milwaukee REDSTICK MLDIG14 Manual de usuario

Milwaukee

Milwaukee 2205-20 Manual de usuario

Milwaukee

Milwaukee CD97 Manual de usuario

Milwaukee

Milwaukee SM700 Manual de usuario

Milwaukee

Milwaukee MA881 Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee LDM 30 Manual de usuario

Milwaukee

Milwaukee M12 CLLP Manual de usuario

Milwaukee

Milwaukee MI806 Manual de usuario

Milwaukee

Milwaukee ORP 57 Manual de usuario

Milwaukee

Milwaukee M12 ICAV3 Manual de usuario

Milwaukee

Milwaukee MA888 Manual de usuario

Milwaukee

Milwaukee LDM 45 Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee SM700 Manual de usuario

Milwaukee

Milwaukee MR100ATC Manual de usuario

Milwaukee

Milwaukee MW100 Manual de usuario

Milwaukee

Milwaukee 48-22-9802 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Milwaukee pH54 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas