Metra Electronics 99-7392B Manual de usuario

INSTALLATION INSTRUCTIONS

99-7392B

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT COMPONENTS

• A) Radio housing (front) • B) Radio housing (rear) • C) Radio brackets • D) Pioneer adapter brackets • E) Pocket • F) (4) #4 x 3/8” Phillips screws

• G) (6) #8 x 3/8” Phillips screws • H) Panel clip

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly

–ISO DIN radio provision with pocket...................4

–ISO DDIN radio provision......................................5

–Pioneer modular DDIN radio provision ......... 6-7

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring harness: 70-7306

Antenna adapter: 40-KI11

Steering wheel control interface: ASWC-1

12v to 6v camera step-down: AX-CAM6V

A B C D E

FGH

Hyundai Kona 2018-up

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision †

• Pioneer modular DDIN radio provision †

• Painted matte black

† This kit can only be used with an ISO DDIN radio with an “L” shaped chassis design, with the radio

chassis at the bottom of the screen. As of this writing, only the Alpine INE-W967HD (discontinued,

replaced by INE-W977HD), iLX-107, and iLX-207 have this design. Also, The Pioneer modular radios,

DMH-C2550NEX and DMH-C2500NEX, can also be used with the included adapter brackets.

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

1.800.221.0932

MetraOnline.com

DASH DISASSEMBLY

1. Unclip and remove the speedometer

cluster bezel, and the top trim from the

steering column. These will come out

as one piece, connected by material.

(Figure A)

2. Unclip and remove the entire panel that

houses the center and right a/c vent.

(Figure B)

Continue to Kit Preparation

(Figure A) (Figure B)

REV. 6/21/2019 INST99-7392B 3

KIT PREPARATION

1. Remove the top trim piece behind

the radio:

a. Unclip the (3) clips securing the

front of the trim. (Figure A)

b. Slide the trim to the left, then up

and slightly back to release the

trim. A little ﬁnesse is required with

this process. (See inset)

2. Remove (2) Phillips screws securing the

back of the radio. (Figure B)

3. Remove (2) Phillips screws securing the

bottom of the radio. Take note that the

radio brackets are angled inward, hiding

the screws from being easily seen. Slide

the radio out, then unplug and remove

the radio. (Figure C)

Continue to Kit Assembly

(Figure A) (Figure B) (Figure C)

Bottom side of trim panel

1.800.221.0932

MetraOnline.com

KIT ASSEMBLY

ISO DIN radio provision with pocket

1. Secure the

radio brackets

to the

pocket

using (2) #8 x 3/8” Phillips screws

provided. (Figure A)

2. Attach the

panel clip

provided onto the

radio housing (front)

3. Secure the bracket/pocket assembly to

the

radio housing (front)

using (4) #8 x

3/8” Phillips screws provided. (Figure B)

4. Remove the metal DIN sleeve and trim

ring from the aftermarket radio.

5. Slide the radio into the bracket/housing/

pocket assembly from the back, then

secure it to the assembly using the

screws supplied with the radio.

(Figure C)

(Figure B) (Figure D)

(Figure C)(Figure A)

6. Secure the

radio housing (rear)

to the

radio assembly using (4) #4 x 3/8”

Phillips screws provided. (Figure D)

7. Locate the factory wiring harness and

antenna connector in the dash and

complete all necessary connections to

the radio. Metra recommends using

the proper mating adapter from Metra

and/or Axxess. Test the radio for proper

operation.

8. Secure the radio assembly to the dash

using the (4) factory screws.

9. Reassemble the dash in reverse

order of disassembly to complete the

installation.

REV. 6/21/2019 INST99-7392B 5

KIT ASSEMBLY

ISO DDIN radio provision

1. Attach the

panel clip

provided onto the

radio housing (front)

2. Secure the

radio brackets

to the

radio

housing (front)

using (4) #8 x 3/8”

Phillips screws provided. (Figure A)

3. Slide the radio into the bracket/housing

assembly from the back, then secure

it to the assembly using the screws

supplied with the radio. (Figure B)

4. Secure the

radio housing (rear)

to the

radio assembly using (4) #4 x 3/8”

Phillips screws provided. (Figure C)

(Figure B)

(Figure C)(Figure A)

5. Locate the factory wiring harness and

antenna connector in the dash and

complete all necessary connections to

the radio. Metra recommends using the

proper mating adapter from Metra

and/or Axxess. Test the radio for

proper operation.

6. Secure the radio assembly to the dash

using the (4) factory screws.

7. Reassemble the dash in reverse

order of disassembly to complete the

installation.

1.800.221.0932

MetraOnline.com

Pioneer Modular DDIN radio provision

Note: For steps 3 and 4, reference the

installation manual provided with the

radio for which hardware to use. The

display screen and radio chassis use two

different types of screws.

1. Attach the

panel clip

provided onto the

radio housing (front)

2. Secure the

radio brackets

to the

radio

housing (front)

using (4) #8 x 3/8”

Phillips screws provided. (Figure A)

3. Secure the radio display to the

Pioneer

adapter brackets

using (6) screws

supplied with the radio. (Figure B)

(Figure B)

(Figure C)(Figure A)

4. Secure the display/bracket assembly

to the radio chassis using (4) screws

supplied with the radio. (Figure C)

5. Slide the radio assembly into the

bracket/housing assembly from the

back, then secure it to the assembly

using the screws supplied with the

radio. (Figure D)

Continued on the next page

KIT ASSEMBLY

(Figure D)

REV. 6/21/2019 INST99-7392B 7

6. Secure the radio housing (rear) to the

radio assembly using (4) #4 x 3/8”

Phillips screws provided. (Figure E)

7. Locate the factory wiring harness and

antenna connector in the dash and

complete all necessary connections to

the radio. Metra recommends using the

proper mating adapter from Metra

and/or Axxess. Test the radio for

proper operation.

8. Secure the radio assembly to the dash

using the (4) factory screws.

Reassemble the dash in reverse order of

disassembly to complete the installation

KIT ASSEMBLY (CONT.)

(Figure E)

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certiﬁed technicians

INSTALLATION INSTRUCTIONS

99-7392B

If you are having difﬁculties with the installation

of this product, contact our Tech Support line

either by phone at 1-800-253-TECH, or email at

techsupport@metra-autosound.com. Before

doing so, look over the instruction booklet a

second time and ensure that the installation was

performed exactly as the instruction booklet

is stated. Have the vehicle apart and ready to

perform troubleshooting steps before contacting

Metra/Axxess Tech Support.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Metra Electronics

Metra Electronics

Metra Electronics 99-7617HG Manual de usuario

Metra Electronics

Metra Electronics 99-3303 Manual de usuario

Metra Electronics

Metra Electronics iBeam TE-AHD7M Manual de usuario

Metra Electronics

Metra Electronics 70-1722 Manual de usuario

Metra Electronics

Metra Electronics 99-7504 Manual de usuario

Metra Electronics

Metra Electronics ACURA 99-7866 Manual de usuario

Metra Electronics

Metra Electronics 71-7552 Manual de instrucciones

Metra Electronics

Metra Electronics 70-6522 Manual de usuario

Metra Electronics

Metra Electronics 71-5520 Manual de usuario

Metra Electronics

Metra Electronics 95-3314G Manual de usuario

Metra Electronics

Metra Electronics 99-4644 Manual de usuario

Metra Electronics

Metra Electronics 108-TO6HG Manual de usuario

Metra Electronics

Metra Electronics LEXUS ES 95-8150 Manual de usuario

Metra Electronics

Metra Electronics 99-8724B Manual de usuario

Metra Electronics

Metra Electronics 99-9100 Manual de usuario

Metra Electronics

Metra Electronics 99-1003 Manual de usuario

Metra Electronics

Metra Electronics 99-5027 Manual de usuario

Metra Electronics

Metra Electronics 99-7878B Manual de usuario

Metra Electronics

Metra Electronics 99-3051 Manual de usuario

Metra Electronics

Metra Electronics 99-7425 Manual de usuario

Metra Electronics

Metra Electronics 99-8715 Manual de usuario

Metra Electronics

Metra Electronics 99-7867 Manual de usuario

Metra Electronics

Metra Electronics 95-7350B Manual de usuario

Metra Electronics

Metra Electronics 99-5716 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario