Metrohm 889 IC Sample Center Basic Manual de usuario
889 IC Sample Center Basic
Manual
8.889.8004EN / v1 / 2023-01-10
Metrohm AG
CH-9100 Herisau
Switzerland
+41 71 353 85 85
www.metrohm.com
889 IC Sample Center Basic
Manual
8.889.8004EN / v1 / 2023-01-10
Technical Communication
Metrohm AG
CH-9100 Herisau
This documentation is protected by copyright. All rights reserved.
This documentation has been prepared with great care. However, errors
can never be entirely ruled out. Please send comments regarding possible
errors to the address above.
Disclaimer
Deficiencies arising from circumstances that are not the responsibility of
Metrohm, such as improper storage or improper use, etc., are expressly
excluded from the warranty. Unauthorized modifications to the product
(e.g. conversions or attachments) exclude any liability on the part of the
manufacturer for resulting damage and its consequences. Instructions and
notes in the Metrohm product documentation must be strictly followed.
Otherwise, Metrohm's liability is excluded.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents
889 IC Sample Center Basic ￭￭￭￭￭￭￭￭ III
Table of contents
1 Introduction 1
1.1 Device description ................................................................ 1
1.1.1 Model versions ........................................................................ 1
1.1.2 Device components ................................................................. 1
1.1.3 Accessories and additional information .................................... 2
1.2 About the documentation ................................................... 2
1.2.1 Symbols and conventions ........................................................ 2
2 Safety 4
2.1 Intended use ......................................................................... 4
2.2 Responsibility of the operator ............................................. 4
2.3 Requirements for operating personnel ............................... 5
2.4 Safety instructions ................................................................ 5
2.4.1 General notes on safety ........................................................... 5
2.4.2 Electrical safety ........................................................................ 5
2.4.3 Tubing and capillary connections ............................................. 7
2.4.4 Personnel safety ....................................................................... 7
2.4.5 Flammable solvents and chemicals ........................................... 8
2.4.6 Recycling and disposal ............................................................. 8
3 Overview of the device 9
3.1 Front and rear ....................................................................... 9
3.2 Opening the device ............................................................. 10
3.3 Interior view ........................................................................ 12
3.4 Interior ................................................................................. 13
3.5 Cooling option .................................................................... 14
4 Installation 15
4.1 Setting up the instrument .................................................. 15
4.1.1 Packaging .............................................................................. 15
4.1.2 Checks .................................................................................. 15
4.1.3 Location ................................................................................ 15
4.1.4 Removing the device from the packaging .............................. 15
4.2 Connecting the instrument to the power grid ................. 16
4.3 Connecting a computer ...................................................... 17
4.4 Tubing setup ....................................................................... 18
4.5 Drainage tubing .................................................................. 19
Table of contents ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
IV ￭￭￭￭￭￭￭￭ 889 IC Sample Center Basic
5 Operation and maintenance 21
5.1 General ................................................................................ 21
5.2 Care ...................................................................................... 21
5.2.1 Cleaning in general ................................................................ 22
5.3 Maintenance and service ................................................... 22
5.3.1 Replacing the sample needle ................................................. 22
5.3.2 Replacing the air needle ........................................................ 24
5.3.3 Replacing the fuses ................................................................ 25
6 Troubleshooting 26
6.1 Error list ............................................................................... 26
6.1.1 General ................................................................................. 26
6.1.2 Rack unit ............................................................................... 26
6.1.3 Needle unit ............................................................................ 27
6.1.4 Cooling unit .......................................................................... 29
6.1.5 Electronics ............................................................................. 29
6.2 Analytical problems ............................................................ 30
6.2.1 Autosampler .......................................................................... 30
7 Appendix 32
7.1 Samples and sample vials .................................................. 32
7.2 I/O interface ........................................................................ 32
7.2.1 Properties of the I/O interface ................................................ 33
7.2.2 Pin assignment of the remote interface .................................. 33
8 Technical specifications 34
8.1 General ................................................................................ 34
8.2 Sampling .............................................................................. 34
8.3 Interfaces ............................................................................. 35
8.4 Options (pre-installed) ........................................................ 35
8.5 Power connection ............................................................... 35
8.6 Ambient conditions ............................................................ 35
8.7 Dimensions .......................................................................... 36
Index 37
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of figures
889 IC Sample Center Basic ￭￭￭￭￭￭￭￭ V
Table of figures
Figure 1 889 IC Sample Center Basic - front .................................................... 9
Figure 2 889 IC Sample Center Basic - rear .................................................... 10
Figure 3 Interior view without covering ......................................................... 12
Figure 4 Interior with sampling equipment .................................................... 13
Figure 5 Interior view with installed cooling option ....................................... 14
Figure 6 Unpacking the 889 IC Sample Center Basic ...................................... 15
Figure 7 Mounting the outlet tubing ............................................................. 19
Figure 8 Mounting the leakage tubing .......................................................... 19
Figure 9 Connecting the outlet tubing .......................................................... 20
Figure 10 Replacing the sample needle ........................................................... 22
Figure 11 Pin assignment of I/O socket and plug ............................................. 33
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction
889 IC Sample Center Basic ￭￭￭￭￭￭￭￭ 1
1 Introduction
1.1 Device description
The 889 IC Sample Center Basic is a robust Autosampler for high sample
throughput, optimized for the challenges of the modern analytics labora-
tory. Its greatest advantages are small sample volumes and the cooling
option (8.889.0040).
Special features:
￭The control per PC software makes operation readily comprehensible.
A context-sensitive online help function is available for every window
and every dialog.
￭As a means of enhancing safety, no needle movements are carried out
when the door is open.
￭The optional sample cooling guarantees consistent results.
Standard microtiter plates (high or low form) or sample racks can be used.
Different plates or racks can be present in the left-hand and right-hand
loading drawers.
1.1.1 Model versions
2.889.0030 889 IC Sample Center Basic
With:
￭Needle with capillary, 79 µL (6.2816.220)
2.889.0040 889 IC Sample Center Basic – cool
With:
￭Needle with capillary, 79 µL (6.2816.220)
￭Accessories for cooling the samples
1.1.2 Device components
The 889 IC Sample Center Basic has the following components:
￭2 sample racks
Each for 48 vials.
￭Needle arm
With air needle and drives for horizontal and vertical positioning.
￭Cooling module (optional)
For cooling the samples.
￭USB connector
For the connection to a PC.
1.2 About the documentation ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
2￭￭￭￭￭￭￭￭ 889 IC Sample Center Basic
￭I/O interface
For output of an inject marker signal.
1.1.3 Accessories and additional information
Additional information is available on the Metrohm website (https://
www.metrohm.com):
￭Product family
￭Product versions
￭Accessories
￭Documents about the product
Downloading the accessories list
NOTICE
The accessories list is a part of the product documentation. Download
the accessories list and store it as a reference.
1. Use the search function to search for the product.
2. Open the desired product version.
3. Download the accessories list.
1.2 About the documentation
CAUTION
Read through this documentation carefully before putting the device
into operation. The documentation contains information and warnings
which the user must follow in order to ensure safe operation of the
device.
1.2.1 Symbols and conventions
The following symbols and styles are used in this documentation:
Cross-reference to figure legend
The first number refers to the figure number, the
second to the instrument part in the figure.
Instruction step
Carry out these steps in the sequence shown.
Tabla de contenidos
Otros manuales de Equipo de laboratorio de Metrohm
Metrohm
Metrohm Dosimat plus 876 Manual de usuario
Metrohm
Metrohm 930 Compact IC Flex Manual de usuario
Metrohm
Metrohm 717 Manual de usuario
Metrohm
Metrohm OMNIS 2.1006.0010 Manual de usuario
Metrohm
Metrohm 940 Professional IC Vario Series Manual de usuario
Metrohm
Metrohm 889 Manual de usuario
Metrohm
Metrohm 940 Professional IC Vario TWO Manual de usuario
Metrohm
Metrohm 838 Advanced Sample Processor Manual de usuario
Metrohm
Metrohm 945 Professional Detector Vario - Conductivity &... Manual de usuario
Metrohm
Metrohm 940 Professional IC Vario ONE/ChS/LPG Manual de usuario
Metrohm
Metrohm 942 Extension Module Vario Prep 2 Manual de usuario
Metrohm
Metrohm 940 Professional IC Vario ONE/SeS/PP/MB Manual de usuario
Metrohm
Metrohm 917 Coulometer Manual de usuario
Metrohm
Metrohm 806 Manual de usuario
Metrohm
Metrohm 843 Manual de usuario
Metrohm
Metrohm OMNIS 2.1002.0 10 Series Manual de usuario
Metrohm
Metrohm 942 Extension Module Vario LQH Manual de usuario
Metrohm
Metrohm ProfIC Vario 6 Anion Manual de usuario
Metrohm
Metrohm Eco KF Titrator Manual de usuario
Metrohm
Metrohm 916 Ti-Touch Instrucciones de operación
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
