Metra Electronics 99-7878B Manual de usuario

INSTALLATION INSTRUCTIONS FOR PART 99-7878B

99-7878B

APPLICATIONS

HONDA Insight

2010

KIT FEATURES

•DIN Radio Provision with Pocket

•ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

•Stacked ISO Mount Units Provision

• Painted A Matte Black Finish

•A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

•E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

•Phillips Screwdriver • Socket Wrench

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

Dash Disassembly

HondaInsight2010 .................................

1,2

Kit Assembly

-Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

-DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4

-ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5

-Double DIN /Stacked ISO Mount Units Radio Provision . . . . . . . . . . . . .6

TABLE OF CONTENTS

99-7878B

Note:

Refer also to the instructions included with the aftermarket radio.

NOWLEDGE IS

OWER

Enhanceyour installation and fabrication skills

by enrolling inthe most recognized andrespected

mobile electronics school in our industry.

Log onto www.installerinstitute.com

or call 800-354-6782 formore information

and take stepstoward abetter tomorrow.

HONDAINSIGHT 2010

95-7878B DASH DISASSEMBLY

Disconnect the negative battery

terminal to prevent an accidental short

circuit.

Unclip and remove the pocket/acces-

sory socket panel below the factory

radio.

(Figure A)

Open the glove box then use a small

blunt tool (ie: the wooden handle of a

hammer) to put pressure on the back

of the radio chassis to unclip and

remove the radio.

(Figure C)

Continued on page 2.

Remove (1) 8 MM bolt facing up

behind panel.

Figure B)

OFF

REAR

FRONT

AUTO

PUSH

POWER

OUTLET

OFF

REAR

FRONT

AUTO

PUSH

HONDAINSIGHT 2010

95-7878B DASH DISASSEMBLY

Remove (2) Phillips screws securing the hazard switch to the back of the factory

radio panel. (Figure D)

Remove the (8) retaining clips from the factory radio panel.

(Figure D)

Continue to kit preparartion.

Remove (2) Phillips screws securing the air bag light to the back of the factory radio

panel.

(Figure D)

HAZARD

SWITCH

TWO

SCREWS

AIR BAG

SWITCH

TWO

SCREWS

8 RETAINING CLIPS

99-7878B KIT PREPARATION

KIT PREPARATION

Secure the hazard switch into the radio housing panel using the factory hardware.

(

Figure A)

Secure the air bag light into the radio housing panel using the factory hardware.

(

Figure A)

Attach the (8) retaining clips to the radio housing panel in the same location as

removed from the factory radio panel. (

Figure A)

Continue to kit assembly.

HAZARD

SWITCH

TWO

SCREWS

AIR BAG

SWITCH

TWO

SCREWS

8 RETAINING CLIPS

99-7878B KIT ASSEMBLY

DIN MOUNT RADIO PROVISION WITH POCKET

Locate the factory wiring harness in

the dash. Metra recommends using

the proper mating adapter from Metra

or AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

Slide the DIN cage into the Radio

Housing and secure by bending the

metal locking tabs down.

(Figure A)

Snap the pocket into the bottom

opening of the radio housing.

(Figure B)

Slide the aftermarket head unit into

the cage and secure.

(Figure C)

Reassemble dash in reverse order of

disassembly.

Note: Refer also to the instructions included with the aftermarket radio.

99-7878B KIT ASSEMBLY

ISO MOUNT RADIO PROVISION WITH POCKET

Locate the factory wiring harness in

the dash. Metra recommends using

the proper mating adapter from Metra

or AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

Mount the ISO Brackets to the head

unit with the screws supplied with

the unit.

(Figure A)

Snap the pocket into the bottom

opening of the radio housing.

(Figure B)

Slide the head unit into the radio

opening until the side clips engage.

(Figure C)

Snap the Trim plate into the Radio

Housing.

(Figure C)

Reassemble dash in reverse order of

disassembly.

Note: Refer also to the instructions included with the aftermarket radio.

99-7878B KIT ASSEMBLY

DOUBLE DIN/STACKED ISO MOUNT

UNITS RADIO PROVISION

Locate the factory wiring harness in

the dash. Metra recommends using

the proper mating adapter from Metra

or AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

Cut and remove the center bar from

the radio housing.

(Figure A)

Snap the Double DIN brackets to the

inside edge of the Double DIN trim

plate.

(Figure B)

Slide the Double DIN head unit or

stacked ISO head units into the

bracket/radio housing assembly and

secure the Double DIN head unit or

stacked ISO head units to the

assembly using the screws supplied

with the radio.

(Figure C)

Note: Refer also to the instructions included with the aftermarket radio.

Reassemble dash in reverse order of

disassembly.

Snap the Double DIN trim plate into the

Radio Housing.

(Figure C)

1-800-221-0932

www.metraonline.com

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Metra Electronics

Metra Electronics

Metra Electronics 95-7866B Manual de usuario

Metra Electronics

Metra Electronics 99-3107S Manual de usuario

Metra Electronics

Metra Electronics 95-7337B Manual de usuario

Metra Electronics

Metra Electronics 99-7502 Manual de usuario

Metra Electronics

Metra Electronics 99-7953 Manual de usuario

Metra Electronics

Metra Electronics 99-6510 Manual de usuario

Metra Electronics

Metra Electronics 99-7404 Manual de usuario

Metra Electronics

Metra Electronics 95-7617B Manual de usuario

Metra Electronics

Metra Electronics METRA 99-7603 Manual de usuario

Metra Electronics

Metra Electronics 99-7863 Manual de usuario

Metra Electronics

Metra Electronics 95-8154 Manual de usuario

Metra Electronics

Metra Electronics 95-6547B Manual de usuario

Metra Electronics

Metra Electronics 99-7414 Manual de usuario

Metra Electronics

Metra Electronics 95-5817 Manual de usuario

Metra Electronics

Metra Electronics 99-3012G Manual de usuario

Metra Electronics

Metra Electronics 99-7867 Manual de usuario

Metra Electronics

Metra Electronics 99-9100 Manual de usuario

Metra Electronics

Metra Electronics 95-7313 Manual de usuario

Metra Electronics

Metra Electronics 95-7325 Manual de usuario

Metra Electronics

Metra Electronics 99-6507 Manual de usuario

Metra Electronics

Metra Electronics 99-8201 Manual de usuario

Metra Electronics

Metra Electronics 108-TO7HG Manual de usuario

Metra Electronics

Metra Electronics 99-3009 Manual de usuario

Metra Electronics

Metra Electronics 98-8999 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario