Martin FiberSource QFX 150 Manual de usuario

FiberSource QFX 150

user manual

35000079B.fm Page 1 Thursday, December 9, 1999 11:47 AM

1 cooling fan

2 lamp access

cover screw

3 adaptor set screw

4 cable socket

5 mounting flange

6 DIP-switch

7 data sockets

8 AC input & main

fuse

reproduced, in any form or by any means, without

permission in writing from Martin Professional A/S,

Denmark.

Printed in Denmark.

P/N 35000079, Rev. B

35000079B.fm Page 2 Thursday, December 9, 1999 11:47 AM

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

LAMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

AC POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

FIBER OPTIC CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

CONTROLLER OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

STAND-ALONE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

MASTER/SLAVE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

BASIC SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

35000079B.fm Page 3 Thursday, December 9, 1999 11:47 AM

4 Introduction

NTRODUCTION

Thank you for selecting the Martin FiberSource QFX 150. This fiber optic lighting

fixture uses a long-life 150 watt discharge lamp and provides 4 colors plus white,

full-range dimming, and a variable-speed twinkle effect. It operates with DMX-512

controllers, in stand-alone mode, and in master/slave configuration.

SAFETY INFORMATION

Warning! This product is for professional use only. It is not for household use.

This product presents risks of lethal or severe injury due. Read this manual before

powering or installing the fixture, follow the safety precautions listed below and

observe all warnings in this manual and on the fixture. If you have questions about

how to operate the fixture safely, please contact your Martin dealer or call the

Martin 24-hour service hotline.

To protect yourself and others from electric shock

• Disconnect the fixture from power before removing or installing the lamp, fuses, or

any part, and when not in use.

• Always ground (earth) the fixture electrically.

• Use only a source of power that complies with local building and electrical codes

and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Refer all service to a qualified technician.

To protect yourself and others from UV radiation and lamp

explosion

• Do not operate the fixture without a fiber optic cable inserted.

• When replacing the lamp, allow the fixture to cool for at least 5 minutes before

opening. Protect your hands and eyes with gloves and safety glasses.

• Never look at a lamp while it is lit.

• Replace the lamp when it becomes defective or worn out, or before usage exceeds

110 percent of the rated average life.

35000079B.fm Page 4 Thursday, December 9, 1999 11:47 AM

Introduction 5

To protect yourself and others from burns and fire

• Never attempt to bypass the thermostatic switch or fuses. Always replace defective

fuses with ones of the specified type and rating.

• Keep all combustible materials (for example fabric, wood, paper) at least 0.1 meters

(4 inches) away from the fixture. Keep flammable materials well away from the

fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.

• Allow the fixture to cool before handling.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).

To protect yourself and others from injury due to falls

• When suspending the fixture above ground level, verify that the structure can hold

at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened and use an

approved means of secondary attachment such as a safety cable.

• Block access below the work area whenever installing or removing the fixture.

UNPACKING

The packing material is carefully designed to protect the fixture during shipment -

always use it to transport the fixture.

The FiberSource QFX 150 comes with:

• Osram HQI-R 150 W lamp

• 3 m power cable w/ 3-pin IEC female cord cap

• 4 dichroic color filters

•usermanual

35000079B.fm Page 5 Thursday, December 9, 1999 11:47 AM

6 Lamp

AMP

The FiberSource QFX 150 is designed for use with the Osram HQI-R 150 lamp. Do

not install any other type of lamp.

Warning! Disconnect the fixture from power and allow it to cool before

opening.

Important! Turn the lamp so that the arc is horizontal.

To install or position the lamp

1 Remove the 4 lamp access

cover screws and pull off the

access cover, which is

indicated by the arrow on the

rear panel.

2 To remove the lamp, place a

hand under it and pull it out. Do

not lift by the ceramic base

alone. Squeeze the sides of the

lamp plug and pull it out.

3 To position the lamp, turn it so the wires,

where they exit the lamp base, point

towards the ground when the fixture is

installed

This puts the arc in its ideal

burning position.

4 To install a lamp, plug in the connector

and then place the reflector rim in the

slot. Gently press the lamp between the

springs until it snaps into place.

5 Remove and turn the diffusion filter 90°, if necessary, so the long sides of the

prisms align with the arc.

6 Check the power setting as described in the next section before replacing the

lamp access cover.

Turn lamp so wires

point towards

ground and arc is

horizontal.

Align long edge of

diffuser prisms

with arc.

35000079B.fm Page 6 Thursday, December 9, 1999 11:47 AM

AC power 7

POWER

The FiberSource QFX 150 has 10 switch-selectable power supply settings. Always

use the setting that is closest to the local AC supply.

Warning! For protection from electric shock, the fixture must be grounded

(earthed). The power supply shall have overload and ground-

fault protection.

Important! Install fuse and verify that power supply settings match local

AC supply before use.

To check or change the voltage

setting

1 Disconnect the fixture from power.

Remove the lamp access cover.

2 Set the 5-position switch to the

setting closest to the AC voltage. Use

the higher setting if the voltage is

halfway between 2 settings. For

example, use the 230 V setting

instead of the 210 V setting for

operation with 220 V power.

3 Set the 2-position switch to the AC

frequency (50 / 60 Hz).

4 Replace the cover and apply a new

power setting label to the serial

number label.

50Hz

60Hz

250 V

230 V

210 V

100 V

120 V

35000079B.fm Page 7 Thursday, December 9, 1999 11:47 AM

8 AC power

To install the main fuse

Fuses are provided for 100 - 130 V and 200 - 250 V operation. Use only the fuse

specified for the operating voltage.

1 Locate the bag containing the fuse for your AC voltage. Insert the fuse in the

fuse holder. The holder may be packed with the other fuse.

2 Remove the label covering the mains input socket.

3 Insert the fuse holder in the empty slot in the mains input socket. See also “To

replace the main fuse” on page 20.

To install a plug on the power cable

The power cable must be fitted with a grounding-type cord cap that fits your power

distribution system. Consult an electrician if you have any doubts about proper

installation.

Important! Verify that the feed cables are undamaged and rated for the

current requirements of all connected devices before use.

• Following the cord cap manufacturer’s instructions, connect the yellow and

green wire to ground (earth), the brown wire to live, and the blue wire to neutral.

The table below shows some pin identification schemes.

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

35000079B.fm Page 8 Thursday, December 9, 1999 11:47 AM

Installation 9

NSTALLATION

The FiberSource QFX 150 can be fastened directly through the 4 rubber washers in

the mounting flanges, or hung with 2 rigging clamps (not included) fastened

through the 13 mm holes.

INSTALLATION REQUIREMENTS

For optimum performance and ease of service, install the fixture such that

• The long axis is horizontal as

shown in A to right. This

positions the lamp electrodes

for maximum lamp life. Do not

install as shown in B.

• The minimum clearance around

the fans and air vents at both

ends is 10 cm (4 in.) and

circulation is adequate keep the

air around the fixture at 40° C

(104° F) or below.

• The DIP-switch is accessible and there is room to insert cables.

• The lamp access panel can be removed.

• All safety requirements are met.

To install the FiberSource QFX 150

Warning! Always use a secure means of secondary attachment when

hanging the fixture with clamps.

1 Verify that the fasteners or clamps can bear 10 times the fixture’s weight. Verify

that the structure can support 10 times the weight of all installed fixtures,

clamps, cables, auxiliary equipment, etc.

2 Block access below the work area.

3 If fastening directly, place a metal washer over each rubber washer. The metal

washer must be as wide as the rubber washer, or wider, to insure a secure hold.

Fasten with 4 suitable fasteners 4 - 5 mm (5/32 - 3/16 in.) in diameter.

35000079B.fm Page 9 Thursday, December 9, 1999 11:47 AM

10 Installation

4 If clamping, bolt the clamps securely to the flanges with grade 8.8 (minimum)

M12 bolts and lock nuts, or as recommended by the clamp manufacturer,

through the 13 mm holes. Install a safety cable that can hold at least 10 times

the weight of the fixture through one of the small holes and around the truss or

pipe. Remove a rubber washer if necessary to thread the safety cable.

5 Verify that the fixture is located at least 0.1 meters (4 in.) from any combustible

materials. Verify that the clearance around the fan and air vents is at least 0.1

meters (4 in.). Verify that there are no flammable materials nearby.

35000079B.fm Page 10 Thursday, December 9, 1999 11:47 AM

Tabla de contenidos

Otros manuales de Equipo de iluminación de Martin

Martin

Martin MAC 250 Wash Manual de usuario

Martin

Martin CX-10 Extreme Manual de usuario

Martin

Martin MAC 500E Manual de usuario

Martin

Martin Exterior 200 LED Manual de usuario

Martin

Martin MAC 500 Manual de usuario

Martin

Martin MAC 2000 Profile II Manual de usuario

Martin

Martin Exterior Projection 500 Manual de usuario

Martin

Martin MAC 350 Entour Manual de usuario

Martin

Martin MAC 250 Wash Manual de usuario

Martin

Martin MAC 2000 Profile II Manual de usuario

Martin

Martin EvenLED RGB LED Panel Manual de usuario

Martin

Martin MAC 575 Krypton Manual de usuario

Martin

Martin MAC 101 Series Manual de usuario

Martin

Martin Mania EF3 Manual de usuario

Martin

Martin MAC Viper Profile Manual de usuario

Martin

Martin LightCorder Manual de usuario

Martin

Martin Acrobat Manual de usuario

Martin

Martin Extube Manual de usuario

Martin

Martin MAC 700 PROFILE Manual de usuario

Martin

Martin EC Series LED Video Panel Guía del usuario

Martin

Martin RUSH MH 6 Wash CT Manual de usuario

Martin

Martin MAC 700 WASH Manual de usuario

Martin

Martin MAC 300 Manual de usuario

Martin

Martin P3-100 Guía del usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario