Metrohm 930 Compact IC Flex SeS Manual de usuario
930 Compact IC Flex
930 Compact IC Flex SeS
Manual – Short Instructions
8.930.8107EN / v3 / 2023-03-31
Metrohm AG
CH-9100 Herisau
Switzerland
+41 71 353 85 85
www.metrohm.com
930 Compact IC Flex
930 Compact IC Flex SeS
2.930.1400
Manual – Short Instructions
8.930.8107EN / v3 / 2023-03-31
Technical Communication
Metrohm AG
CH-9100 Herisau
This documentation is protected by copyright. All rights reserved.
This documentation has been prepared with great care. However, errors
can never be entirely ruled out. Please send comments regarding possible
errors to the address above.
Disclaimer
Deficiencies arising from circumstances that are not the responsibility of
Metrohm, such as improper storage or improper use, etc., are expressly
excluded from the warranty. Unauthorized modifications to the product
(e.g. conversions or attachments) exclude any liability on the part of the
manufacturer for resulting damage and its consequences. Instructions and
notes in the Metrohm product documentation must be strictly followed.
Otherwise, Metrohm's liability is excluded.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents
930 Compact IC Flex SeS (2.930.1400) ￭￭￭￭￭￭￭￭ III
Table of contents
1 About this quick start guide 1
2 Introduction 2
2.1 Instrument description ......................................................... 2
2.2 Accessories and additional information ............................. 4
2.3 Symbols and conventions .................................................... 4
3 Safety 6
3.1 Intended use ......................................................................... 6
3.2 Responsibility of the operator ............................................. 6
3.3 Requirements for operating personnel ............................... 7
3.4 Safety instructions ................................................................ 7
3.4.1 General notes on safety ........................................................... 7
3.4.2 Electrical safety ........................................................................ 7
3.4.3 Tubing and capillary connections ............................................. 8
3.4.4 Flammable solvents and chemicals ........................................... 9
3.4.5 Recycling and disposal ............................................................. 9
4 Overview of the device 10
4.1 Front .................................................................................... 10
4.2 Rear ...................................................................................... 11
5 Installation 13
5.1 Setting up the instrument .................................................. 13
5.1.1 Packaging .............................................................................. 13
5.1.2 Checks .................................................................................. 13
5.1.3 Location ................................................................................ 13
5.2 Capillary connections in the IC system ............................. 13
5.3 Removing transport locking screws .................................. 14
5.4 Connecting the drainage tubing and leak sensor ............ 16
5.4.1 Installing the drainage tubing ................................................ 16
5.4.2 Connecting the leak sensor .................................................... 17
5.5 Connecting the eluent bottle ............................................. 18
5.6 Installing the high-pressure pump .................................... 20
5.7 Installing an inline filter ..................................................... 21
5.8 Installing the pulsation absorber ...................................... 21
5.9 Injection valve ..................................................................... 21
Table of contents ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
IV ￭￭￭￭￭￭￭￭ 930 Compact IC Flex SeS (2.930.1400)
5.10 Metrohm Suppressor Module (MSM) ............................... 21
5.10.1 Inserting the rotors ................................................................ 22
5.10.2 Connecting the Metrohm Suppressor Module (MSM) ............. 23
5.11 Metrohm CO2 Suppressor (MCS) ....................................... 26
5.11.1 Connecting the MCS ............................................................. 26
5.11.2 Installing the adsorber cartridge ............................................. 26
5.12 Installing the conductivity detector .................................. 28
5.13 Installing the amperometric detector ............................... 29
5.14 Connecting the instrument to a computer ....................... 29
5.15 Connecting the instrument to the power grid ................. 30
5.16 Initial start-up ..................................................................... 31
5.17 Connecting and rinsing the guard column ....................... 33
5.18 Connecting and rinsing the separation column ............... 34
5.19 Conditioning ........................................................................ 36
6 Operation 38
Index 39
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of figures
930 Compact IC Flex SeS (2.930.1400) ￭￭￭￭￭￭￭￭ V
Table of figures
Figure 1 Front ............................................................................................... 10
Figure 2 Rear ................................................................................................ 11
Figure 3 Removing the transport locking screws ............................................ 15
Figure 4 Installing the tubing weighting and aspiration filter .......................... 20
Figure 5 Metrohm Suppressor Module (MSM) – Connection capillaries .......... 24
Figure 6 Connecting the MCS ....................................................................... 26
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 About this quick start guide
930 Compact IC Flex SeS (2.930.1400) ￭￭￭￭￭￭￭￭ 1
1 About this quick start guide
This short instruction manual contains important chapters from the com-
prehensive manual. In addition to an introduction, safety instructions and
an overview of the instrument, you will also find information about instal-
ling and operating the 930 Compact IC Flex SeS as well as information
regarding the warranty. The comprehensive manual can be downloaded
as a PDF file from the Internet.
Downloading the manual
You can find the detailed manual on the Internet under
http://www.metrohm.com/:
1. Enter the order number for your instrument as the search term (e.g.
2.930.1400).
2. Click on Documents.
All available documents for the instrument will be displayed.
3. Click on the PDF link to download the desired manual.
2.1 Instrument description ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
2￭￭￭￭￭￭￭￭ 930 Compact IC Flex SeS (2.930.1400)
2 Introduction
2.1 Instrument description
The 930 Compact IC Flex is a robust ion chromatograph. It is distinguished
by:
￭Its intelligence: All of the functions are monitored, optimized and docu-
mented in an FDA-compatible manner. Intelligent components, such as
iColumns, save important data onto a chip.
￭Its compact design: It has a small footprint.
￭Its transparency: All components are easily accessible and located for
simple visibility and can be monitored during operation through a large
window.
￭Its safety: The wet end and the electronics are physically separated.
This prevents fluids from coming into contact with the electronics to a
large extent. A leak sensor is integrated into the wet end.
￭Its environmental compatibility.
￭Its low noise emission.
￭The intelligent MagIC Net software.
The 930 Compact IC Flex is operated using the MagIC Net software. A
USB cable is used to connect the device to a computer with MagIC Net
installed. The intelligent software detects the device automatically and
checks its functionality. The software controls and monitors the device,
evaluates the measured data and manages it in a database.
The 930 Compact IC Flex SeS consists of the following modules:
Housing
The sturdy housing contains the instrument's electronic components,
including their interfaces and one connector for a separation column. In
addition, the housing provides space for a conductivity detector or an
amperometric detector. Capillaries and cables can be fed into and out of
the instrument through several openings.
Leak sensor
The leak sensor detects leaking liquid that collects in the instrument's base
tray. Liquid that leaks in the instrument is routed to the base tray using
drainage tubing and detected there.
High-pressure pump
The intelligent and low-pulsation high-pressure pump pumps the eluent
through the IC system. It is equipped with a chip where its technical speci-
fications and "life history" (operating hours, service data, etc.) are stored.
Tabla de contenidos
Otros manuales de Equipo de laboratorio de Metrohm
Metrohm
Metrohm 862 Manual de usuario
Metrohm
Metrohm 900 Touch Control Instrucciones de operación
Metrohm
Metrohm 892 Professional Rancimat Manual de usuario
Metrohm
Metrohm 889 IC Sample Center Basic Manual de usuario
Metrohm
Metrohm 663 VA Stand Manual de usuario
Metrohm
Metrohm 838 Advanced Sample Processor Manual de usuario
Metrohm
Metrohm 883 Basic IC plus Manual de usuario
Metrohm
Metrohm 850 Professional IC Manual de usuario
Metrohm
Metrohm 768 KF Oven Manual de usuario
Metrohm
Metrohm 916 Ti-Touch Instrucciones de operación
Metrohm
Metrohm 942 Extension Module Vario HPG Manual de usuario
Metrohm
Metrohm 823 Membrane Pump Unit Manual de usuario
Metrohm
Metrohm ProfIC Vario 6 Anion Manual de usuario
Metrohm
Metrohm 940 Professional IC Vario ONE/ChS Manual de usuario
Metrohm
Metrohm 801 Manual de usuario
Metrohm
Metrohm OMNIS 2.1006.0010 Manual de usuario
Metrohm
Metrohm 787 KF Titrino Manual de usuario
Metrohm
Metrohm 902 Titrando Manual de usuario
Metrohm
Metrohm 793 IC Manual de usuario
Metrohm
Metrohm 917 Coulometer Manual de usuario
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
